Journal of Composites for Construction

This study concentrates on analytical evaluation of the effect of external confinement using fiber reinforced polymers (FRP) sheets on the response of concrete rectangular columns designed for gravity load only and having spliced longitudinal reinforcement at the column base. A general analytical scheme for evaluating the strength capacity and ductility of the columns under combined flexural–axial loads was developed. The analysis takes into account the bond strength degradation of the spliced reinforcement with increase in lateral load by incorporating a generalized bond stress–slip law, and considers the effect of FRP confinement on the stress–strain response of concrete material. Particular emphasis is placed in the analysis on the slip response of the spliced bars and the consequent fixed end rotation that develops at the column base. Results predicted by the analysis showed very good agreement with limited experimental data. A parametric evaluation was carried out to evaluate the effect of different design and strength parameters on the column response under lateral load. Without confinement, the columns suffered premature bond failure and, consequently, low flexural strength capacity. Confining the concrete in the columns end zone at the splice location with FRP sheets enhanced the bond strength capacity of the spliced reinforcement, increased the steel stress that can be mobilized before bond failure occurs, and consequently improved the flexural strength capacity and ductility of the columns. A general design equation, expressed as a function of the main parameters that influence the bond strength capacity between spliced steel bars and FRP confined concrete, is proposed to calculate the area of FRP sheets needed for strengthening of the subject columns.

Very little information is available on the behavior of fiber reinforced polymer (FRP) materials and FRP-strengthened concrete members in fire, and this is a primary factor hindering the widespread implementation of FRP strengthening technologies in the construction industry. This paper presents a numerical model for evaluating the fire behavior of conventionally reinforced circular concrete columns, FRP-wrapped reinforced concrete columns, and insulated FRP-wrapped reinforced concrete columns. The model is validated against data available in the literature from full-scale fire endurance tests on conventionally reinforced concrete columns, and preliminary predictions of the model are presented and discussed. It is demonstrated that the model agrees reasonably well with experimental data obtained from tests on circular reinforced concrete columns, that it is unlikely that the structural effectiveness of FRP materials can be maintained during fire, and that the fire behavior of FRP-wrapped columns can be dramatically improved by providing supplemental insulation for the FRP.

This paper presents results of an experimental investigation on three beams and five short columns, consisting of glass fiber reinforced polymer concrete-filled rectangular filament-wound tubes (CFRFTs). The tubes included fibers oriented at $\pm 45$ ° and 90° with respect to the longitudinal axis. Additional longitudinal fibers [0°] were provided in flanges for flexural rigidity. Beams included totally filled tubes and a tube partially filled with concrete, which had a central hole for reducing deadweight. The effect of reinforcement ratio was examined by using tubes of two different sizes. Flexural behavior of CFRFT was compared to concrete-filled rectangular steel tubes (CFRSTs) of similar reinforcement ratios. Short columns were tested under eccentricity ratios $(e∕h)$ of 0, 0.09, 0.18, and 0.24, where $h$ is the section depth. Transverse strains were measured around the perimeter of concentrically loaded column to evaluate confinement effect. The study showed that CFRFT is a feasible system that could offer similar flexural strength to CFRST. The tube laminate structure and its progressive failure contribute to the slightly nonlinear behavior of beams. The CFRFT beam with inner hole had an overall strength-to-weight ratio, 77% higher than the totally filled beam, but failed in compression. Bulging of CFRFT columns has limited their confinement effectiveness.

This paper presents an analytical model to predict the behavior of concrete-filled rectangular fiber reinforced polymer (FRP) tubes (CFRFTs), subjected to bending and axial loads. The model accounts for different laminate structures of the flange and web of the tube. Gradual reduction of stiffness, resulting from progressive failure of FRP layers oriented at various angles is considered through the ultimate laminate failure approach. The model adopts cracked section analysis, using layer-by-layer approach and accounts for totally and partially filled tubes. The model predicts the moment–curvature responses of beams, load–strain responses of columns, and complete interaction curves of beam–columns. The model is verified using experimental results and is used to study the effects of laminate structure, hybrid laminates, thickness of the tube and optimization of partially filled tubes. Comparisons of CFRFT with conventional reinforced concrete (RC) sections showed that CFRFT could provide axial load–bending moment interaction curves comparable to those of RC sections of similar reinforcement index. Also, providing a small fraction of carbon fibers in the flanges could substantially improve flexural performance. The first ply failure approach could highly underestimate the strength of CFRFT.

This paper reports on the fourth phase of a multiphase study undertaken at the American University of Beirut (AUB) to examine the effect of fiber-reinforced polymer (FRP) sheets in confining bond-critical regions in reinforced concrete beams. Results of the first three phases showed that glass- and carbon-fiber-reinforced polymer (GFRP and CFRP) sheets were effective in increasing the bond strength and improving the ductility of the mode of failure of tension lap splices in high-strength concrete (HSC) and normal-strength concrete (NSC) beams. The main objective of the fourth phase of the AUB study was to assess the effect of CFRP sheets in improving the serviceability and ultimate response of beam anchorage specimens. The added experimental data and the improved knowledge of the bond behavior of FRP confined concrete members will encourage the use of FRP technology to strengthen and retrofit bond anchorage zones. Ten beam anchorage specimens were tested in positive bending in two series. The variables were bar size, anchorage length, and concrete strength. For each bar size, anchorage length, and concrete strength, two companion specimens—identical except for whether the anchorage zone was wrapped with FRP sheets or not wrapped—were tested. The test results demonstrated that CFRP sheets were effective in enhancing the bond strength and ductility of anchorage zones in beam anchorage specimens where splitting failures were imminent.

A new analytical method for defining the nonlinear bond stress–slip models of fiber reinforced plastics (FRP) sheet–concrete interfaces through pullout bond test is proposed. With this method, it is not necessary to attach many strain gauges on the FRP sheets for obtaining the strain distributions in FRP as well as the local bond stresses and slips. Instead, the local interfacial bond stress-slip models can be simply derived from the relationships between the pullout forces and loaded end slips. Based on a series of pullout tests, the bond stress–slip models of FRP sheet–concrete interfaces, in which different FRP stiffness, FRP materials (carbon FRP, aramid FRP, and glass FRP), and adhesives are used, have been derived. Only two parameters, the interfacial fracture energy and interfacial ductility index, which can take into account the effects of all interfacial components, are necessary in these models. Comparisons between analytical results and experimental ones show good accordance, indicating the reliability of the proposed method and the proposed bond stress–slip models.

The problem of long-term creep deformation of reinforced concrete tensile elements strengthened by external fiber reinforced plastic (FRP) plates is studied. Formation of discrete cracks in concrete under tension is taken into account. A kinematic model is used, where relative slips between concrete, steel bars, and FRP plates are considered, governed by viscous interface shear stress–slip laws. Bazant’ solidification theory and exponential algorithm are used to obtain incremental constitutive equations for concrete as well as for steel-concrete and FRP-concrete interface laws. Moreover, cohesive normal stresses across transverse cracks in concrete are considered. The incremental differential system of equations is transformed into a nonlinear algebraic system by a finite difference discretization with respect to axial coordinate. Several numerical examples are presented, concerning both short-term and long-term loadings. It is shown that reinforcing by means of FRP plates or sheets has significant beneficial effects on the behavior of reinforced concrete elements under service loadings because (1) it increases concrete tension stiffening effect and (2) it strongly reduces crack width. The present study shows that these beneficial effects are preserved also in the case of long-term loadings.

An experimental investigation was conducted to study the in-plane behavior of face shell mortar bedded unreinforced masonry (URM) wall assemblages retrofitted with fiber-reinforced polymer (FRP) laminates. Forty-two URM assemblages were tested under different stress conditions present in masonry shear and infill walls. Tests included prisms loaded in compression with different bed joint orientation (on/off-axis compression), diagonal tension specimens, and specimens loaded under joint shear. The behavior of each specimen type is discussed with emphasis on modes of failure, strength and deformation characteristics. Results showed that the application of FRP laminates on URM has a great influence on strength, postpeak behavior, as well as altering failure modes and maintaining the specimen integrity. The retrofitted specimens reached compressive strength of 1.62–5.64 times that of their unretrofitted counterparts, depending on the bed joint orientation, and joint shear strength increased by eightfold.

Restrained shrinkage is a major source of damage to buildings. By the combination of different construction materials, or through different conditions of exposure of different structural elements, differential dimensional change occurs. Thereby, stresses arise, which can cause cracking. In recent combined experimental and numerical research projects, this source of damage to masonry walls has been confirmed. The ability has been developed to predict the level of damage computationally. This paper addresses a method to reduce the width of cracks in masonry walls subjected to restrained shrinkage, to acceptable levels. Crack control by externally applied carbon fiber reinforced polymer (CFRP) reinforcement is studied. Although structural strengthening by CFRP reinforcement is actively researched, its application here to preserve structural serviceability is novel. An experiment was designed and performed to study the response of an unreinforced masonry wall to restrained shrinkage. Subsequently, the wall was repaired and reinforced on one face with CFRP strips. The required CFRP reinforcement was designed by finite element analysis, which also served as prediction of the response of the reinforced wall to restrained shrinkage.

The use of plasticity-based shear design methods for fiber-reinforced polymer (FRP) reinforced and prestressed concrete, as they are used at present, is inappropriate in the long term. In particular, the use of a plasticity-based truss model for shear behavior seems to be unsound, as reliance is placed on a predominantly elastic zone to redistribute stresses. A better approach to shear design would be to employ a model incorporating force equilibrium and compatibility of strains so that the elastic properties of the FRP could be included rationally. This would help to develop a real understanding and form a basis on which new guides and codes could be founded. In tandem with a more rational analytical approach, new configurations and types of FRP reinforcement need to be developed and researched so that these materials can be used more efficiently. An analytical approach to investigate the shear response of FRP-reinforced and -prestressed concrete has been developed, based on equilibrium and compatibility across a shear discontinuity. The analytical model presented here was developed in conjunction with an experimental program. Correlation between the analytical and experimental results is good and more accurate than the current guideline provisions for concrete beams containing FRP reinforcement.

This paper presents a simple model to calculate concrete properties for reinforced concrete members that are confined by carbon-fiber-reinforced plastic (CFRP) sheets. The model simplifies and incorporates formulas from some of the existing models. Results are examined for typical circular and square columns with a range of cross-section dimensions and axial loads. Results demonstrate that the proposed simple model is quite sufficient in calculating moment-curvature relationships of CFRP-confined members.