Journal of Composites for Construction

This paper deals with masonry arches and vaults strengthened with surface fiber-reinforced polymer (FRP) reinforcement in the form of strips bonded at the extrados and/or intrados, considering strip arrangements that prevent hinged mode failure, so the possible failure modes are: (1) crushing, (2) sliding, (3) debonding, and (4) FRP rupture. Mathematical models are presented for predicting the ultimate load associated with each of such failure modes. This study has shown that the reinforced arch is particularly susceptible to failure by crushing, as a result of an ultimate compressive force being collected by a small fraction of the cross section. Failure by debonding at the intrados may also be an issue, especially in the case of weak masonry blocks or multiring brickwork arches. Failure by sliding has to be considered if the reinforcement is at the extrados and loading is considerably nonsymmetric.

The current method of bonding fiber-reinforced polymer (FRP) strengthening strips to concrete structures requires extensive time and semiskilled labor. An alternative method is to use a commercial off-the-shelf powder-actuated fastening system to attach FRP strips to concrete. A series of flexural tests were conducted on 15 $304.8\times 304.8\times 3\text{,}657.6\mathrm{mm}$ $(12\times 12\times 144\mathrm{in}\text{.})$ reinforced concrete beams. Two beams were tested unstrengthened, 12 were strengthened with mechanically fastened FRP strips, and one was strengthened with a bonded FRP strip. The effects of three different strip moduli, different fastener lengths and layouts, and predrilling were examined. Three of the beams strengthened with mechanically attached FRP strips showed strengthening comparable to the beam strengthened with a bonded FRP strip. The same three beams strengthened with mechanically attached FRP strips also showed a greater ductility than the beam strengthened with a bonded FRP strip.

Many countries around the world have tremendous needs to repair and strengthen their transportation infrastructure. Almost everywhere, traffic loads have reached levels largely exceeding design expectations. Northern countries also experience severe winter conditions that are combined with an extensive use of deicing salts and accelerate structural deterioration. In Canada, the extent of deterioration has prompted many authorities, including the federal and provincial governments, to investigate the potential use of fiber-reinforced polymer products to extend the life of their existing structures. However, it is widely recognized that the large-scale implementation of these products is often impaired by the lack of data on their durability. This paper presents an experimental project undertaken in order to assess the durability of reinforced concrete beams externally strengthened with two types of carbon-fiber-reinforced polymer (CFRP). The beams were first exposed to either wet-dry cycles or continuous immersion in water and then were loaded in fatigue. Finally, they were tested quasi-statically under four-point bending up to failure. The test results presented here provide some insights on the potential long-term performance of CFRP-strengthened beams exposed to severe environmental conditions.

The behavior under static loading of fiber-reinforced plastic (FRP) retrofitted reinforced concrete beams, possessing a high chloride content and rebar corrosion, was studied both experimentally and analytically. The test beams were characterized as falling into three different groups according to the state of their corrosion damage: (1) natural corrosion, (2) cathodic protection, and (3) accelerated corrosion. The load carrying capacities of the beams, with or without FRP patching, were tested in the laboratory. The experimental results show that the state of corrosion of the steel, the water/cement ratio of the concrete material, and the arrangement and the number of FRP patches all affect the strength as well as the failure mechanisms of retrofitted RC beams. Some simple analytical models and a design concept for retrofitting cracked and corroded RC beams with FRP sheets are also presented and discussed.

This paper presents test results of 18 small-scale reinforced concrete specimens of strengthened beams using carbon-fiber-reinforced polymer (CFRP) composites. The specimens were instrumented with strain gauges in a region where cracks in the concrete were preformed to monitor the variation of strains throughout testing. Results indicate that there can be a very large variation in the measured strains in the composites depending, not only on the location of the cracks, but also on the configuration used to bond the composites to the surface of the elements. The interface shear stresses generated at failure of the beams are compared with two existing analytical models. Additionally, the stress level in the composites was determined for all the strengthened specimens from the experimental data. The calculated stress in the composites reached between 20 and 43% of the CFRP rupture stress. The information presented in this paper provides information that can be used to validate or modify current design procedures of strengthened beams using composites.

A 45-year old, three-span reinforced concrete slab bridge with insufficient capacity was retrofitted with 76.2- and 127-mm wide bonded carbon fiber-reinforced polymer (FRP) plates, 102-mm wide bonded carbon FRP plates with mechanical anchors at the ends, and bonded carbon FRP fabrics. The use of four systems in one bridge provided a unique opportunity to evaluate field installation issues and to examine the long-term performance of each system under identical traffic and environmental conditions. Using controlled truckload tests, the response of the bridge before retrofitting, shortly after retrofitting, and after one year of service was measured. The stiffness of the FRP systems was small in comparison to the stiffness of the bridge deck, and accordingly the measured deflections did not change noticeably after retrofitting. The measured strains suggest participation of the FRP systems, and more importantly, the strength of the retrofitted bridge was increased. A detailed 3D finite-element model of the original and retrofitted bridge was developed and calibrated based on the measured deflections. The model was used to predict more accurately the demands for computing the rating factors. The addition of FRP plates and fabrics led to a 22% increase in the rating factor and corresponding load limits. During a one-year period, traffic loading and environmental exposure did not apparently affect the performance of the FRP systems. The increased capacity and acceptable performance of the FRP systems enabled the engineers to remove the load limits in order to resume normal traffic. Future tests are necessary to monitor the long-term behavior of the FRP systems.

This paper reports on the third phase of a multiphase study undertaken at the American University of Beirut (AUB) to examine the effect of fiber-reinforced polymer (FRP) sheets in confining tension lap splice regions in reinforced concrete beams. Results of the first two phases showed that glass and carbon fiber-reinforced polymer (GFRP and CFRP) sheets were effective in increasing the bond strength and improving the ductility of the mode of failure of tension lap splices in high-strength concrete (HSC) beams with nominal concrete strength of 70 MPa. The experimental results of the two phases were used to propose a new FRP confinement parameter, $K_{\mathrm{tr}\text{,}f}\text{,}$ that accounts for the bond strength contribution of FRP sheets wrapping tension lap splice regions in HSC beams. In this third phase of the AUB study, the trend of the results of phases 1 and 2 and the validity of the analytical model proposed were verified if normal-strength concrete (NSC) is used instead of HSC. Seven beams with nominal concrete strength of 27.58 MPa (4 ksi) were tested in positive bending. Each beam was designed with a tension lap splice in a constant moment region in the midspan of the beam. The main test variables were the configuration (1 strip, 2 strips, or a continuous strip) and the number of layers (1 layer or 2 layers) of the CFRP sheets wrapping the splice region. The test results demonstrated that CFRP sheets were effective in enhancing the bond strength and ductility of failure mode of tension lap splices in NSC in a very similar way to HSC. In addition, the FRP confinement index proposed earlier for HSC was proven to be valid in the case of NSC.

This paper presents the results of a test program for shear strengthening characteristics of continuous unidirectional flexible carbon-fiber polymer sheets bonded to reinforced concrete (RC) beams. A total of eight $150\mathrm{mm}\times 200\mathrm{mm}\times 2\text{,}600\mathrm{mm}$ concrete beams were tested. Various sheet configurations and layouts were studied to determine their effects on ultimate shear strength of the beams. From the tests, it was found that the externally adhesive bonded flexible carbon-fiber sheets are effective in strengthening RC beams in shear. Further, it was observed that the strength increases with the number of sheet layers and the depth of sheets across the beam section. Among the various schemes of wrapping studied, vertical U-wrap of sheet provided the most effective strengthening for concrete beam. Beam strengthened using this scheme showed 119% increase in shear capacity as compared to the control beam without any strengthening. Two prediction models available in literature for computing the shear contribution of carbon-fiber tow sheets to the shear capacity of fiber reinforced polymers bonded beams were compared with the experimental results.

In an effort to assess the constructability and performance of bridges with fiber-reinforced polymer (FRP) composite decks, the short-term and long-term responses of a 207 m, five-span bridge retrofitted with four different FRP panel systems were monitored. The overall aspects of the panel systems, connection details, and construction techniques are presented prior to presentation of the observed and measured responses. Key design parameters (impact factors, girder distribution factors, and level of composite action) for FRP and reinforced concrete decks are evaluated. This paper demonstrates that FRP replacement decks are a viable alternative to reinforced concrete decks and identifies the differences in performances of various FRP deck systems. Two of the FRP panel systems were found to perform considerably better than the other deck systems. Issues that may reduce the service life of FRP deck systems are presented and discussed.

A comparative test program including six beams was carried out. Two strengthening systems, namely hybrid carbon fiber glass fiber-reinforced polymer (H-CF/GF-RP) strengthening and CF-reinforced polymer strengthening were used. The test results showed that the H-CF/GF-RP strengthening led to a significant increase of ductility with a slight influence on stiffness of strengthened beams.