Journal of Performance of Constructed Facilities

The Milwaukee City Hall was built between 1893 and 1898 and is located in downtown Milwaukee, one block east of the Milwaukee River. The $300\mathrm{ft}$ $\left(91.4\mathrm{m}\right)$ long building, nine stories high over its main portion, is a trapezoid in plan. On the south side, there is a $393\mathrm{ft}$ $\left(119.8\mathrm{m}\right)$ tall South Tower located above the main entrance to the building. On three sides, the South Tower rises from the street level to the 13th level and the roof above, and on the north side, it is connected to the rest of the building up to the ninth floor. The South Tower is a hybrid steel and masonry structure consisting of masonry perimeter walls and a central core, four-sided steel truss supporting the floors and roof. The building is a perimeter-load-bearing masonry structure supported on wood piles. The city of Milwaukee had been aware of distress, in the form of cracks and loose masonry, in the South Tower for a number of decades. In 2002, the city took action to investigate the causes and significance of distress, and to develop a repair program. The scope of our work included review of the available structural drawings and documents, inspection of the tower, measurement and monitoring of movements, monitoring of thermal response, structural analyses of the hybrid steel and masonry structure, and development of repair recommendations. The repair program presently is under construction. This paper describes the monitoring program, analyses of the causes for distress, and the implemented repair concepts for the observed distress in the South Tower of the Milwaukee City Hall.

The primary objective of in-situ load testing is to assess the safety and serviceability of an existing structural system with respect to a particular load effect. At this time, the most appropriate loading level and procedure, as well as the associated evaluation criteria are being reconsidered in light of technological advances in construction methods, analytical tools, and monitoring instrumentation. The in-situ load test method for reinforced concrete systems described in the ACI Building Code Requirements for Structural Concrete, namely the 24–h load test method and its evaluation criteria, has been in use for several decades, but may no longer serve the needs of contemporary construction and engineering practices. As a result, other load test methodologies and associated evaluation criteria are under development. This paper and a companion paper describe the rationale and application of an alternative approach to the determination of load level, loading procedure, instrumentation requirements, evaluation criteria and outcomes for two field projects. The first case study is relative to a posttensioned concrete slab where many areas were characterized by tendon and reinforcement misplacement, resulting in inadequate flexural strength and inadequate shear/flexure transfer at column/slab intersections. The second case study is the structural evaluation of a typical floor bay of a two-way reinforced concrete slab system, presenting distributed cracking at the positive and negative moment regions. Finite-element-method models were created for both structures to aid the load test design. The numerical models validated the field observations.

The primary objective of in-situ load testing is to evaluate the safety and serviceability of an existing structural system with respect to a particular load condition and effect. In light of technological advances in construction methods, analytical tools and monitoring instrumentation, new different evaluation criteria are being proposed in addition to different in-situ load test methods. Some criteria may be more appropriate than others based on the expected damage and failure mechanisms of the structure being considered. The companion paper describes the rationale and application of both a consolidated and an alternative approach to the determination of load level, loading procedure and instrumentation requirements for two case studies. This paper discusses in detail the evaluation criteria and outcomes of these two field projects consisting of a posttensioned concrete slab with structural deficiencies due to tendon and mild reinforcement misplacement and a floor bay of a two-way reinforced concrete slab showing cracking at the positive and negative moment regions. After discussing the relative merits of the evaluation methodologies and the significance of their respective acceptance thresholds, concepts for the development of a new global criterion are discussed.

In the last years an increasing interest has been devoted to all the topics related to the security and safety of people. Particular attention has been paid to health monitoring of large civil structures hosting many people, such as high-rise buildings and stadiums. Some extraordinary events, such as the Millennium Bridge oscillations in London, excited by pedestrians, or the Bruce Springsteen concert at the Ullevi Stadium in which coordinated jumps from the crowd caused serious damage to the structure, and drew attention toward a deeper and more careful study of all those problems related to the dynamic behavior of civil structures and their interaction with crowds. Research on these topics is also aimed, among others, at developing techniques allowing for a continuous monitoring of the structure, starting from a set of measurements that can be performed continuously, $24\mathrm{h}$ a day, without the need to stop the structure's functionality. The vast scientific literature confirms the possibility of relating structural health to the evolution of modal parameters, often reaching the aim of localizing any eventual damage, a task otherwise impossible with different techniques. This paper shows part of a long lasting project involving Politecnico di Milano in the setting up of a permanent health monitoring system at the G. Meazza Stadium in Milan. The aim of this project was the evaluation of the actual health state of the structures constituting the stands of the stadium and the deployment of a permanent monitoring system to record the vibration levels reached in all substructures during each event. Evaluation of the actual structure condition was performed by the use of ambient vibration, which was also checked against traditional experimental modal analysis, performed by using an inertial force given by a hydraulic actuator and a detailed measurement mesh. This offered the chance to exploit all possible information concerning natural frequencies, modal shapes, and damping factors. This task is extremely time consuming and expensive, therefore, it cannot be repeated very often. The possibility of using the data coming from the permanent monitoring system, which is about to be installed, is then an attractive perspective to improve structural diagnosis. It is expected that using operational modal analysis techniques will mean knowledge of the excitation applied to the structure will not be required. The parameter estimation obtained by this technique is usually affected by a spread, given both by the uncertainty of the adopted identification techniques and the influence of external parameters, such as crowd loading or temperature. As damage identification is related to changes of the modal parameters, the evaluation of their normal spread is fundamental to fix a threshold in order to identify possible worrysome situations. This paper deals with the identification of the spread in the modal parameter estimation of one of the grandstands of the so-called $3°$ ring of the G. Meazza Stadium in Milan, performed analyzing data collected over more than one year. Vibration data have been recorded during different events, such as soccer matches and concerts. The considered data came from a set of sensors similar to that which is to be installed for the permanent monitoring system, to check about the possibility to use the monitoring system as a diagnostic tool for the structure. A study was also carried out to identify critical aspects in the sensors’ choice and their placement, in order to provide useful information about the design of the permanent monitoring system. The presented results can be used to determine confidence intervals out of which changes in the modal properties can be considered anomalous, and so, worthy of being deeply investigated to assess structural integrity.

Studies have shown that experimentally determined dynamic properties can be used to identify the characteristics of a structure. In this paper, a damage detection technique is developed and demonstrated using system identification, finite-element modeling, and a modal update process. The proposed approach, SFM, provides a rapid estimate of damage locations and magnitudes. The proposed methodology is applied to three case studies. The first is a numerical simulation using computer generated data. The second is an ASCE benchmark problem for structural health monitoring, where the results can be compared to other researchers. The third is a full-scale highway bridge that was field tested using a forced vibration shaking machine. In this case study, the bridge was shaken in several states of damage and the proposed methodology was utilized to detect and determine the location and extent of the damage. It was found that, using the collected data, the SFM approach was able to consistently predict the location of damage as well as estimate the magnitude of the damage.

A large number of corrugated metal pipe-arch culverts are located under highways. This study investigates the field performance of four existing pipe-arch culverts under static and dynamic loads. Effects of various parameters were considered in selection of the culverts, including backfill height, loading conditions, age of placement, and culvert geometry. Static loads were applied at ten different locations above each culvert using heavily loaded test trucks. Six dynamic tests were conducted at speeds varying from 8 to $64\mathrm{km}∕\mathrm{h}$ . A portable instrumentation frame was installed inside each test culvert to monitor the deflections at five critical locations. During each test, strains were also measured using 14 strain gauges. Test results indicated that culvert response was influenced significantly by the backfill height. Nearly symmetrical deflection patterns were recorded for symmetrical loading about the longitudinal vertical plane through the crown. The maximum static deflections were larger than the maximum dynamic deflections for each culvert.

The passage of overloads that require special permitting is a common occurrence. Prior to the passage of such an overload, a simplified computer analysis is generally conducted to predict the expected behavior of the bridge. This paper addresses the field evaluation of three superloads that crossed the Bonnet Carré Spillway Bridge in Louisiana. Emphasis is placed on comparisons between the expected and actual behavior due to rotational restraint, live load distribution, the stiffening effect of bridge rails, and other factors. Finite-element modeling was conducted and the approach taken along with the results obtained are described. One important conclusion was that the longitudinal configuration of the axle loads supplied by the hauler was configured differently than indicated on the permit. While the gross load was accurate, the distribution between sets of axles varied considerably from those assumed in the permitting process. To minimize the potential for damage to bridges it is therefore recommended that axle loads be weighed prior to the passage of such overloads.

Fiber optic sensing technologies are emerging as valid alternatives for the health monitoring of civil structures. Distributed sensors based on Brillouin scattering add the unique capability of measuring strain and temperature profiles along optical fibers. Measurement is performed by establishing the correlation between fiber strain and temperature, and the frequency shift of the Brillouin backscattered light induced by a monochromatic light pulse. The technology holds potential for use on large structures and integrated transportation infrastructure. Its effectiveness has been assessed through scaled laboratory experiments, whereas field validation is limited to very few demonstration projects conducted to date. This paper presents a pilot application of Brillouin optical time domain reflectometry to measure strain profiles along the steel girders of a continuous slab-on-girder bridge subjected to diagnostic load testing. One of the exterior continuous girders required heat-straightening after falling during construction due to wind. The significance of applying a distributed measurement technique lies in the potential to assess the global girder response, which would be impractical and uneconomical using discrete measurement techniques. A $1.16\mathrm{km}$ long sensing circuit was installed onto the web of four girders. The circuit comprises bare optical fiber sensors, and a novel adhesively bonded fiberglass tape with embedded sensing fibers for strain measurement and thermal compensation. The strain profiles were first converted into deflection profiles and validated against discrete deflection measurements performed with a high-precision total station system. Structural assessment based on comparison of the strain profiles with the results of three-dimensional finite-element analysis of the bridge superstructure, and with specification mandated criteria, indicated that the response of the girder under investigation was within the design limits, and did not pose serviceability concerns. Factors that may affect measurement accuracy are finally discussed on the basis of the experimental and numerical results.