Distributed Strain Measurement in Steel Bridge with Fiber Optic Sensors: Validation through Diagnostic Load Test
Publication: Journal of Performance of Constructed Facilities
Volume 22, Issue 4
Abstract
Fiber optic sensing technologies are emerging as valid alternatives for the health monitoring of civil structures. Distributed sensors based on Brillouin scattering add the unique capability of measuring strain and temperature profiles along optical fibers. Measurement is performed by establishing the correlation between fiber strain and temperature, and the frequency shift of the Brillouin backscattered light induced by a monochromatic light pulse. The technology holds potential for use on large structures and integrated transportation infrastructure. Its effectiveness has been assessed through scaled laboratory experiments, whereas field validation is limited to very few demonstration projects conducted to date. This paper presents a pilot application of Brillouin optical time domain reflectometry to measure strain profiles along the steel girders of a continuous slab-on-girder bridge subjected to diagnostic load testing. One of the exterior continuous girders required heat-straightening after falling during construction due to wind. The significance of applying a distributed measurement technique lies in the potential to assess the global girder response, which would be impractical and uneconomical using discrete measurement techniques. A long sensing circuit was installed onto the web of four girders. The circuit comprises bare optical fiber sensors, and a novel adhesively bonded fiberglass tape with embedded sensing fibers for strain measurement and thermal compensation. The strain profiles were first converted into deflection profiles and validated against discrete deflection measurements performed with a high-precision total station system. Structural assessment based on comparison of the strain profiles with the results of three-dimensional finite-element analysis of the bridge superstructure, and with specification mandated criteria, indicated that the response of the girder under investigation was within the design limits, and did not pose serviceability concerns. Factors that may affect measurement accuracy are finally discussed on the basis of the experimental and numerical results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support from the Missouri Dept. of Transportation and the Univ. of Missouri-Rolla Univ. Transportation Center on Advanced Materials and NDT Technologies is gratefully acknowledged. Special thanks are due to Leica Geosystems, Inc., Isaberg Rapid, Pirelli Cavi e Sistemi S.p.A., SEAL S.p.A., Yokogawa Corp. of America, Rolla Technical Institute-Machine Technology and Precision Manufacturing, and Strongwell Corp., industry member of the NSF Industry/University Cooperative Research Center “Repair of Buildings and Bridges with Composites” , for providing precious technical and logistic assistance, materials, and equipment.
References
AASHTO. (2004). Load and resistance factor design (LRFD) bridge design specifications, 3rd Ed., Washington, D.C.
Ahn, I. S., Chiewanichakorn, M., Chen, S. S., and Aref, A. J. (2004). “Effective flange width provisions for composite steel bridges.” Eng. Struct., 26(12), 1843–1851.
Amadio, C., and Fragiacomo, M. (2002). “Effective width evaluation for steel-concrete composite beams.” J. Constr. Steel Res., 58(3), 373–388.
American Concrete Institute (ACI). (2005). “Building code requirements for structural concrete.” ACI318-05, Farmington Hills, Mich.
Bastianini, F., Cargnelutti, M., Di Tommaso, A., and Toffanin, M. (2003). “Distributed Brillouin fiber optic strain monitoring applications in advanced composite materials.” Proc. SPIE, 5057, 478–485.
Bastianini, F., Corradi, M., Borri, A., and Di Tommaso, A. (2005a). “Retrofit and monitoring of an historical building using ‘smart’ CFRP with embedded fibre optic Brillouin sensors.” Constr. Build. Mater., 19(7), 525–535.
Bastianini, F., Matta, F., Galati, N., and Nanni, A. (2005b). “A Brillouin smart FRP material and a strain data post processing software for structural health monitoring through laboratory testing and field application on a highway bridge.” Proc. SPIE, 5765, 600–611.
Bastianini, F., Rizzo, A., Deza, U., Galati, N., and Nanni, A. (2005c). “Discontinuous Brillouin strain monitoring of small concrete bridges: Comparison between near-to-surface and ‘smart’ FRP fiber installation techniques.” Proc. SPIE, 5765, 612–623.
Brillouin, L. (1922). “Diffusion de la lumière et des rayons X par un corps transparent homogéne—Influence de l’agitation thermique.” Ann. Phys. (Paris), 17, 88–122.
Casas, J. R., and Cruz, P. J. S. (2003). “Fiber optic sensors for bridge monitoring.” J. Bridge Eng., 8(6), 362–373.
Chung, W., and Sotelino, E. D. (2006). “Three-dimensional finite-element modeling of composite girder bridges.” Eng. Struct., 28(1), 63–71.
Conner, S., and Huo, X. S. (2006). “Influence of parapets and aspect ratio on live-load distribution.” J. Bridge Eng., 11(2), 188–196.
Eamon, C. D., and Nowak, A. S. (2002). “Effects of edge-stiffening elements and diaphragms on bridge resistance and load distribution.” J. Bridge Eng., 7(5), 258–266.
Fujihashi, K., Uehara, H., Okutsu, M., and Komatsu, K. (2003). “Development of a road disaster monitoring system using optical fiber sensing technology.” NTT Tech. Rev., 1(9), 48–52.
Horiguchi, T., Kurashima, T., and Tateda, M. (1989). “Tensile strain dependence of Brillouin frequency shift in silica optical fibers.” IEEE Photonics Technol. Lett., 1(5), 107–108.
Kihara, M., Hiramatsu, K., Shima, M., and Ikeda, S. (2002). “Distributed optical fiber strain sensor for detecting river embankment collapse.” IEICE Trans. Electron., E85-C(4), 952–960.
Komatsu, K., Fujihashi, K., and Okutsu, M. (2002). “Application of optical sensing technology to the civil engineering field with optical fiber strain measurement device (BOTDR).” Proc. SPIE, 4920, 352–361.
Kurashima, T., Horiguchi, T., and Tateda, M. (1990). “Thermal effects of Brillouin gain spectra in single-mode fibers.” IEEE Photonics Technol. Lett., 2(10), 718–720.
Li, H.-N., Li, D.-S., and Song, G.-B. (2004). “Recent applications of fiber optic sensors to health monitoring in civil engineering.” Eng. Struct., 26(11), 1647–1657.
Mabsout, M. E., Tarhini, K. M., Frederick, G. M., and Kobrosly, M. (1997). “Influence of sidewalks and railings on wheel load distribution in steel girder bridges.” J. Bridge Eng., 2(3), 88–96.
Matta, F., Vath, M., Galati, N., and Nanni, A. (2005). “Modular frame concept cart for inspection of slab-on-girder bridge superstructure.” Proc., 5th Int. Conf. on Bridge Management, G. A. R. Parke and P. Disney, eds., Thomas Telford, London, 187–194.
Missouri Dept. of Transportation (MoDOT). (2002). Bridge design manual, Jefferson City, Mo.
Murayama, H., Kageyama, K., Naruse, H., Shimada, A., and Uzawa, K. (2003). “Application of fiber-optic distributed sensors to health monitoring for full-scale composite structures.” J. Intell. Mater. Syst. Struct., 14(1), 3–13.
Naruse, H., Uchiyama, Y., Kurashima, T., and Unno, S. (2000). “River levee change detection using distributed fiber optic strain sensor.” IEICE Trans. Electron., E83-C(3), 462–467.
Ohno, H., Naruse, H., Kurashima, T., Nobiki, A., Uchiyama, Y., and Kusakabe, Y. (2002). “Application of Brillouin scattering-based distributed optical fiber strain sensor to actual concrete piles.” IEICE Trans. Electron., E85-C(4), 945–951.
Shi, B., Xu, H., Chen, B., Zhang, D., Ding, Y., Cui, H., and Gao, J. (2003). “Feasibility study on the application of fiber-optic distributed sensors for strain measurement in the Taiwan Strait Tunnel project.” Mar. Geotech., 21(3–4), 333–343.
Strand7 Pty Ltd. (2005). “Using Strand7—Introduction to the Strand7 finite-element analysis system.” Strand7 Pty Ltd., Sydney, Australia, 292.
Thévenaz, L., Niklès, M., Fellay, A., Facchini, M., and Robert, P. (1998). “Truly distributed strain and temperature sensing using embedded optical fibers.” Proc. SPIE, 3330, 301–314.
Uttamchandani, D. (1994). “Fibre-optic sensors and smart structures: Developments and prospects.” Electron. Commun. Eng. J., 6(5), 237–246.
Wolf, P. R. (2002). “Surveying and mapping: History, current status, and future projections.” J. Surv. Eng., 128(3), 79–107.
Wu, Z., Xu, B., Hayashi, K., and Machida, A. (2006). “Distributed optic fiber sensing for a full-scale PC girder strengthened with prestressed PBO sheets.” Eng. Struct., 28(7), 1049–1059.
Yasue, N., Naruse, H., Masuda, J., Kino, H., Nakamura, T., and Yamaura, T. (2000). “Concrete pipe strain measurement using optical fiber sensor.” IEICE Trans. Electron., E83-C(3), 468–474.
Information & Authors
Information
Published In
Copyright
© 2008 American Society of Civil Engineers.
History
Received: Oct 25, 2007
Accepted: Mar 31, 2008
Published online: Aug 1, 2008
Published in print: Aug 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.