Journal of Composites for Construction

The results of testing two simply and three continuously supported concrete beams reinforced with glass fiber-reinforced polymer (GFRP) bars are presented. The amount of GFRP reinforcement was the main parameter investigated. Over and under GFRP reinforcements were applied for the simply supported concrete beams. Three different GFRP reinforcement combinations of over and under reinforcement ratios were used for the top and bottom layers of the continuous concrete beams tested. A concrete continuous beam reinforced with steel bars was also tested for comparison purposes. The experimental results revealed that over-reinforcing the bottom layer of either the simply or continuously supported GFRP beams is a key factor in controlling the width and propagation of cracks, enhancing the load capacity, and reducing the deflection of such beams. Comparisons between experimental results and those obtained from simplified methods proposed by the ACI 440 Committee show that ACI 440.1R-06 equations can reasonably predict the load capacity and deflection of the simply and continuously supported GFRP reinforced concrete beams tested.

For members with no transverse reinforcement, numerous models have been proposed for determining shear capacity, most often based on a statistical curve fit to experimental beam test results. The shear provisions of the Canadian code (CSA) for steel-reinforced concrete, by contrast, are based on a theoretical model, the modified compression field theory. This paper demonstrates that the CSA shear provisions for steel-reinforced members can be safely applied to members with internal fiber-reinforced polymer (FRP) bars by adjusting the term $E_s{A}_s$ in the method to $E_r{A}_r$ . A database of 146 shear failures of specimens reinforced with carbon, glass, or aramid FRP or steel is presented and gives an average test to predicted ratio of 1.38 with a coefficient of variation (COV) of 17.2%. The CSA code equations were optimized for the typical strain range of steel-reinforced concrete and when an equation appropriate for the wider range of strains associated with FRP is used, then a better statistical result can be achieved. Application of this expression to the database resulted in an average test to predicted strength ratio of 1.15 with a COV of 14.9%. As both methods are based on a theoretical shear model that was derived for steel-reinforced concrete and since both methods work safely, it can be concluded that the use of internal FRP bars does not change the one-way shear behavior of reinforced concrete beams and slabs without stirrups.

Concrete columns requiring strengthening intervention always contain a certain percentage of steel hoops. Applying strips of wet layup carbon fiber-reinforced polymer (CFRP) sheets inbetween the existent steel hoops might, therefore, be an appropriate confinement technique with both technical and economic advantages, when full wrapping of a concrete column is taken as a basis of comparison. To assess the effectiveness of this discrete confinement strategy, circular cross-sectional concrete elements confined by distinct arrangements of strips of CFRP sheet are submitted to a direct compression load up to the failure point. The influence of the width of the strip, distance between strips, number of CFRP layers per strip, CFRP stiffness, and concrete strength class on the increase of the load carrying capacity and ductility of concrete columns, is evaluated. An analytical model is developed to predict the compressive stress-strain relationship of concrete columns confined by discrete and continuous CFRP arrangements. The main results of the experimental program are presented and analyzed and used to assess the model performance.

Composite materials are being used with notable effectiveness to increase and upgrade the flexural load carrying capacity of reinforced concrete (RC) members. Near-surface mounted (NSM) is one of the most promising strengthening techniques, based on the use of carbon fiber-reinforced polymer (CFRP) laminates. According to NSM, the laminates are fixed with epoxy based adhesive into slits opened into the concrete cover on the tension face of the elements to strength. Laboratory tests have shown that the NSM technique is an adequate strengthening strategy to increase the flexural resistance of RC slabs. However, in RC slabs of low concrete strength, the increase of the flexural resistance that NSM can provide is limited by the maximum allowable compressive strain in the compressed part of the slab, in order to avoid concrete crushing. This restriction reduces the effectiveness of the strengthening, thus limiting the use of the NSM technique. A new thin layer of concrete bonded to the existing concrete at the compressed region is suitable to overcome this limitation. Volumetric contraction due to shrinkage and thermal effects can induce uncontrolled cracking in the concrete of this thin layer. Adding steel fibers to concrete [steel fiber-reinforced concrete (SFRC)], the postcracking residual stress can be increased in order to prevent the formation of uncontrolled crack patterns. In the present work, the combined strengthening strategy, a SFRC overlay and NSM CFRP laminates, was applied to significantly increase the flexural resistance of existing RC slabs. Experimental results of four-point bending tests, carried out in unstrengthened and strengthened concrete slab strips, are presented and analyzed.

The use of fiber-reinforced polymer (FRP) externally bonded (EB) plates is widely accepted as an efficient and unobtrusive retrofitting technique. FRP near-surface mounted plates are now also gradually gaining acceptance due to their substantial increase in debonding strains over EB plates. However tests have shown that the intermediate crack (IC) debonding resistances of FRP plates can be reduced by their interaction with adjacent parallel plates and with parallel free surfaces, that is the cover; this is often reflected in design rules where the IC debonding resistance of individual plates depends on the width of the plate as a proportion of the width of the concrete specimen and on the cover. In this paper, 22 new pull tests are reported that study the IC debonding interaction with adjacent plates and cover. The results are encouraging as they show that there is little reduction in the IC debonding resistance until the lateral cover or gap between plates is relatively small.

The presence of a fiber-reinforced polymer (FRP) strengthening material bonded to the tension face of a reinforced concrete beam will restrict but not prevent the opening of intermediate flexural cracks due to applied loading. Test results indicate that displacements at the toe of flexural cracks create stress concentrations at the interface of the FRP laminate and the beam, leading to the development of localized interface cracks that, typically, propagate, under the effect of the load, to join the original flexural cracks and cause delamination of the FRP system. This type of FRP delamination is commonly termed intermediate crack (IC) debonding. In this paper the analytical models published in the literature are reviewed and it was found that these models do not correlate well with measured experimental results. This paper proposes an analytical model that characterizes the interface shear stress based on two distinct sources: (1) the change in the applied moments along the length of the member and (2) stress concentrations at the intermediate cracks. The proposed model is compared to an experimental database and shown to predict extremely well most of the test results reported by other researchers. A parametric study, performed using the proposed model, indicates that the model varies with several important variables that are not captured by most of the existing models.

Bonding between fiber-reinforced polymer (FRP) sheets and concrete supports is essential in shear and flexural applications for transfer of stress between concrete structure and reinforcement. This paper aims at better understanding FRP–concrete bond behavior and at assessing some of the common formulations for effective bond length and bond–slip models $\left(\tau \text{-}s\right)$ by means of an extensive experimental program on 39 concrete specimens strengthened with various types and amounts of FRP strips and covering a wide range of FRP axial rigidities, subjected to both double-shear and bending tests. Effective bond length, maximum bond/shear stress, slip when bond stress peaks, and slip when bond stress falls to zero, were all experimentally measured. The influence of FRP stiffness on effective bond length and bond–slip behavior was observed. New expressions for (1) effective bond length; (2) maximum shear/bond stress; (3) slip at peak value of bond stress; and (4) slip at ultimate, taking into account the influence of FRP stiffness, are proposed.

This paper presents experimental results and a numerical analysis of the reinforced concrete (RC) beams strengthened in flexure with various externally bonded carbon fiber-reinforced polymer (CFRP) configurations. The aim of the experimental work was to investigate the parameters that may delay the intermediate crack debonding of the bottom CFRP laminate, and increase the load carrying capacity and CFRP strength utilization ratio. Ten rectangular RC specimens with a clear span of $4.2\mathrm{m}$ , categorized in two series, were tested to evaluate the effect of using the additional U-shaped CFRP systems on the intermediate crack debonding of the bottom laminate. Two different configurations of the additional systems were proposed, namely, continuous U-shaped wet layup sheets and spaced side-bonded CFRP L-shaped laminates. The fiber orientation effect of the side-bonded sheets was also investigated. A numerical analysis using an incremental nonlinear displacement-controlled 3D finite-element (FE) model was developed to investigate the flexural and CFRP/concrete interfacial responses of the tested beams. The finite-element model accounts for the orthotropic behavior of the CFRP laminates. An appropriate bond-slip model was adopted to characterize the behavior of the CFRP/concrete interface. Comparisons between the FE predictions and experimental results show very good agreement in terms of the load-deflection and load-strain relationships, ultimate capacities, and failure modes of the beams.

A large number of timber bridges are at the end of their service life in North America and the prohibitive costs of replacement make owners face the challenge of developing efficient rehabilitation techniques. This paper presents the results from an experimental program of testing old full scale timber stringers with longitudinal splits. Stringers were reinforced for shear and bending using glass fiber-reinforced polymer (GFRP) sheets. A total of nine full-scale Douglas-fir beams were tested in three-point bending after strengthening for flexure and shear with GFRP sheets. Horizontal shear forces in shear reinforcement were calculated using a simplified model. Beams that failed by debonding of shear reinforcement, failed at horizontal shear forces within the range of $150–266\mathrm{kN}$ . Design charts were constructed on the basis of these calculated forces to simplify the design of shear reinforcement for different sizes and locations of splits.

Fiber-reinforced polymer (FRP) hollow tubes are used in structural applications, such as utility poles and pipelines. Concrete-filled FRP tubes (CFFTs) are also used as piles and bridge piers. Applications such as poles and marine piles are typically governed by cyclic bending. In this paper, the fatigue behavior of glass-FRP filament-wound tubes is studied using coupons cut from the tubes. Several coupon configurations were first examined in 24 tension and five compression monotonic loading tests. Fatigue tests were then conducted on 81 coupons to examine several parameters; namely, loading frequency as well as maximum-to-ultimate $({\sigma }_{\max }∕{\sigma }_{\mathrm{ult}})$ and minimum-to-maximum $({\sigma }_{\min }∕{\sigma }_{\max })$ stress ratios, including tension tension and tension compression, to simulate reversed bending. The study demonstrated the sensitivity of test results and failure mode to coupon configuration. The presence of compression loads reduced fatigue life, while increasing load frequency increased fatigue life. Stiffness degradation behavior was also established. To achieve at least one million cycles, it is recommended to limit $({\sigma }_{\max }∕{\sigma }_{\mathrm{ult}})$ to 0.25. Models were used to simulate stiffness degradation and fatigue life curve of the tube. Fatigue life predictions of large CFFT beams showed good correlation with experimental results.

A fiber-reinforced polymer (FRP) composite cellular deck system was used to rehabilitate a historical cast iron thru-truss structure (Hawthorne St. Bridge in Covington, Va.). The most important characteristic of this application is reduction in self-weight, which raises the live load-carrying capacity of the bridge by replacing the existing concrete deck with a FRP deck. This bridge is designed to HL-93 load and has a $22.86\mathrm{m}$ clear span with a roadway width of $6.71\mathrm{m}$ . The panel-to-panel connections were accomplished using full width, adhesively (structural urethane adhesive) bonded tongue and groove splices with scarfed edges. To ensure proper construction, serviceability, and strength of the splice, a full-scale two-bay section of the bridge with three adhesively bonded panel-to-panel connections was constructed and tested in the Structures Laboratory at Virginia Tech. Test results showed that no crack initiated in the joints under service load and no significant change in stiffness or strength of the joint occurred after 3,000,000 cycles of fatigue loading. The proposed adhesive bonding technique was installed in the bridge in August 2006.