Journal of Composites for Construction

Fiber-reinforced polymer (FRP) application is a very effective way to repair and strengthen structures that have become structurally inefficient over their life span. This paper investigates the applicability of existing models for the prediction of debonding failure in RC beams externally strengthened with FRP. It is very important to predict the limit at which FRP debonds from the beam in order to arrest premature failures. The existing models lack the thoroughness of bond predictability. This is mainly due to the development models on the basis of small amount of tested data. Hence, there is a need to compare the existing work to an extensive database of strengthened beams. Existing experimental work was collected from literature to create a database of 163 beams tested in three point and four point bending tests. Various models are applied to this database and behavior of each model is analyzed using statistical parameters and degree of uncertainty in prediction.

The technique of bonding fiber-reinforced plastic (FRP) plates on the tensile side of concrete members has been proved to be an effective method for structural strengthening. For a RC beam strengthened with FRP plates, failure may occur by concrete cover separation near the plate end, or crack-induced debonding initiated by an opening crack away from the plate end. Experimental investigations have shown that tapering of the FRP plate at its ends is effective in reducing the stress concentrations and increasing the loading for plate end failure to occur. However, with reduced averaged thickness of the tapered plate, crack-induced debonding is also easier to occur. To optimize plate tapering in practical designs, an approach to analyze crack-induced debonding of tapered FRP plates is required. In the present investigation, FRP debonding is first studied with the finite-element method. In the analysis, a three-parameter model is employed for the shear slip relation between concrete and the FRP plate. Based on the findings from FEM analysis, simplifying assumptions are derived and an analytical model is developed for calculating the stresses in the FRP plate and along the concrete-to-FRP interface. The analytical stress distributions show good agreement with those from the FEM analysis. Using the analytical model, the effect of FRP tapering is quantitatively assessed. Also, the effects of various parameters on the ultimate failure load are simulated.

Four prestressed concrete beams were constructed and tested to investigate the effectiveness of flexural post-strengthening with prestressed carbon fiber-reinforced polymer (CFRP) strips. One of the beams served as a reference beam, another was bonded with an unstressed CFRP strip, and the remaining two specimens were strengthened with prestressed CFRP strips at two prestressing levels. The gradient method was used for the anchorage of the prestressed CFRP strips. Experimental and analytical calculations are compared with the test results. Further, different failure modes are explained. On the basis of this investigation, recommendations for the use of prestressed CFRP strips anchored with the gradient method are given.

This paper presents a novel anchoring technique for strengthening reinforced concrete beams with prestressed carbon fiber- reinforced polymer (CFRP) sheets. Permanent steel anchors are commonly used for the application of prestressed CFRP sheets. The steel anchors are, however, susceptible to corrosion and may not blend into the aesthetics of the original structure. As a result, it may be preferable to remove the steel anchors after transferring the required prestress to the structure with minimal losses of sustained prestress. A technique for replacing the steel anchors with nonmetallic anchors is investigated and reported herein. Nine doubly reinforced concrete beams are tested with various types of nonmetallic anchor systems such as nonanchored U-wraps, mechanically anchored U-wraps, and CFRP sheet-anchored U-wraps. The developed nonmetallic anchorages successfully transfer the sustained prestress in the CFRP sheets with insignificant prestress losses. A closed-form solution for the transfer of prestress is developed and compared to the experimental results.

This paper presents the flexural behavior of reinforced concrete beams strengthened with prestressed carbon fiber-reinforced polymer (CFRP) sheets using nonmetallic anchor systems. The developed nonmetallic anchor systems replace the permanent steel anchorage. Nine doubly reinforced concrete beams are tested with various types of nonmetallic anchor systems such as nonanchored U-wraps, mechanically anchored U-wraps, and CFRP sheet-anchored U-wraps. The flexural behavior of the tested beams, including detailed failure modes of each nonmetallic anchor system, is investigated. The study shows that the developed nonmetallic anchors are more effective in resisting peeling-off cracks compared to the permanent steel anchors and the beams strengthened with the nonmetallic anchors provide comparable load-carrying capacity with respect to the steel anchored control beam.

Jacketing is less effective to large square/rectangular RC columns due to the inability of the rectangular-shaped jacket in restraining the dilation of concrete in the middle of a straight side. A new retrofit method is proposed in this work by fiber reinforcing the surface concrete in the middle of a straight side. Fiber reinforcing is achieved by inserting small fiber-reinforced polymer (FRP) bars into the concrete in the plastic hinge zone. The inserted FRP bars act as horizontal reinforcement to increase the ductility of the concrete in a similar way as that in normal fiber-reinforced concrete. When this fiber reinforcing technique is combined with the conventional jacketing, the concrete in all parts of a cross section may be effectively confined. In this work, experimental tests were undertaken to investigate the effectiveness of this new retrofit technique. Six half-scaled columns were tested and the test results demonstrated the effectiveness of the method.

Numerous research studies have shown externally bonded fiber-reinforced polymer (FRP) materials can be used efficiently and economically to repair and retrofit deteriorated or understrength concrete structures. FRP materials are being widely applied in the rehabilitation of deteriorated bridges, however, their use in buildings has been limited, partly because of insufficient knowledge about the performance of FRP materials in fire. To enable further applications of FRPs in buildings, this paper presents a study on the residual performance after fire of four reinforced-concrete (RC) T-beams that were prestrengthened with externally bonded FRP sheets and provided with a supplemental fire protection system. Results from this study suggest that the RC beams strengthened with FRPs prior to fire exposure retained most of their initial unstrengthened flexural capacity after fire. This is attributed to the fact that the temperature of the internal concrete and reinforcing steel was kept to below 200 and $593°\mathrm{C}$ , respectively.

In 2003, an experimental research program was initiated at the American University of Beirut with the objectives of (1) evaluating the effectiveness of external fiber-reinforced polymer (FRP) confinement in improving the bond strength of spliced reinforcement in reinforced-concrete (RC) columns and its implications on the lateral load capacity and ductility of the columns under seismic loading; and (2) establishing rational design criteria for bond strengthening of spliced reinforcement using external FRP jackets. This paper presents a discussion of recent experimental results dealing with rectangular columns and the results of a pilot study conducted on circular columns with particular emphasis on aspects related to the bond strength of the spliced column reinforcement. A nonlinear analysis model is developed for predicting the envelope load–drift response, taking into account the effect of FRP confinement on the stress–strain behavior of concrete in compression. Results predicted by the model showed excellent agreement with the test results. Design expressions of the bond strength of spliced bars in FRP-confined concrete were assessed against the current experimental data, and a criterion for seismic FRP strengthening of bond-critical regions in RC members is proposed.

Current international design guidelines provide predictive design equations for the strengthening of reinforced concrete (RC) columns of both circular and prismatic cross sections by means of fiber-reinforced polymer (FRP) confinement and subjected to pure axial loading. Extensive studies (experimental and analytical) have been conducted on columns with circular cross sections, and limited studies have been conducted on members with noncircular cross sections. In fact, the majority of available research work has been on small-scale, plain concrete specimens. In this review paper, four design guidelines are introduced, and a comparative study is presented. This study is based on the increment of concrete compressive strength and ductility and includes the experimental results from six RC columns of different cross-sectional shapes. The observed outcomes are used to identify and remark upon the limits beyond the ones specifically stated by each of the guides and that reflect the absence of effects not considered in current models. The purpose of this study is to present a constructive critical review of the state-of-the-art design methodologies available for the case of FRP-confined concrete RC columns and to indicate a direction for future developments.

This paper presents a finite-element analysis study of elliptical concrete columns, converted from rectangular cross sections and confined with carbon fiber-reinforced polymers (CFRP) through an enhancement/strengthening procedure, under eccentric loadings. The parameters considered for the finite-element analysis study include various eccentric loads, and the number of CFRP layers as well as their orientation with respect to circumferential axis of concrete columns. Validation of the finite-element model was performed leveraging an experimental study reported in the literature. Study findings suggest that eccentric loading versus concentric loading considerably reduces the efficiency of the CFRP wrapping. The study, however, also shows that it is possible to diminish the adverse effect of eccentric loading through proper adjustment of the wrap configuration, i.e., the number of layers as well as the orientation of the fibers.

Behavior of short and deep beams made of concrete-filled fiber-reinforced polymer (FRP) tubes (CFFT) was compared experimentally to that of their slender counterparts. Ten specimens made from four types of glass FRP tubes with different fiber architecture and lamina lay-up were tested with shear span to depth ratio between 0.9 and 6.25, diameter to thickness ratio between 16 and 63, and reinforcement index between 0.11 and 2.2. The study extended the test database of CFFTs to the lowest practical limit of shear span to depth ratio. None of the CFFT beams tested, even with the lowest shear span to depth ratio of 0.9, failed in shear. Tensile bending strains at the bottom of the midspan section of the beams always remained higher than the respective diagonal tensile strain at the midpoint of the shear span. Web shear cracks were observed only in the concrete core of deep CFFT beams with high reinforcement index. Following the first flexural crack, the concrete core began to slip relative to the FRP tube. This lack of composite action made shear less critical than flexure. Finally, short and deep CFFT beams exhibited higher bending capacity than their slender counterparts, primarily due to the direct diagonal compression strut that develops in the concrete core through arching action.