Journal of Bridge Engineering

The paper presents the calibration procedure and background data for the development of design code provisions for wood bridges. The structural types considered include sawn lumber stringers, glued-laminated girders, and various wood deck types. Load and resistance parameters are treated as random variables, and therefore, the structural performance is measured in terms of the reliability index. The statistical parameters of dead load and live (traffic) load, are based on the results of previous studies. Material resistance is taken from the available test data, which includes consideration of the post-elastic response. The resistance of components and structural systems is based on the available experimental data and finite element analysis results. Statistical parameters of resistance are computed for deck and girder subsystems as well as individual components. The reliability analysis was performed for wood bridges designed according to the AASHTO Standard Specifications and a significant variation in reliability indices was observed. The recommended load and resistance factors are provided that result in consistent levels of reliability at the target levels.

Vertical loads on concrete box culverts under high embankments are examined, where a high embankment is defined herein as one where the height of the fill above the culvert is greater than the width of the culvert. Results from an instrumented culvert are described, with results from pressure cells, strain gages in the wall, and strain gages in the roof showing reasonable agreement. There was strong correlation between the height of fill and the pressure and internal forces in the culvert, suggesting that the soil–structure interaction factor is independent of the $H∕B$ ratio. The results of the instrumented culvert were compared to those of other instrumented culverts under high embankments. The measured roof pressures were significantly greater than the pressure due to the soil overburden, with the measured pressures averaging 1.5 times the soil overburden pressure. Although the soil–structure interaction factor recommended by the American Society of Highway and Transportation Officials specification tends to under-predict the loads acting on concrete culverts, a simplified reliability analysis suggests that the Specification provides a sufficient level of safety.

In design practice, the transverse bending analysis of box-girder bridges is commonly done by modeling the cross section as a frame of unit width with imaginary supports at the web locations. The transverse bending moments obtained from simple frame analysis (SFA) is sometimes increased by a small percentage to accommodate the errors in modeling. In this paper, a large number of simply supported box-girder bridges have been analyzed by both SFA and three-dimensional finite element analysis for different load conditions and wheel contact areas, and the errors in SFA have been studied and quantified. The error is found to vary widely at the web-top flange junction as well as under the load (maximum sagging moment), depending on the eccentricity of loading, the wheel contact dimensions and the web-flange thickness ratio. Accordingly, a set of correction factors to the results of SFA have been proposed, which is expected to be of significant use in design practice. The use of the correction factors is demonstrated by means of two illustrative examples. The scope of the study is limited to the simplest case of a single-cell concrete box-girder bridge (simply supported with end diaphragms) without overhanging flanges.

This paper presents issues in the design concept, analysis, and test results of a harp-shaped single span cable-stayed bridge, Hongshan Bridge, located in Changsha, Hunan Province, China. The bridge has a 206 m span, with a pylon inclined at 58° from the horizontal and 13 pairs of parallel cable stays without a back stay. This paper discusses the design approach for the main components of the bridge. Emphasis will be put on the following three aspects. First, the weight of the pylon and all dead loads of the main girder in addition to part of the live loads must be in a balanced condition. Second, the main girder should be an orthotropic steel-concrete composite box girder because of the superior safety and weight reduction of this type of structure. Third, the cable stays should be anchored at the neutral axis of the pylon to prevent the development of high secondary moments caused by other anchor approaches. Furthermore, based on results from tests carried out on three models, namely, scaled full model tests in a scale of 1:30, scaled section model tests in a scale of 1:6, and wind tunnel tests, the following four key issues were studied: (1) the local stability of orthotropic steel-concrete composite box girder subjected to combined bending and axial loads; (2) the characteristics under loads of 13-m-long cantilever beams; (3) the safety of the bridge under some other dangerous conditions; and (4) the characteristics of wind resistance and wind tunnel testing.

This project examined several uncertainties of integral abutment bridge design and analysis through field-monitoring of an integral abutment bridge and three levels of numerical modeling. Field monitoring data from a Pennsylvania bridge site was used to refine the numerical models that were then used to predict the integral abutment bridge behavior of other Pennsylvania bridges of similar construction. The instrumented bridge was monitored with 64 gages; monitoring pile strains, soil pressure behind abutments, abutment displacement, abutment rotation, girder rotation, and girder strains during construction and continuously thereafter. Three levels of numerical analysis were performed in order to evaluate prediction methods of bridge behavior. The analysis levels included laterally loaded pile models using commercially available software, two-dimensional (2D) single bent models, and 3D finite element models. In addition, a weather station was constructed within the immediate vicinity of the monitored bridge to capture environmental information including ambient air temperature, solar radiation, wind speed and direction, humidity, rainfall, and barometric pressure. Laterally loaded pile models confirmed that inclusion of multilinear soil springs created from $p\text{-}y$ curves is a valid approach for modeling soil–pile interaction within a finite element program. The 2D and 3D numerical models verified the field data indicating that primary accommodation of superstructure expansion and contraction is through rotation of the abutment about its base rather than longitudinal translation, as assumed in the original design of this bridge. Girder axial forces were suspected to be influenced by creep and shrinkage effects in the bridge superstructure. Pile strains were found to be well below strains corresponding to pile plastic moment. Overall, the 2D numerical model and the 3D numerical model predicted very similar behavior.

The use of horizontally curved composite box-girder bridges in modern highway systems has become increasingly popular for economic as well as for aesthetic considerations. Based on a recent literature review on the design of box-girder bridges, it was observed that a simple design method for curved bridges, based on load distribution factors for stresses and shears, is as yet unavailable. This paper presents the results of an extensive parametric study, using a finite element method, in which the structural responses of 240 two-equal-span continuous curved box-girder bridges of various geometries were investigated. The parameters considered in this study included span-to-radius of curvature ratio, span length, number of lanes, number of boxes, web slope, number of bracings, and truck loading type. Based on the data generated from this study, empirical formulas for load distribution factors for maximum longitudinal flexural stresses and maximum deflection due to dead load as well as AASHTO live loading were deduced. An illustrative design example is presented.

In recent years, steel trapezoidal box girders for curved highway interchanges have become popular. For these bridge systems, significant steel girder cross-sectional stresses occur during the concrete casting sequence. To help resist construction loads, a lateral truss system is installed at a level close to the top flanges to form a “pseudo-closed” section, which has a higher torsional stiffness than an open U-section. Several recent incidents, ranging from the buckling of individual bracing members to the complete failure of a trapezoidal box-girder bridge, suggest a lack of understanding of curved box-girder behavior and the use of inadequate analysis tools by designers. In order to provide an improved understanding of these systems, computational software to analyze steel trapezoidal box-girder bridges with a cured or semicured concrete deck has been developed. In this paper, a brief description of this computationally efficient and easy-to-use software is provided. In addition, results are presented from computational studies evaluating the performance of different girder bracing configurations in conjunction with different deck placing sequences. Based on these results, recommendations for design are given.

An experimental study of principal strains and deflections of glass fiber-reinforced polymer (GFRP) composite bridge deck systems is presented. The experimental results are shown to correlate well with those of an analytical model. While transverse strains and vertical deflections are observed to be consistent, repeatable, and predictable, longitudinal strains exhibit exceptional sensitivity to both strain sensor and applied load location. Large, reversing strain gradients are observed in the longitudinal direction of the bridge deck. GFRP deck system geometry, connectivity, material properties, and manufacturing imperfections coupled with the observed strains suggest that the performance of these structures should be assessed under fatigue loading conditions. Recommendations for accurately assessing longitudinal strain in GFRP bridge decks are made, and a review of existing data is suggested.

The application of fiber-reinforced composites (FRP) is gaining momentum as an alternative material for bridge replacement, repair, and rehabilitation. While a number of states now use FRP, a lack of standards, codes, and performance data for FRP bridge decks has resulted in the use of FRP technology not being widely accepted. This paper presents the performance results, based on acoustic emission (AE), of six full-scale glass FRP bridge deck panels with nominal cross-sectional depths varying from 152 mm (6 in.) to 800 mm (30 in.). The objective was to develop for use during in-service field inspections an AE monitoring strategy that will determine the structural performance of the deck. As such, the characterization of damage, e.g., fiber breakage, matrix cracking, and delamination, was part of the investigated criteria and the contributing factors for identification of a monitoring strategy. Although some factors were determined to be associated with the performance evaluation of the structural integrity of the decks, further investigation is needed.

Fiber reinforced polymer (FRP) composite bridge decks are gaining the attention of bridge owners because of their light self-weight, corrosion resistance, and ease of installation. Constructed Facilities Center at West Virginia University working with the Federal Highway Administration and West Virginia Department of Transportation has developed three different FRP decking systems and installed several FRP deck bridges in West Virginia. These FRP bridge decks are lighter in weight than comparable concrete systems and therefore their dynamic performance is equally as important as their static performance. In the current study dynamic tests were performed on three FRP deck bridges, namely, Katy Truss Bridge, Market Street Bridge, and Laurel Lick Bridge, in the state of West Virginia. The dynamic response parameters evaluated for the three bridges include dynamic load allowance (DLA) factors, natural frequencies, damping ratios, and deck accelerations caused by moving test trucks. It was found that the DLA factors for Katy Truss and Market Street bridges are within the AASHTO 1998 LRFD specifications, but the deck accelerations were found to be high for both these bridges. DLA factors for Laurel Lick bridge were found to be as high as 93% against the typical design value of 33%; however absolute deck stress induced by vehicle loads is less than 10% of the deck ultimate stress.

The majority of experimental work involving the flexural retrofit of concrete bridge girders has been conducted on beam specimens with adhesive-applied, soffit-mounted, fiber-reinforced polymer (FRP) composite systems, referred to in this study as conventional adhesive application (CAA). It has been observed that the performance of such girders is often controlled by the quality of the bond between the FRP and the concrete substrate and the substrate’s ability to transfer stress from the steel to the FRP. With the goal of improving the performance of bonded FRP in mind, two additional soffit-mounted retrofit schemes are investigated: near-surface mounted (NSM), where the FRP strips are embedded in adhesive within slots cut into the substrate concrete, and, powder-actuated fastener-applied (PAF) FRP, which uses a powder-actuated nail gun to install mechanical fasteners through predrilled holes in the FRP into the concrete substrate, “nailing” the FRP in place. The PAF application is a recent development, and little work has been done on it other than by the proprietors of the system. This study reports on a comparative study of the static and fatigue performance of reinforced concrete beams retrofitted with CAA, NSM, and PAF FRP retrofit systems. Ten medium-scale beams were tested: six strengthened specimens, two per retrofit method, were tested under cyclic loading conditions, and four specimens, one per retrofit method and one control specimen, were tested monotonically to failure. The results of this study indicate that although all three methods of FRP application result in significant strength increases over the control specimen under monotonic loading conditions, the CAA method is outperformed by the other methods under cyclic conditions. A number of other relevant detailed conclusions with respect to performance and practical application issues are presented for each of the methods of retrofit examined in this study. Significantly, clear evidence of FRP debonding in the midspan region prior to specimen failure is presented.

This paper summarizes comprehensive experimental studies on scaled models of squat bridge columns repaired and retrofitted with advanced composite-material jackets. In the experimental program, a total of 14 half-scale squat circular and rectangular reinforced concrete columns were tested under fully reversed cyclic shear in a double bending configuration. In order to provide a basis for comparison, a total of three as-built columns were tested. Another 10 column samples were tested after being retrofitted with different composite jacket systems. One circular as-built column was repaired after failure. The repair process involved both crack injection as well as addition of carbon/epoxy composite jacket. The repaired column was then retested and evaluated. Experimental results showed that all as-built columns developed an unstable behavior and failed in brittle shear mode. The common failure mode for all retrofitted samples was due to flexure with significant improvement in the column ductility. The repaired column demonstrated ductility enhancement over the as-built sample.

This paper presents an inclusive testing program conducted on scaled models of reinforced concrete (RC) bridge columns with insufficient lap-splice length. Thirteen half-scale circular and square column samples were tested in flexure under lateral cyclic loading. Three columns were tested in the as-built configuration whereas ten samples were tested after being retrofitted with different composite-jacket systems. A brittle failure was observed in the as-built samples due to bond deterioration of the lap-spliced longitudinal reinforcement. The jacketed circular columns demonstrated a significant improvement in their cyclic performance. Yet, tests conducted on square jacketed columns showed a limited improvement in clamping on the lap-splice region and for enhancing the ductility of the column.