Journal of Bridge Engineering

The structural condition assessment of highway bridges is largely based on visual observations described by subjective indices, and it is necessary to develop a methodology for an accurate and reliable condition assessment of aging and damaged structures. This paper presents a method using a systematically validated finite-element model for the quantitative condition assessment of a damaged reinforced concrete bridge deck structure, including damage location and extent, residual stiffness evaluation, and load-carrying capacity assessment. In a trial of the method in a cracked bridge beam, the residual stiffness distribution was determined by model updating, thereby locating the damage in the structure. Furthermore, the damage extent was identified through a defined damage index and the residual load-carrying capacity was estimated.

In this paper, the static and seismic performance of some short span reinforced concrete arch bridges, before and after strengthening interventions, are evaluated. To verify whether retrofit strategies for the considered arch bridges, which were designed for resisting under permanent and service actions, were adequate for earthquake resistance, seismic analyses of the as-built model of the structures have been undertaken. To account for multiple input effects on arches, induced by out-of-phase motions at foundation levels as well as different boundary conditions at structural supports, the seismic response of the structures under correlated horizontal and vertical multiple excitations is calculated. The effects on arch bridges of conventionally used uniform input and partially correlated multiple inputs with phase shifts are compared. In all cases, the results are discussed with particular reference to the influence of structural configuration, secondary systems, cross-section thickness of the arch, and retrofit interventions.

The present paper reports on the results from a series of full-scale experimental tests carried out on concrete-filled steel-grid bridge deck assemblies. The testing focused on assessing the fatigue performance and ultimate strength response of a full-depth-overfilled concrete-filled steel-grid deck configuration. The results from the experimental testing program described herein are compared with the predicted deck responses as per the current AASHTO provisions contained in the LRFD and 16th edition specifications.

This paper describes the feasibility of 1,400 m steel cable-stayed bridges from both structural and economic viewpoints. Because the weight of a steel girder strongly affects the total cost of the bridge, the writers present a procedure to obtain a minimum weight for a girder that ensures safety against static and dynamic instabilities. For static instability, elastoplastic, finite-displacement analysis under in-plane load and elastic, finite-displacement analysis under displacement-dependent wind load are conducted; for dynamic instability, multimodal flutter analysis is carried out. It is shown that static critical wind velocity of lateral torsional buckling governs the dimension of the girder. Finally, the writers briefly compare a cable-stayed bridge with suspension bridge alternatives.

A four-span suspension bridge which has two main 2,000 m spans is investigated with respect to the deformation characteristics. Generally, deformation behavior of the four-span suspension bridge is mainly influenced by rigidity of the center tower. This study is focused on properties such as bending and torsional rigidity of the girder, sag ratio, and dead load. The result of this investigation clarified that the lower rigidity under live load than the three-span bridge is caused by the smaller cable spring coefficient of the main span, which is 1/6 of the side span. Nevertheless, the tendency is stable and can be assisted by stiffened rigidity of the center tower. Live load deflection of the girder can be reduced to less than 1/200 of the main span length, which is useful and economical, by stiffening the bending coefficient of the center tower. Moreover, relatively lower rigidity of the center tower is sufficient for the 2,000 m span suspension bridge than for the 1,000 m span case, keeping the same deflection ratio. Three-dimensional sag geometry of the main cable is effective in limiting the torsional deformation, which is an especially important issue for the four-span suspension bridge caused by twist of the center tower.

The seismic response of typical multispan simply supported (MSSS) and multispan continuous steel girder bridges in the central and southeastern United States is evaluated. Nonlinear time history analyses are conducted using synthetic ground motion for three cities for 475 and 2,475-year return period earthquakes (10 and 2% probability of exceedance in 50 years). The results indicate that the seismic response for the 475-year return period earthquake would lead to an essentially linear response in typical bridges. However, the seismic response for a 2,475-year return period earthquake resulted in significant demands on nonductile columns, fixed and expansion bearings, and abutments. In particular, pounding between decks in the MSSS bridge would result in significant damage to steel bearings and would lead to the toppling of rocker bearings, which may result in unseating of the bridge deck.

Part I of this two-part paper evaluated the seismic response of typical multispan simply supported (MSSS) and multispan continuous steel girder bridges in the central and southeastern United States. The results showed that the bridges were vulnerable to damage resulting from impact between decks, and large ductility demands on nonductile columns. Furthermore, fixed and expansion bearings were likely to fail during strong ground motion. In this paper, several retrofit measures to improve the seismic performance of typical multispan simply supported and multispan continuous steel girder bridges are evaluated, including the use of elastomeric bearings, lead-rubber bearings, and restrainer cables. It is determined that lead-rubber bearings are the most effective retrofit measure for reducing the seismic vulnerability of typical bridges. While isolation provided by elastomeric bearings limits the forces into the columns, the added flexibility results in pounding between decks in the MSSS steel girder bridges. Restrainer cables, which are becoming a common retrofit measure, are effective in reducing the hinge opening in MSSS bridges with steel bearings. However, when used with elastomeric bearings, the restrainer cables negate the isolation effect of the bearings.

Pontesei Dam is a major concrete dam built after World War II across the canyon of Maè Creek (Valle di Zoldo) in the Italian Eastern Alps. Just upstream from the dam, a gully discharges water from steep mountains. The only road serving the dam and the entire valley upstream of the dam runs along the mountainside and crosses the gully. In 1959, an exceptionally rainy season caused a flood, which destroyed the bridge. A temporary Bailey bridge was subsequently built by the army, but in 1990 it was decided to design a new bridge. The main challenges posed to the designer included building the new deck and the abutments underneath the Bailey bridge without disrupting traffic, hoisting the deck just to the bottom of the Bailey bridge, and finally substituting the new deck for the Bailey bridge in one day. Other problems included the instability of the rock mass at the abutments and the gravitative convergence of the two sides of the gully. This paper describes the design, construction, and testing of the bridge replacement and the bridge abutments.

This paper presents a detailed investigation of warping-related stresses in 18 composite steel-concrete box girder bridges. The bridge designs were adapted from blueprints of existing bridges in the state of Florida and encompass a wide range of parameters including horizontal curvature, cross-sectional properties, and number of spans. The bridges after which the analysis prototypes are modeled were designed by different firms and constructed at different times and are considered to be representative of current design practice. Forces are evaluated from analyses that account for the construction sequence and the effect of warping. Loading is considered following the 1998 AASHTO-LRFD provisions. Differences between stresses obtained taking warping into account and those calculated by ignoring warping are used to evaluate the effect of warping. Analysis results show that warping has little effect on both shear and normal stresses in all bridges. Current design provisions are discussed in light of the analysis results.

The superstructure for integral abutment bridges is cast integrally with abutments that are supported by a single row of piles. Thermal expansion or contraction and concrete creep and shrinkage induce bending stresses in the piles. Very limited design and construction guidelines are available and no unified design procedures exist nationwide; hence, there is a lack of enthusiasm to adopt integral abutment bridges for long spans. Current design and construction practices of integral abutment bridges have been reviewed. Important design parameters are identified with an emphasis on temperature, creep, and shrinkage effects of concrete bridge decks, varying soil strata, and the pile-soil interaction. A parametric study is described regarding the effects of a predrilled hole, the type of fill in the predrilled hole, elevation of the water table, soil type, and pile orientation. The results from the parametric study should aid in the selection and design of piles for integral abutment bridges.