Journal of Composites for Construction

Efficient use of pultruded carbon fiber–reinforced plastic profiles (CFRP tendons) to prestress high-performance concrete (HPC) highly depends on the performance of the anchorage system and on material choice. For current applications, a prestressing degree of approximately 40% of the CFRP material strength is utilized in pretensioned concrete elements. A higher prestress implicates lower costs of fully prestressed concrete elements. The present project aimed to optimize the design of a removable and reusable pretensioning anchorage system for sand-coated CFRP rods. The optimized design was achieved by means of finite-element calculations in which parametric studies were complemented with extensive experimental work for validation. Analytical results demonstrated a reduction up to 25% for the relevant stress peaks in the tendons. The static rupture load under laboratory conditions increased by 25%, and the pretensioning level on-site could be increased by 50%. This improvement in production efficiency can be explained by easier applicability of the new system, i.e., failure tolerant assembly and prestressing process.

Research into the use of fiber-reinforced polymers (FRPs) in structures at the Royal Military College of Canada (RMC) during the past two decades has largely focused on two important military engineering goals—mobility and survivability. FRP research in the area of mobility has included the strengthening and repair of reinforced concrete beams and slabs and the development of portable lightweight bridges suitable for most wheeled and tracked vehicles. With respect to survivability, a particular interest is in the use of FRPs to enhance the blast resistance of structural columns and beams. Such research may be equally pertinent to improving the blast resistance of a broad range of critical domestic infrastructure worldwide, given both the increasing concerns about terrorist acts and the desire as well to improve resistance to accidental explosion. This paper will report on the experimental work of two of the most recent FRP research projects carried out at the RMC in support of military objectives—the development of a lightweight portable glass FRP bridge and the use of FRP to strengthen reinforced concrete structural columns against blast. A full-sized FRP box beam was constructed and tested in the laboratory and 28 half-scale reinforced concrete columns, some strengthened with either steel reinforced polymer (SRP) or with FRP, were tested in the field under blast load. From this research, it can be seen that FRP as a structural material offers significant advantages to military forces working in conflict zones, whether for traditional strengthening of damaged or understrength structures, lightweight portable bridge options, or as a means of strengthening structures against blast effects.

Advances in material technology allow for the exploration of new structural forms and systems. In recent years, fiber-reinforced polymers (FRPs) have emerged as candidate materials for civil engineering applications, and the use of FRPs in construction has been an area of growing interest. Unidirectional high-strength FRPs are well-suited for use as tensioning elements, but anchorage details present a challenge. An alternative is to self-anchor the FRP tensioning element by winding thin layers of material around supports and then laminating all the layers together (a laminated strap) or by securing only the outermost layer to form a closed outer loop while the inner layers remain nonlaminated (a nonlaminated strap). Nonlaminated FRP straps have been found to have higher efficiencies than equivalent laminated straps, which is advantageous in high-tension applications. The suitability of nonlaminated FRP straps for use as unbonded tension elements provides scope for use in new construction and for the strengthening of existing structures. A review of nonlaminated carbon FRP strap system properties and applications in the context of reinforced concrete, timber, and masonry structures is presented.

The effectiveness of fiber-reinforced polymer (FRP) and textile-reinforced mortar (TRM) jackets was investigated experimentally and analytically in this study to confine old-type reinforced concrete (RC) columns with limited capacity because of bond failure at lap-splice regions. The local bond strength between lap-spliced bars and concrete was measured experimentally along the lap-splice region of six full-scale RC columns subjected to cyclic uniaxial flexure under constant axial load. The bond strength of the two column specimens tested without retrofitting was found to be in good agreement with the predictions given by two existing bond models. These models were modified to account for the contribution of composite material jacketing to the bond resistance between lap-spliced bars and concrete. The effectiveness of FRP and TRM jackets against splitting at lap splices was quantified as a function of jacket properties and geometry as well as in terms of the jacket effective strain, which was found to depend on the ratio of lap-splice length to bar diameter. Consequently, simple equations for calculating the bond strength of lap splices in members confined with composite materials (FRP or TRM) are proposed.

This paper presents the test results of reinforced concrete slabs strengthened with prestressed and gradually anchored carbon fiber–reinforced polymer (CFRP) strips under monotonic and cyclic loading. To take full advantage of the externally bonded CFRP technique, it is beneficial to apply the laminates in a prestressed state, which relieves the stress in the steel reinforcement and reduces crack widths and deflection. The aim of the monotonic tests was to determine the strengthening efficiency of the new prestressing technique and to investigate serviceability and ultimate states. The cyclic tests were performed to identify the fatigue behavior of the strengthened slabs and to investigate the influence of long-term cyclic loading and elevated temperature on the bond properties of the prestressed CFRP laminates and the ductility and flexural strength of the strengthened slabs. A nonlinear analytical model of reinforced concrete members strengthened with passive and prestressed CFRP strips under static loading is proposed in the paper. A comparison of the experimental and predicted results reveals an excellent agreement in the full range of loading.

Strengthening two-way slabs by using fiber-reinforced polymer (FRP) is experimentally and analytically evaluated. Results show that the punching capacity of two-way slabs can increase to up to 40% greater than that of a reference specimen. A three-dimensional FEM program called 3D CAMUI, which was developed at Hokkaido University, was used to simulate the experimental slabs. Very good agreement is obtained in load-carrying capacity and modes of failure. An analytical model based on the numerical simulation, which discloses the mechanism of punching shear strength enhancement by FRP strengthening, is proposed to predict the punching shear strength of two-way slabs externally strengthened with FRP sheets.

In civil engineering today, only 20 to 30% of the strength of carbon-fiber-reinforced polymer (CFRP) strips is used when they are applied as externally bonded strips for flexural and shear strengthening or in confinement of reinforced concrete (RC) structural elements. The strips are better used when the CFRP material is prestressed. This offers several advantages, including reduced crack widths, reduced deflections, reduced stress in the internal steel, and possibly increased fatigue resistance. In this paper, recent developments in the field of RC strengthening using prestressed CFRP are presented. The paper focuses on developments in flexural and shear strengthening and column confinement made at the Swiss Federal Laboratory for Materials Testing and Research (Empa). Several innovative ideas have been successfully realized in the laboratory. For example, a gradient prestressing technique without end anchorage plates was developed and successfully applied to a 17 m RC bridge girder. A confinement technique using nonlaminated thermoplastic CFRP straps was also investigated and applied to 2 m high RC columns. These results are encouraging, although practical and theoretical problems remain to be solved before these techniques can be fully applied.

This paper evaluates the effectiveness of different externally bonded glass fiber–reinforced polymer (GFRP) systems for increasing the out-of-plane resistance of infill masonry walls to loading. The research included a comprehensive experimental program comprising 14 full-scale specimens, including four unstrengthened (control) specimens and 10 strengthened specimens. To simulate the boundary conditions of infill walls, all specimens consisted of a reinforced concrete (RC) frame, simulating the supporting RC elements of a building superstructure, which was infilled with solid concrete brick masonry. The specimens were loaded out-of-plane using uniformly distributed pressure to simulate the differential (suction) pressure induced by a tornado. Parameters investigated in the experimental program included aspect ratio, FRP coverage ratio, number of masonry wythes, and type of FRP anchorage. Test results indicated that the type of FRP anchorage had a significant effect on the failure mode. Research findings concluded that GFRP strengthening of infill masonry walls is effective in increasing the out-of-plane load-carrying capacity when proper anchorage of the FRP laminate is provided.

A two-dimensional (2D) nonlinear numerical analysis code by using the rigid body spring method (RBSM) was developed by the writers at Hokkaido University to simulate the behavior of reinforced concrete (RC) members strengthened with fiber-reinforced polymer (FRP) sheets. The code supports the nonlinear constitutive laws for the different materials and nonlinear bond stress-slip relationships for steel-concrete and FRP sheet-concrete interfaces. This study uses the aforementioned code to examine the uniaxial tension behavior of RC members strengthened with carbon fiber sheets (CFS). Experimental results are compared with relevant numerical outputs to validate the model and confirm its ability to simulate the experimental observations. This study also assesses the influence of the amount of CFS strengthening on the tension-stiffening behavior of strengthened members. Finally, this research also suggests new analytical expressions for the average stress-strain relationships of concrete and steel in tension in the presence of stiffening contributions from internal steel reinforcement bars and externally bonded CFS reinforcement.

Results of the behavior of pultruded fiber-reinforced polymer (FRP) I-shaped beams subjected to concentrated loads in the plane of the web are presented. Twenty beams with nominal depths from 152.4 to 304.8 mm were tested in three-point bending with a span-to-depth ratio of four. Load was applied to the top flange directly above the web—12 without bearing plates and 8 with bearing plates of varying width and thickness. All test specimens failed with a wedgelike shear failure at the upper web-flange junction. Finite-element results support experimental findings from strain gauge and digital image correlation data. Bearing plates increased beam capacity by 35% or more as a function of bearing plate width and thickness. Bearing plates increased average shear stress in the web at failure from 17.4 to 27.2 MPa—below the accepted value of in-plane shear strength (69 MPa). A design equation is presented, and predicted capacities are compared with experimental results. The average value of experimental capacity to predicted capacity is 1.12 with a standard deviation of 0.11 and coefficient of variation (COV) of 0.10 for sections up to 304.8 mm deep.

Solar power has merit as a renewable source of energy; it is the largest asset available for consumption on Earth and is limitless. There have been many ideas proposed to beam solar power to Earth; all have been dependent upon the provision of a backing frame to support solar panels, photovoltaic cells, and transmission. This paper suggests one type of rigid deployable skeletal structure and its material of manufacture to form the backing frame of solar panel systems; the structure takes the form of a skeletal double-layer tetrahedral system. The composite material is polyethersulphone thermoplastic polymer reinforced with carbon fiber (CF). This paper also discusses the hostile environment of space in relation to the fiber-reinforced polymer (FRP) composite material, with special reference to the thermal response. Finally, it suggests the alternate possibility of using a rigidized inflatable flexible skeletal structure and, as far as is possible, compares (a) the relative cost of transferring the two structures to low Earth orbit from Earth, and (b) the cost of solar energy relative to other forms of energy.