Journal of Composites for Construction

The capacity and ductility of RC slabs are affected by the use of fiber-reinforced polymer (FRP) as their main reinforcement for repair and rehabilitation. The balance between increasing the capacity and reducing the ductility of flexural members reinforced with FRP was always a matter of discussion. In this research, innovative hybrid reinforcement system (HRS) was introduced to provide the required increase in capacity while keeping the ductility within an acceptable range. Ten RC one-way slabs were tested in this investigation. They included a control slab which was reinforced with ordinary steel, while the rest of the slabs were reinforced internally with HRS with nine different profiles. The main variables considered in this study were the type of core or perimeter reinforcement and the number of perimeter reinforcing layers. It was revealed that the use of the innovative HRS resulted in remarkable increases in section ultimate load capacity as well as ductility.

Several codes and design guidelines addressing fiber-reinforced polymer (FRP) bars as primary reinforcement for structural concrete have been recently published worldwide. This reflects the great progress in FRP research area that has been conducted by the research community over the past two decades. Most of these design provisions follow the traditional approach of $V_c+V_s$ for shear design. Nevertheless, both equations of concrete contribution $V_c$ and FRP stirrup contribution $V_s$ to shear strength in these guidelines are different in the manner that they are calculated. In this paper, five methods for FRP shear design, currently used in design practice, were reviewed. These methods include the American Concrete Institute design guide, ACI 440.1R-06; the Canadian Standards Association, CAN/CSA-S806-02; the ISIS Canada design manual, ISIS-M03-07; the British Institution of Structural Engineers guidelines; and the design recommendations of the Japan Society of Civil Engineers. The five methods for shear design prescribed in these guidelines were compared with experimental database obtained from the literature. In addition, the modified compression field theory approach was reviewed and compared with the experimental database.

An experimental and analytical study is conducted in order to investigate the flexural behavior of masonry beams that are internally reinforced using glass fiber-reinforced polymers (GFRP) rebars. Seven reinforced masonry beams with 4.0- and 2.4-m spans were tested under four-point bending setup. The beams were loaded monotonically up to failure. One had two courses of hollow concrete masonry units and the remaining six beams had three courses. Two masonry beams were reinforced using conventional steel rebars and were considered as the control specimens. The remaining five beams were internally reinforced using GFRP rods with different reinforcement ratios. Beams were detailed to have sufficient shear reinforcement such that they do not fail in shear. Flexural capacity, deformation, curvature, and strains of the tested GFRP-reinforced and steel-reinforced masonry beams were compared and discussed. Using the acquired data from the experimental and analytical studies, effectiveness of GFRP rods as internal reinforcement for concrete masonry beams is demonstrated.

This paper deals with the experimental characterization of the mechanical tensile and shear bond behavior of fiber-reinforced polymer (FRP) sheets externally glued on masonry prisms, in terms of load capacity and stress distribution along the bonded length. The brick masonry adopted tries to replicate ancient brick masonry, by using handmade low-strength solids bricks and low-strength lime-based mortar. Key parameters relative to the FRP-masonry interface response, particularly bonded length, FRP materials, anchor scheme adopted, and shape of masonry substrate, were studied. Finally, an analytical bond stress-slip formulation was developed, allowing deducing local bond stress-slip curves directly from the experiments.

This study investigated the flexural behavior of corroded steel reinforced concrete beams repaired with carbon-fiber-reinforced polymer (CFRP) sheets under repeated loading. Thirty beams $\left(152\times 254\times 2,000\text{mm}\right)$ were constructed and tested. Fatigue flexural failure occurred in 29 of these beams. The study showed that pitting of the steel reinforcement due to corrosion occurred only after about a 7% actual mass loss which coincided with a decrease in the fatigue performance of the beam. The controlling factor for the fatigue strength of the beams is the fatigue strength of the steel bars. Repairing with CFRP sheets increased the fatigue capacity of the beams with corroded steel reinforcement beyond that of the control unrepaired beams with uncorroded steel reinforcement. Beams repaired with CFRP at a medium corrosion level and then further corroded to a high corrosion level before testing had a comparable fatigue performance to those that were repaired and tested after corroding directly to a high corrosion level.

This paper presents the development of a test method that can be used to test the bond capacity of carbon fiber-reinforced polymer (CFRP) composites bonded to concrete. The rationale for the selection of the test method is described along with the results of the experimental work used to refine the test configuration and procedures. The research objectives were to develop a test method that (1) can be used to evaluate the durability of the FRP-concrete bond (adhesion failure mode); (2) facilitate multiple replicate for statistical validation; (3) is simple to conduct; and (4) provides comparative results that are easy to interpret. The method utilizes a small concrete beam modeled after the modulus of rupture test, which is typically used to measure concrete tensile strength. A number of small beam sizes and loading configurations were considered during the investigation. The final recommended specimen configuration is $4\times 4\times 14\text{in}\text{.}$ $\left(100\text{mm}\times 100\text{mm}\times 356\text{mm}\right)$ beam with a half-depth saw cut at midspan. A 1 in. (25 mm) wide by 8 in. (203 mm) long CFRP strip is applied to the tension face of the beam over the saw cut. The specimen is loaded until failure with a single concentrated load at midspan over a 12 in. (305 mm) span. For durability testing, samples are prepared with the same materials and exposed to the desired accelerated conditioning protocol. Companion unexposed samples are also tested and the relative decrease in capacity is reported as the load to failure of the exposed specimen to that of the control specimen.

This paper deals with the shear strengthening of RC beams using externally bonded (EB) fiber-reinforced polymers (FRP). Current code provisions and design guidelines related to shear strengthening of RC beams with FRP are discussed in this paper. The findings of research studies, including recent work, have been collected and analyzed. The parameters that have the greatest influence on the shear behavior of RC members strengthened with EB FRP and the role of these parameters in current design codes are reviewed. This study reveals that the effect of transverse steel on the shear contribution of FRP is important and yet is not considered by any existing codes or guidelines. Therefore, a new design method is proposed to consider the effect of transverse steel in addition to other influencing factors on the shear contribution of FRP $\left(V_f\right)$ . Separate design equations are proposed for U-wrap and side-bonded FRP configurations. The accuracy of the proposed equations has been verified by predicting the shear strength of experimentally tested RC beams using data collected from the literature. Finally, comparison with current design guidelines has shown that the proposed model achieves a better correlation with experimental results than current design guidelines.

A retrofitting technique that uses prestressed unbonded carbon-fiber-reinforced polymer (CFRP) straps to provide additional shear capacity has previously been shown to be successful under short-term static loading conditions. The current study explores the longer-term behavior of this retrofitting technique through two experiments (a sustained load and a cyclic load experiment) and the development of a model based on the modified compression field theory. The experiments indicated that the strain in the CFRP straps changes with time due to changes in the load sharing with the concrete (caused by creep) and the steel stirrups (caused by yield of these elements). The predictive model was initially validated against static experimental results before being applied to the longer-term experiments. The model predicts the trends in behavior well although it is conservative in its estimates of strap strain. The model was then used to determine the influence of stirrup yielding, the load level before and after retrofitting, and the duration of loading on the CFRP strap strains. The initial results suggest that the largest increases in long-term strap strain will occur when the straps are installed early in the structure’s service life although further experimental validation is required.

Bond tests were conducted on concrete beams strengthened with near-surface-mounted (NSM) nonprestressed and prestressed carbon fiber-reinforced polymer (CFRP) rods under static loading. In the NSM technique, the CFRP rods are placed inside precut grooves and bonded to the concrete with epoxy adhesive. Six concrete beams were tested. The test variables included presence of internal tension steel reinforcement (unreinforced and reinforced), use of NSM CFRP strengthening (nonprestressed and prestressed), and type of CFRP rod (spirally wound and sand blasted). The beams were tested statically in four-point bending. Based on the test results, the transfer length for the prestressed CFRP rod in epoxied groove was 150 and 210 mm for the sand blasted and spirally wound rods, respectively. The main failure mode was debonding between the CFRP rod and the epoxy that starts at sections close to the midspan then, as the load increases, it propagates toward the supports. At failure, the beams strengthened with a given rod type showed the same CFRP strain at sections close to the support (29% of ultimate strain for spirally wound bars and 39% of ultimate strain for sand blasted bars). A cracked section analysis was carried out and compared well with the measured results.

The flexural behavior of RC T-beams strengthened with prestressed near-surface-mounted (NSM) carbon fiber-reinforced-polymer (CFRP) reinforcement was investigated. The specific objective was to study the effect of partial unbonding of the CFRP reinforcement on the beam flexural behavior to increase the deformability. A total of eight RC T-beams were tested under four-point monotonic loading. The main variables were the level of prestressing force in the CFRP bars and the unbonded length at the midspan of the beam. The test results showed that all of the prestressed strengthened beams effectively improved the ultimate load-carrying capacity and the serviceability performance compared to the unstrengthened beam. The partially bonded prestressed beams exhibited an enhancement of the deformability compared to the fully bonded beams while minimizing the reduction of the load-carrying capacity. Partial unbonding was more effective to improve the deformability at higher levels of prestressing force. The general behavior of the partially bonded beams was reasonably well predicted by an analytical model developed previously by the writers.

Near-surface-mounted (NSM) reinforcement has become a well-known method for strengthening existing concrete structures. The bond between the NSM reinforcing bars and concrete is the key factor in the NSM technique. In the NSM technique, there are two bond interfaces: one between the NSM bar and the adhesive, and the other between the adhesive and the concrete. For this technique to perform efficiently, these two interfaces need to be investigated. On the other hand, concrete structures that require rehabilitation are often exposed to aggressive environments. Many of these environments are related to cold-climate conditions as can be found in Canada. Environmental factors including freeze/thaw action, exposure to deicing salts, and sustained low temperatures combine to attack the integrity of repaired structures. Consequently, repair materials for the Canadian infrastructure must be able to withstand these harsh conditions for prolonged periods of time. A total of 80 NSM-fiber-reinforced polymer (FRP) bars installed in C-shaped concrete specimens were tested in pull-out setup to failure. Sixty specimens were tested at normal room temperature, while the remaining 20 specimens were tested after conditioning in an environmentally controlled chamber for 200 freeze/thaw cycles. The dimensions of the specimens were designed, upon a preliminary phase of testing, to ensure that no transverse cracking would occur in the specimen before bond failure of the NSM bar. The results are presented in term of failure load, average bond stress, strains in FRP bar, end slip, and mode of failure. A bond-slip model was proposed for the used FRP bars.

The external confinement of RC columns by means of externally bonded fiber-reinforced polymer (FRP) laminates is a well established technique for strengthening and retrofitting purposes. This paper presents a pilot research that includes laboratory testing of full-scale square and rectangular RC columns externally confined with glass and basalt-glass FRP laminates and subjected to pure axial load. Specimens that are representative of full-scale building columns were designed according to a dated American Concrete Institute (ACI) 318 code (i.e., prior to 1970) for gravity loads only. The study was conducted to investigate how the external confinement affects peak axial strength and deformation of a prismatic RC column. The results showed that the FRP confinement increases concrete axial strength, but it is more effective in enhancing concrete strain capacity. The discussion of the results includes a comparison with the values obtained using existing constitutive models.