Experimental Investigation of Dynamic Behavior of RC Frame Strengthened with Buckling-Restrained Bracing
Publication: Journal of Structural Engineering
Volume 148, Issue 7
Abstract
This paper presents the results of an investigation of the dynamic behavior of a reinforced concrete frame that was strengthened by a buckling-restrained brace (BRB). The behavior of this frame was benchmarked against a control frame without strengthening. Both frames were tested concurrently on a shake table using the acceleration time-history record from the 1995 Kobe earthquake. The BRB-strengthened frame was additionally subjected to two levels of a synthetic time-history record to observe its behavior under severe ground shaking. The stiffness of the BRB-strengthened frame increased by 70% relative to the control frame. Furthermore, the cracked BRB-strengthened frame retained approximately 80% higher stiffness compared with the cracked control frame at an applied peak ground acceleration (PGA) of . Conversely, the lateral story drift of the BRB-strengthened frame was 46% less compared with the control frame at this level of acceleration. The control frame failed by concrete crushing at base of the columns at PGA of after yielding of the longitudinal reinforcing bars. The dissipation of hysteretic energy for the control frame reached a maximum at , whereas the BRB-strengthened frame exhibited high strength capacity without any marked change in stiffness at .
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The authors wish to acknowledge the support provided for this research by the laboratory technical staff members. The assistance from Steel Canada in arranging the testing of frames is gratefully acknowledged.
References
ACI (American Concrete Institute). 2005. Acceptance criteria for moment frames based on structural testing and commentary. ACI 374.1-05. Farmington Hills, MI: ACI.
Almeida, A., R. Ferreira, J. M. Proença, and A. S. Gago. 2017. “Seismic retrofit of RC building structures with buckling restrained braces.” Eng. Struct. 130 (Jan): 14–22. https://doi.org/10.1016/j.engstruct.2016.09.036.
Al-Sadoon, Z. 2016. “Seismic retrofitting of conventional reinforced concrete moment-resisting frames using buckling restrained braces.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Ottawa.
Al-Sadoon, Z. A., M. Saatcioglu, and D. Palermo. 2020. “New buckling-restrained brace for seismically deficient reinforced concrete frames.” J. Struct. Eng. 146 (6): 04020082. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002439.
ASTM. 2005. Standard specification for deformed and plain carbon-steel bars for concrete reinforcement. ASTM A615/A615M-05. West Conshohocken, PA: ASTM.
Bairrao, R., and M. F. Silva. 2009. “Shaking table tests of two different reinforcement techniques using polymeric grids on an asymmetric limestone full-scaled structure.” Eng. Struct. 31 (6): 1321–1330. https://doi.org/10.1016/j.engstruct.2008.04.039.
Bairrao, R., and C. Vaz. 2000. “Shaking table testing of civil engineering structures—The LNEC 3D simulator experience.” In Proc., 12th World Conf. on Earthquake Engineering. Wellington, New Zealand: New Zealand Society for Earthquake Engineering.
Bertero, V. V., and C.-M. Uang. 1992. “Issues and future directions in the use of an energy approach for seismic resistant design of structures.” In Nonlinear seismic analysis and design of reinforced concrete buildings, edited by P. Fajfar and H. Krawinkler, 3–22. London: Elsevier.
Broderick, B. M., A. S. Elnashai, N. N. Ambraseys, J. M. Barr, R. G. Goodfellow, and E. M. Higazy. 1994. The Northridge (California) earthquake of 17 January 1994: Observations, strong motion and correlative response analyses. London: Engineering Seismology and Earthquake Engineering, Imperial College.
Carvalho, E. C. 1998. “Seismic testing of structures.” In Proc., 11th European Conf. on Earthquake Engineering, 53–64. Boca Raton, FL: CRC Press.
Chandra, J., and P. Warnitchai. 2011. “Application of buckling restrained braces for seismic strengthening of irregular gravity load designed reinforced concrete frame buildings.” Civ. Eng. Dimension 13 (2): 65–74. https://doi.org/10.9744/ced.13.2.65-74.
Chao, S.-H., and S. C. Goel. 2006. “Performance-based seismic design of eccentrically braced frames using target drift and yield mechanism as performance criteria.” Eng. J. Am. Inst. Steel Constr. 43 (3): 173–200.
Chao, S.-H., and S. C. Goel. 2008. “Performance-based plastic design of special truss moment frames.” Eng. J. Am. Inst. Steel Constr. 45 (2): 127–150.
Chen, R., C. Qiu, and D. Hao. 2020. “Seismic response analysis of multi-story steel frames using BRB and SCB hybrid bracing system.” Appl. Sci. 10 (1): 284. https://doi.org/10.3390/app10010284.
Choi, H., J. Erochko, C. Christopoulos, and R. Tremblay. 2008. “Comparison of the seismic response of steel buildings incorporating self-centering energy dissipative braces, buckling restrained braced and moment resisting frames.” In Proc., 14th World Conf. on Earthquake Engineering. Beijing: Chinese Association of Earthquake Engineering.
Choi, H., and J. Kim. 2006. “Energy-based seismic design of buckling-restrained braced frames using hysteretic energy spectrum.” Eng. Struct. 28 (2): 304–311. https://doi.org/10.1016/j.engstruct.2005.08.008.
D’Aniello, M., G. D. Corte, and F. M. Mazzolani. 2006. “Seismic upgrading of RC buildings by buckling restrained braces: Experimental results vs numerical modeling.” In Proc., 5th Int. Conf. on Behaviour of Steel Structures in Seismic Areas (STESSA 2006), edited by Federico Mazzolani and Akira Wada, 26–28. Boca Raton, FL: CRC Press.
Dinu, F., S. Bordea, and D. Dubina. 2012. “Strengthening of non-seismic reinforced concrete frames of buckling restrained steel braces.” In Behaviour of steel structures in seismic areas, 1085–1090. Boca Raton, FL: CRC Press.
Di Sarno, L., and G. Manfredi. 2010. “Seismic retrofitting with buckling restrained braces: Application to an existing non-ductile RC framed building.” Soil Dyn. Earthquake Eng. 30 (11): 1279–1297. https://doi.org/10.1016/j.soildyn.2010.06.001.
Di Sarno, L., and G. Manfredi. 2012. “Experimental tests on full-scale RC unretrofitted frame and retrofitted with buckling-restrained braces.” Earthquake Eng. Struct. Dyn. 41 (2): 315–333. https://doi.org/10.1002/eqe.1131.
EERI (Earthquake Engineering Research Institute). 2009. “The 6.3 Abruzzo, Italy, Earthquake of April 6, 2009.” Accessed January 3, 2021. http://www.reluis.it/doc/pdf/Aquila/EERI_L_Aquila_report.pdf.
Erochko, J., C. Christopoulos, R. Tremblay, and H. Choi. 2011. “Residual drift response of SMRFs and BRB frames in steel buildings designed according to ASCE 7-05.” J. Struct. Eng. 137 (5): 589–599. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000296.
Ferraioli, M., and A. Lavino. 2018. “A displacement-based design method for seismic retrofit of RC buildings using dissipative braces.” Math. Probl. Eng. 2018: 1–28. https://doi.org/10.1155/2018/5364564.
Henderson, R. C., K. E. Fricke, W. D. Jones, J. E. Beavers, and R. M. Bennett. 2003. “Summary of a large- and small-scale unreinforced masonry infill test program.” J. Struct. Eng. 129 (12): 1667–1675. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:12(1667).
ICBO (International Council of Building Officials). 1997. Uniform building code (UBC 9). Whitter, CA: ICBO.
Kasai, K., Y. Fu, and A. Watanabe. 1998. “Passive control systems for seismic damage mitigation.” J. Struct. Eng. 124 (5): 5501–5512. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:5(501).
Kiggins, S., and C.-M. Uang. 2006. “Reducing residual drift of buckling-restrained braced frames as a dual system.” Eng. Struct. 28 (11): 1525–1532. https://doi.org/10.1016/j.engstruct.2005.10.023.
Krstevska, L., L. Tashkov, K. Gramatikov, R. Landolfo, O. Mammana, F. Portioli, and F. Mazzolani. 2010. “Large-scale experimental investigation on Mustafa Pasha Mosque.” J. Earthquake Eng. 14 (6): 842–873. https://doi.org/10.1080/13632460903338528.
Lee, H. S., K. B. Lee, K. R. Hwang, and C. S. Cho. 2013. “Shake table responses of an RC low-rise building model strengthened with buckling restrained braces at ground story.” Earthquake Struct. 5 (6): 703–731.
Lee, S.-S., and S. C. Goel. 2001. Performance-based design of steel moment frames using target drift and yield mechanism. Ann Arbor, MI: Univ. of Michigan.
López, W. A., and R. Sabelli. 2004. Seismic design of buckling-restrained braced frames. Chicago: Structural Steel Education Council.
Mahrenholtz, C., P.-C. Lin, A.-C. Wu, K.-C. Tsai, S.-J. Hwang, R.-Y. Lin, and M. Bhayusukma. 2015. “Retrofit of reinforced concrete frames with buckling-restrained braces.” Earthquake Eng. Struct. Dyn. 44 (1): 59–78. https://doi.org/10.1002/eqe.2458.
Marshall, J. D. 2021. “Buckling-restrained braces and their implementation in structural design of steel buildings.” In Encyclopedia of earthquake engineering, edited by M. Beer, I. Kougioumtzoglou, E. Patelli, and I. K. Au. Berlin: Springer.
Mazzolani, F. M. 2006. Seismic upgrading of RC buildings by advanced techniques: The ILVA-IDEM research project. Monza, Italy: Polimetrica.
Melek, M., and J. W. Wallace. 2004. “Performance of columns with short lap splices.” In Proc., 13th World Conf. on Earthquake Engineering. Vancouver, BC, Canada: Canadian Association for Earthquake Engineering.
Mendes, N., and P. B. Lourenco. 2010. “Seismic assessment of masonry ‘Gaioleiro’ buildings in Lisbon, Portugal.” J. Earthquake Eng. 14 (1): 80–101. https://doi.org/10.1080/13632460902977474.
Naeim, F., M. Lew, S. C. Huang, H. K. Lam, and L. D. Carpenter. 2000. “The performance of tall buildings during the 21 September 1999 Chi-Chi earthquake, Taiwan.” Struct. Des. Tall Build. 9 (2): 137–160. https://doi.org/10.1002/(SICI)1099-1794(200005)9:2%3C137::AID-TAL149%3E3.0.CO;2-D.
Pei, S., and J. W. van de Lindt. 2011. “Seismic numerical modeling of a six-story light-frame wood building: Comparison with experiments.” J. Earthquake Eng. 15 (6): 924–941. https://doi.org/10.1080/13632469.2010.544840.
Rafi, M. M., S. H. Lodi, Z. A. Al-Sadoon, M. Saatcioglu, and D. Palermo. 2021a. “Shake-table testing of deficient reinforced concrete frame retrofitted with buckling restrained brace.” ACI Struct. J. 118 (3): 161–173. https://doi.org/10.14359/51729351.
Rafi, M. M., S. H. Lodi, and S. A. Qazi. 2021b. “Dynamic testing of seismic resistant cob structure for post-earthquake reconstruction.” J. Earthquake Eng. 25 (6): 1009–1030. https://doi.org/10.1080/13632469.2018.1531092.
Sabelli, R., S. Mahin, and C. Chang. 2003. “Seismic demands on steel braced frame buildings with buckling-restrained braces.” Eng. Struct. 25 (5): 655–666. https://doi.org/10.1016/S0141-0296(02)00175-X.
Soong, T. T., and B. F. Spencer Jr. 2002. “Supplemental energy dissipation: State-of-the-art and state-of-the-practice.” Eng. Struct. 24 (3): 243–259. https://doi.org/10.1016/S0141-0296(01)00092-X.
Tomaževič, M., and M. Gams. 2012. “Shaking table study and modelling of seismic behaviour of confined AAC masonry buildings.” Bull. Earthquake Eng. 10 (3): 863–893. https://doi.org/10.1007/s10518-011-9331-x.
Tsai, K.-C., A.-C. Wu, K.-Y. Pan, and H.-H. Yang. 2017. “Buckling restrained braces for existing and new reinforced concrete frames.” In Proc., 2017 World Congress on Advances in Structural Engineering and Mechanics (ASEM17). Daejeon, Korea: Techno-Press Journals.
Uriz, P., F. C. Filippou, and S. A. Mahin. 2008. “Model for cyclic inelastic buckling of steel braces.” J. Struct. Eng. 134 (4): 619–628. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:4(619).
Vaseghi Amiri, J., M. Naeej, and M. Reza Naeej. 2013. “Seismic retrofitting of steel frames with buckling restrained braces.” Iran. J. Energy Environ. 4 (3): 178–185. https://doi.org/10.5829/idosi.ijee.2013.04.03.02.
Wang, Y., L. Ibarra, and C. Pantelides. 2019. “Collapse capacity of reinforced concrete skewed bridges retrofitted with buckling-restrained braces.” Eng. Struct. 184 (Apr): 99–114. https://doi.org/10.1016/j.engstruct.2019.01.033.
Watanabe, E., K. Sugiura, K. Nagata, and Y. Kitane. 1998. “Performances and damages to steel structures during the 1995 Hyogoken-Nanbu earthquake.” Eng. Struct. 20 (4–6): 282–290. https://doi.org/10.1016/S0141-0296(97)00029-1.
Wu, A.-C., K.-C. Tsai, H.-H. Yang, J.-L. Huang, C.-H. Li, K.-J. Wang, and H.-H. Khoo. 2017. “Hybrid experimental performance of a full-scale two-story buckling-restrained braced RC frame.” Earthquake Eng. Struct. Dyn. 46 (8): 1223–1244. https://doi.org/10.1002/eqe.2853.
Wu, K., Z. Tao, H. Gong, D. Hu, Y. Bai, W. Pan, W. Yu, and G. Wei. 2015. “Shaking table test on RC frame structure with buckling restrained braces.” J. Build. Struct. 36 (9): 18–28.
Xie, Q. 2005. “State of the art of buckling-restrained braces in Asia.” J. Constr. Steel Res. 61 (6): 727–748. https://doi.org/10.1016/j.jcsr.2004.11.005.
Yooprasertchai, E., and P. Warnitchai. 2008. “Seismic retrofitting of low-rise non-ductile reinforced concrete buildings by buckling-restrained braces.” In Proc., 14th World Conf. on Earthquake Engineering. Beijing: Chinese Association of Earthquake Engineering.
Youssef, N. F. G., D. Bonowitz, and J. L. Gross. 1995. A survey of steel moment-resisting frame buildings affected by the 1994 Northridge earthquake. Gaithersburg, MD: NIST.
Zhou, X., and G. Li. 2010. “Shaking table model test of a steel-concrete composite high-rise building.” J. Earthquake Eng. 14 (4): 601–625. https://doi.org/10.1080/13632460903193949.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Feb 11, 2021
Accepted: Feb 15, 2022
Published online: Apr 27, 2022
Published in print: Jul 1, 2022
Discussion open until: Sep 27, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Yao Chen, Jiayao Shi, Chenhao Lu, Jian Feng, Pooya Sareh, Hierarchical Clustering-Based Collapse Mode Identification and Design Optimization of Energy-Dissipation Braces Inspired by the Triangular Resch Pattern, Journal of Structural Engineering, 10.1061/JSENDH.STENG-12805, 150, 5, (2024).
- Huailei Qin, Kaiming Bi, Huihui Dong, Qiang Han, Xiuli Du, Shake Table Tests on RC Double-Column Bridge Piers with Self-Centering Energy Dissipation Braces, Journal of Bridge Engineering, 10.1061/JBENF2.BEENG-6069, 28, 8, (2023).