Fatigue Performance of Bird-Beak SHS Gap K-Joints under Brace In-Plane Force
Publication: Journal of Structural Engineering
Volume 147, Issue 11
Abstract
This paper presents a test campaign concerning the fatigue behavior of the bird-beak square hollow section (SHS) gap K-joints subjected to brace in-plane force. A total of four bird-beak SHS gap K-joint specimens were tested. Prior to the high-cycle fatigue tests, static in-plane force was applied to the braces of K-joint to determine the hot-line strain distributions and the stress concentration factors (SCFs) via extrapolation. Based on the results of static loading tests, the amplitude of cyclic load can be further determined. Subsequently, high-cycle fatigue tests were performed on the square and diamond bird-beak SHS gap K-joints to investigate the fatigue behavior from different perspectives, such as failure mode, fatigue life, crack propagation, and stiffness degradation. The test results demonstrate that the brace crown region always possessed the most severe stress concentration, which coincided with the location of crack initiation. This implies that the experimentally obtained SCFs can accurately predict the crack initiation location. The test fatigue lives of bird-beak gap K-joints were compared with the predictions by the International Institute of Welding (IIW) design curves originally developed for the conventional joints.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The research work was supported by National Natural Science Foundation of China (No. 51678359) and National Key Research and Development Program of China (Nos. 2016YFB1200602-28 and 2016YFB1200601-B27). The supports are gratefully acknowledged.
References
Cheng, B., F. H. Huang, C. Li, Y. H. Duan, and X. L. Zhao. 2020. “Hot spot stress and fatigue behavior of bird-beak SHS X-joints subjected to brace in-plane bending.” Thin Walled Struct. 150 (May): 106701. https://doi.org/10.1016/j.tws.2020.106701.
Cheng, B., C. Li, Y. Lou, and X. L. Zhao. 2018. “Parametric FE modeling to predict hot spot stress concentrations of bird-beak SHS joints in offshore structures.” Ocean Eng. 160 (15): 54–67. https://doi.org/10.1016/j.oceaneng.2018.04.077.
Cheng, B., Q. Qian, and X. L. Zhao. 2014. “Tests to determine stress concentration factors for square bird-beak SHS joints under chord and brace axial forces.” J. Struct. Eng. 140 (11): 04014088. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001095.
Cheng, B., Q. Qian, and X. L. Zhao. 2015a. “Numerical investigation on stress concentration factors of square bird-beak SHS T-joints subject to axial forces.” Thin Walled Struct. 94 (9): 435–445. https://doi.org/10.1016/j.tws.2015.05.003.
Cheng, B., Q. Qian, and X. L. Zhao. 2015b. “Stress concentration factors and fatigue behavior of square bird-beak SHS T-joints under out-of-plane bending.” Eng. Struct. 99 (9): 677–684. https://doi.org/10.1016/j.engstruct.2015.05.033.
Christitsas, A. D., D. T. Pachoumis, C. N. Kalfas, and E. G. Galoussis. 2007. “FEM analysis of conventional and square bird-beak SHS joint subjected to in-plane bending moment-experimental study.” J. Constr. Steel Res. 63 (10): 1361–1372. https://doi.org/10.1016/j.jcsr.2006.12.006.
Davies, G., J. S. Owen, R. Kelly, J. S. Chung, B. M. Das, and J. Roesset, eds. 1996. “Bird beak T-joints in square hollow sections: A finite element investigation.” In Proc., 6th Int. Offshore and Polar Engineering Conf., 1–6. Mountain View, CA: International Society of Offshore and Polar Engineers.
Huang, F. H., B. Cheng, C. Li, and X. L. Zhao. 2020. “Fatigue behavior of bird-beak SHS X-joints under cyclic brace axial forces.” J. Constr. Steel Res. 169 (Jun): 106021. https://doi.org/10.1016/j.jcsr.2020.106021.
Ishida, K. 1992. “Experimental research on fatigue behavior of diamond bird-beak joint.” [In Japanese.] In Proc., Symp. on Structural Engineering. Tokyo: Architectural Institute of Japan.
Ishida, K., T. Ono, M. Iwata, M. G. Coutie, and G. Davies, eds. 1993. “Ultimate strength formula for joints of new truss system using rectangular hollow sections.” In Proc., Int. Symp. on Tubular Structures, 511–518. London: E&FN Spon.
Lei, L. 2009. “The analysis of square bird-beak SHS joint subject to in-plane bending moment.” M.S. thesis, Dept. of Civil Engineering, Xi’an Univ. of Architecture and Technology.
Li, C., F. H. Huang, Y. Lou, and B. Cheng. 2018. “Stress concentration factors of bird-beak SHS X-joints under brace axial forces.” J. Constr. Steel Res. 150 (Nov): 87–98. https://doi.org/10.1016/j.jcsr.2018.08.016.
National Standards for the People’s Republic of China. 2002. Cold formed steel hollow sections for general structure-dimensions, shapes, weight and permissible deviation. GB/T 6728–2002. Beijing: National Standards for the People’s Republic of China.
Ono, T., M. Iwata, K. Ishida, M. G. Coutie, and G. Davies, eds. 1993. “Local failure of joints of new truss system using rectangular hollow sections subjected to in-plane bending moment.” In Proc., Int. Symp. on Tubular Structures, 503–510. London: E&FN Spon.
Ono, T., M. Iwata, K. Ishida, P. Grundy, A. Holgate, and B. Wong, eds. 1994. “Local failure of joints of new truss system using rectangular hollow sections subjected to out-of-plane bending moment.” In Proc., Int. Symp. on Tubular Structures, 441–448. London: E&FN Spon.
Ono, T., M. Iwata, K. Ishida, J. Wardenier, and E. Panjeh Shahi, eds. 1991. “An experimental study on joints of new truss system using rectangular hollow sections.” In Proc., Int. Symp. on Tubular Structures, 344–353. London: E&FN Spon.
Owen, J. S., G. Davies, and R. B. Kelly. 1996. “A comparison of the behaviour of RHS bird beak T-joints with normal RHS and CHS systems.” In Proc., Int. Symp. on Tubular Structures, 173–180. London: E&FN Spon.
Owen, J. S., G. Davies, and R. B. Kelly. 2001. “The influence of member orientation on the resistance of cross joints in square RHS construction.” J. Constr. Steel Res. 57 (3): 253–278. https://doi.org/10.1016/S0143-974X(00)00019-5.
Owen, J. S., and R. B. Kelly. 2001. “The effect of purlin loads on the capacity of overlapped birdbeak K joints.” In Proc., Int. Symp. and Euroconf., 229–238. Boca Raton, FL: CRC Press.
Qian, X., C. T. Nguyen, Y. Petchdemaneengam, Z. Qu, S. Swaddiwudhipong, and P. Marshall. 2013a. “Fatigue performance of tubular X-joints with PJP+ welds. Part II: Numerical investigation.” J. Constr. Steel Res. 89 (10): 252–261. https://doi.org/10.1016/j.jcsr.2013.07.003.
Qian, X., Y. Petchdemaneengam, S. Swaddiwudhipong, P. Marshall, Z. Ou, and C. T. Nguyen. 2013b. “Fatigue performance of tubular X-joints with PJP+ welds. Part I: Experimental study.” J. Constr. Steel Res. 90 (11): 49–59. https://doi.org/10.1016/j.jcsr.2013.07.016.
Schumacher, A., and A. Nussbaumer. 2006. “Experimental study on the fatigue behaviour of welded tubular K-joints for bridges.” Eng. Struct. 28 (5): 745–755. https://doi.org/10.1016/j.engstruct.2005.10.003.
Strømmen, E. N., and P. K. Larsen. 1994. “Fatigue tests on a welded RHS lattice girder joint.” J. Constr. Steel Res. 31 (1): 103–114. https://doi.org/10.1016/0143-974X(94)90026-4.
Thévenet, D., M. F. Ghanameh, and A. Zeghloul. 2013. “Fatigue strength assessment of tubular welded joints by an alternative structural stress approach.” Int. J. Fatigue 51 (6): 74–82. https://doi.org/10.1016/j.ijfatigue.2013.02.003.
Tong, L. W., Y. Fu, Y. Liu, and X. L. Zhao. 2014. “Stress concentration factors of diamond bird-beak SHS T-joints under brace loading.” Thin Walled Struct. 74: 201–212. https://doi.org/10.1016/j.tws.2013.10.008.
Tong, L. W., G. W. Xu, D. Q. Yan, and X. L. Zhao. 2016. “Fatigue tests and design of diamond bird-beak SHS T-joints under axial loading in brace.” J. Constr. Steel Res. 118 (3): 49–59. https://doi.org/10.1016/j.jcsr.2015.10.025.
van Wingerde, A. M. 1992. “The fatigue behaviour of T- and X-joint made of square hollow sections.” HERON 37 (2): 1–180.
van Wingerde, A. M., J. A. Packer, J. Wardenier, and D. Dutta. 1996. The fatigue behaviour of K-joints made of square hollow sections. Toronto: Univ. of Toronto.
van Wingerde, A. M., J. A. Packer, and J. Wardenierb. 1995. “Criteria for the fatigue assessment of hollow structural section connections.” J. Constr. Steel Res. 35 (1): 71–115. https://doi.org/10.1016/0143-974X(94)00030-I.
Yang, Y. H., and Z. Yang. 2013. “Analysis of the ultimate strength of diamond bird-beak K-joints.” [In Chinese.] Spatial Struct. 19 (3): 49–54.
Zhao, X. L., S. Herion, J. A. Packer, R. S. Puthli, G. Sedlacek, J. Wardenier, K. Weynand, A. M. van Wingerde, and N. F. Yeomans. 2000. Design guide for circular and rectangular hollow section joints under fatigue loading. Köln, Germany: Comité International pour le Développement et l’Etude de la Construction Tubulaire, TÜV-Verlag.
Zhao, X. L., and J. A. Packer. 2008. Recommended fatigue design procedure for welded hollow section joints. Part 1: Recommendations. Part 2: Commentary. Cambridge, UK: Abington Publishing.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Sep 11, 2020
Accepted: Jun 2, 2021
Published online: Aug 17, 2021
Published in print: Nov 1, 2021
Discussion open until: Jan 17, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- He Zhang, Linjie Yao, Xianglong Zheng, Jiangyi Zhou, A Whole-Rate-Region Fatigue Crack Growth Model Incorporating Nonlinear Rate Evolution Characteristics Based on a Peridynamic Approach, Journal of Engineering Mechanics, 10.1061/JENMDT.EMENG-7962, 150, 12, (2024).
- Fengjun Lv, Wanzhen Wang, Wei Zhao, Fatigue Test and Unified Fatigue Life Calculation of Q460C Steel Notched Plates, Buildings, 10.3390/buildings13030697, 13, 3, (697), (2023).
- Man-Tai Chen, Wenkang Zuo, Ben Young, Tests of Cold-Formed Steel T-Joints with Semi-Oval Hollow Section Chord, Journal of Structural Engineering, 10.1061/JSENDH.STENG-12277, 149, 8, (2023).
- Shusheng Yi, Man-Tai Chen, Ben Young, Stub Column Behavior of Concrete-Filled Cold-Formed Steel Semi-Oval Sections, Journal of Structural Engineering, 10.1061/JSENDH.STENG-11667, 149, 3, (2023).
- M.H. Lai, Y.H. Lin, Y.Y. Jin, Q. Fei, Z.C. Wang, J.C.M. Ho, Uni-axial behaviour of steel slag concrete-filled-steel-tube columns with external confinement, Thin-Walled Structures, 10.1016/j.tws.2023.110562, 185, (110562), (2023).
- Man-Tai Chen, Ao Cai, Madhup Pandey, Chen Shen, Yuelong Zhang, Lili Hu, Mechanical properties of high strength steels and weld metals at arctic low temperatures, Thin-Walled Structures, 10.1016/j.tws.2023.110543, 185, (110543), (2023).
- F.M. Ren, S.Y. Tian, L. Gong, J.L. Wu, J.X. Mo, C.L. Lai, M.H. Lai, Seismic performance of a ring beam joint connecting FTCES column and RC / ESRC beam with NSC, Journal of Building Engineering, 10.1016/j.jobe.2022.105366, 63, (105366), (2023).
- Man-Tai Chen, Yangyu Chen, Ben Young, Experimental investigation on cold-formed steel elliptical hollow section T-joints, Engineering Structures, 10.1016/j.engstruct.2023.115593, 283, (115593), (2023).
- Shusheng Yi, Man-Tai Chen, Ben Young, Design of concrete-filled cold-formed steel elliptical stub columns, Engineering Structures, 10.1016/j.engstruct.2022.115269, 276, (115269), (2023).
- Wenkang Zuo, Hongfei Chang, Zhaowei Li, Aichen An, Junwu Xia, Tao Yu, Experimental investigation on compressive behavior of corroded thin-walled CHS T-joints with grout-filled GFRP tube repairing, Thin-Walled Structures, 10.1016/j.tws.2022.109222, 175, (109222), (2022).