Uncertainly Analysis of Flexural Overstrength for Capacity Design of RC Beams
Publication: Journal of Structural Engineering
Volume 140, Issue 7
Abstract
To ensure an overall ductile structural behavior, the reinforcing steel used in the seismic design of reinforced concrete (RC) structures is governed by certain specific requirements given in many international codes, such as the Eurocodes and the recently released Italian Building Code (IBC). This study’s primary focus is the statistical analysis of reinforcing steel properties, based on data from over 600 material tests. The data sets considered include a wide range of reinforcing steel bars (from 12 to 26 mm) provided by different Italian industries and used for a large structure built in Naples (Southern Italy). The test results are analyzed to determine the appropriate cumulative distribution function for yield and ultimate strengths, as well as the ultimate deformation, and other statistical parameters of interest as defined in the codes. The comparison with previous tests confirms an improvement in the quality of materials, as reflected in reduced variability and increased bias factors, consistent with other investigators’ recent findings. Finally, this study investigates the flexural overstrength of RC beams designed according to the current IBC—consistent with Eurocodes—and the accuracy of code requirements in light of realistic material models both for concrete and reinforcing steel and of uncertainties associated with mechanical models, structural members geometry, and material properties (as obtained in this study for reinforcing steel). The obtained results show that code provisions do not seem conservative and provide a basis for an improved calibration of future editions of seismic design codes for buildings.
Get full access to this article
View all available purchase options and get full access to this article.
References
Anderson, T. W., and Darling, D. A. (1954). “A test of goodness-of-fit.” J. Am. Stat. Assoc., 49(268), 765–769.
Aydemir, C., and Zorbozan, M. (2012). “Uncertainty analysis of flexural overstrength ratio for RC columns.” J. Struct. Eng., 1042–1053.
Bartlett, M., and MacGregor, J. G. (1996). “Statistical analysis of the compressive strength of concrete in structures.” ACI Mater. J., 93(2), 158–168.
Cosenza, E., Galasso, C., and Maddaloni, G. (2011). “A simplified method for flexural capacity assessment of circular RC cross sections.” Eng. Struct., 33(3), 942–946.
CS.LL.PP. (2008). “DM 14 Gennaio 2008: Norme tecniche per le costruzioni.” Gazzetta Ufficiale della Repubblica Italiana, 29 (in Italian).
Di Sarno, L., Chioccarelli, E., and Cosenza, E. (2011). “Seismic response analysis of an irregular base isolated building.” Bull. Earthquake Eng., 9(5), 1673–1702.
Ellingwood, B., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American National Standard A58: Building code requirements for minimum design loads in buildings and other structures.” U.S. Dept. of Commerce, National Bureau of Standards, Washington, DC.
Ellingwood, B. R., MacGregor, J. G., Galambos, T. V., and Cornell, C. A. (1982). “Probability based load criteria: Load factors and load combination.” J. Struct. Div., 108(5), 978–997.
European Committee for Standardization. (2004a). “Eurocode 2: Design of concrete structures, Part 1.1: General rules and rules for buildings.” Brussels.
European Committee for Standardization. (2004b). “Eurocode 8: Design provisions for earthquake resistance of structures, Part 1.1: General rules, seismic actions and rules for buildings.” Brussels.
Fardis, M. N. (2009). Seismic design, assessment and retrofitting of concrete buildings: Based on EN-Eurocode 8, Springer, Netherlands.
Galambos, T. V., Ellingwood, B. R., MacGregor, J. G., and Cornell, C. A. (1982). “Probability based load criteria: Assessment of current design practice.” J. Struct. Div., 108(5), 959–977.
Iervolino, I., and Galasso, C. (2012). “Comparative assessment of load-resistance factor design for FRP-reinforced cross sections.” Constr. Build. Mater., 34, 151–161.
Italian Organization for Standardization. (2005). “EN 10080: Acciaio d'armatura per calcestruzzo-Acciaio d'armatura saldabile-Generalità.” (in Italian).
Kappos, A. J. (1997). “A comparative assessment of R/C structures designed to the 1995 Eurocode 8 and the 1985 CEB seismic code.” Struct. Des. Tall Build., 6(1), 59–83.
Kappos, A. J., Chryssanthopoulos, M. C., and Dymiotis, C. (1999). “Uncertainty analysis of strength and ductility of confined reinforced concrete members.” Eng. Struct., 21(3), 195–208.
MacGregor, J. G., Mirza, S. A., and Ellingwood, B. R. (1983). “Statistical analysis of resistance of reinforced and prestressed concrete members.” ACI Struct. J., 80(3), 167–176.
Maddaloni, G., Magliulo, G., and Cosenza, E. (2012). “Effect of the seismic input on non-linear response of R/C building structures.” Adv. Struct. Eng., 15(10), 1861–1877.
Magliulo, G., Maddaloni, G., and Cosenza, E. (2007). “Comparison between non-linear dynamic analysis performed according to EC8 and elastic and non-linear static analyses.” Eng. Struct., 29(11), 2893–2900.
Magliulo, G., Maddaloni, G., and Cosenza, E. (2012). “Extension of N2 method to plan irregular buildings considering accidental eccentricity.” Soil Dyn. Earthquake Eng., 43, 69–84.
Mood, M. A., Graybill, F. A., and Boes, D. C. (1974). Introduction to the theory of statistics, 3rd Ed., McGraw-Hill, New York.
Nofal, S., Somja, H., Hjiaj, M., and Nguyen, Q. H. (2013). “Effects of material variability on the ductility of composite beams and overstrength coefficients.” Earthquake Eng. Struct. Dyn., 42(7), 953–972.
Nowak, A. S., and Szerszen, M. M. (2003). “Calibration of design code for buildings (ACI 318). Part 1: Statistical models for resistance.” ACI Struct. J., 100(3), 377–382.
Paulay, T., and Priestley, M. J. N. (1992). Seismic design of reinforced concrete and masonry buildings, John Wiley and Sons, New York.
Somja, H., Nofal, S., Hjiaj, M., and Degee, H. (2013). “Effect of the steel material variability on the seismic capacity design of steel-concrete composite structures: A parametric study.” Bull. Earthquake Eng., 11(4), 1099–1127.
Tumidajski, P. J., Fiore, L., Khodabocus, T., Lachemi, M., and Pari, R. (2006). “Comparison of Weibull and normal distributions for concrete compressive strengths.” Can. J. Civ. Eng., 33(10), 1287–1292.
Zureick, A. H., Bennett, R. M., and Ellingwood, B. R. (2006). “Statistical characterization of fiber-reinforced polymer composite material properties for structural design.” J. Struct. Eng., 1320–1327.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Apr 10, 2013
Accepted: Dec 16, 2013
Published online: Mar 25, 2014
Published in print: Jul 1, 2014
Discussion open until: Aug 25, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.