Characterization of Wall Deflection and Ground Settlement for Irregular-Shaped Excavations with Changes in Corner Configuration
Publication: International Journal of Geomechanics
Volume 23, Issue 1
Abstract
Excavation usually involves the three-dimensional behavior of the supporting wall and nearby ground as indicated by wall and ground movements. In this study, wall deflection and ground settlement behavior with excavation were investigated, focusing on the effect of excavation shape considering various excavation geometries and corner configurations. For this purpose, the three-dimensional finite-element analyses were performed for both regular and irregular excavation shapes. It was found that the wall deflection and surface settlement both increased with an increasing length-to-width ratio for the regular excavation shape. For the irregular excavation shape with a protruding corner, the corner-wall deflection and surface settlement were smaller than the longer-side wall and the regular excavation shape due to the corner stiffening effect. The location of the maximum wall deflection for the longer-side wall shifted to the longer-strut side when a corner existed. The depth of the maximum wall deflection for the longer-side wall was around 0.6 times of the excavation depth and deeper at the corner wall. The primary influence zone of ground settlement behind the wall was 1.0–1.5 times of excavation depth and larger at the corner side due to the combined wall deflection at the corner.
Practical Applications
In this study, the excavation behavior, including wall deflection and nearby ground settlement, for irregular excavation configurations was investigated. It was clearly observed that the wall deflection and ground settlement behaviors for regular and irregular excavation shapes were different. The main differences between the regular and the irregular excavation configurations were seen at the event of a protruding corner, given by the walls of W3 and W4 in the irregular excavation configuration. For the zone of the protruding corner, the depth of the maximum wall lateral deflection became deeper, and the influence range of surface settlement behind the wall was wider than that of the regular excavation configuration case at the same width and configuration. This behavior was attributed to the three-dimensional excavation effect that took place at the protruding corner. Wall deflection and surface settlement profiles were affected by both sides of the corner, and additional strains into the ground were caused. This indicates that adjacent structures near the protruding corner zone can be affected in a wider range and thus should be monitored more carefully. The results and characterized parameters obtained in this study can contribute to further enhancing excavation and wall design as well as to better establishing and networking the field monitoring system. This would be particularly important in urban areas where various types of structures and buildings are heavily located.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was conducted with the support of the National R&D Project for Smart Construction Technology (Grant No. 22SMIP-A158708-03) funded by the Korea Agency for Infrastructure Technology Advancement under the Ministry of Land, Infrastructure and Transport and managed by the Korea Expressway Corporation. It was also supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (Grant No. 2020R1A2C201196613).
References
Bahrami, M., M. I. Khodakarami, and A. Haddad. 2018. “3D numerical investigation of the effect of wall penetration depth on excavations behavior in sand.” Comput. Geotech. 98: 82–92. https://doi.org/10.1016/j.compgeo.2018.02.009.
Blackburn, J. T., and R. J. Finno. 2007. “Three-dimensional responses observed in an internally braced excavation in soft clay.” J. Geotech. Geoenviron. Eng. 133 (11): 1364–1373. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:11(1364).
Brinkgreve, R., E. Engin, and H. Engin. 2010. “Validation of empirical formulas to derive model parameters for sands.” In Numerical methods in geotechnical engineering, edited by T. Benz and S. Nordal, 137–142. Boca Raton, FL: CRC Press.
Brinkgreve, R. B. J., S. Kumarswamy, and W. M. Swolfs, eds. 2020. PLAXIS 3D user manual. Delft, Netherlands: PLAXIS.
Bryson, L. S., and D. G. Zapata-Medina. 2012. “Method for estimating system stiffness for excavation support walls.” J. Geotech. Geoenviron. Eng. 138 (9): 1104–1115. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000683.
Clough, G. W., and T. D. O’Rourke. 1990. “Construction induced movements of in situ walls.” In Proc., Design and Performance of Earth Retaining Structures, 439–470. Reston, VA: ASCE.
Clough, G. W., E. M. Smith, and B. P. Sweeney. 1989. “Movement control of excavation support systems by iterative design.” In Vol. 2 of Proc. ASCE Foundation Engineering: Current Principles and Practices, 869–884. Reston, VA: ASCE.
Dellaria, J., and B. Zitny. 2016. “Combining multiple techniques to complete an urban deep excavation.” In Geotechnical and Structural Engineering Congress, edited by C. Y. Chandran and M. I. Hoit, 351–364. Reston, VA: ASCE.
Elbaz, K., S. L. Shen, Y. Tan, and W. C. Cheng. 2018. “Investigation into performance of deep excavation in sand covered karst: A case report.” Soils Found. 58 (4): 1042–1058. https://doi.org/10.1016/j.sandf.2018.03.012.
Goh, A. T. C., F. Zhang, W. Zhang, and O. Y. S. Chew. 2017a. “Assessment of strut forces for braced excavation in clays from numerical analysis and field measurements.” Comput. Geotech. 86: 141–149. https://doi.org/10.1016/j.compgeo.2017.01.012.
Goh, A. T. C., F. Zhang, W. Zhang, Y. Zhang, and H. Liu. 2017b. “A simple estimation model for 3D braced excavation wall deflection.” Comput. Geotech. 83: 106–113. https://doi.org/10.1016/j.compgeo.2016.10.022.
Goh, A. T. C., R. H. Zhang, W. Wang, L. Wang, H. L. Liu, and W. G. Zhang. 2020. “Numerical study of the effects of groundwater drawdown on ground settlement for excavation in residual soils.” Acta Geotech. 15 (5): 1259–1272. https://doi.org/10.1007/s11440-019-00843-5.
Hoek, E., and E. T. Brown. 1988. “The Hoek–Brown failure criterion-a 1988 update.” In Proc., 15th Canadian Rock Mechanics Symp., 31–38. Toronto: Civil Engineering Dept., Univ. of Toronto.
Hsieh, H. S., W. T. Hsu, and C. J. Chou. 2015. “Incorporating 3-dimensional effect in the design of a small excavation in soft clay.” In Proc., Int. Conf. on Soft Ground Engineering, 669–677. Singapore: Geotechnical Society of Singapore (GeoSS).
Hsieh, H. S., Z. Y. Wang, T. M. Lin, and L. Ge. 2019. “The system stiffness and wall displacement of deep excavation strengthened with cross wall in soft clay.” J. Geoeng. 14 (4): 203–217.
Hsieh, P. G., and C. Y. Ou. 1998. “Shape of ground surface settlement profiles caused by excavation.” Can. Geotech. J. 35 (6): 1004–1017. https://doi.org/10.1139/t98-056.
Hsiung, B. C. B., K. H. Yang, W. Aila, and C. Hung. 2016. “Three-dimensional effects of a deep excavation on wall deflections in loose to medium dense sands.” Comput. Geotech. 80: 138–151. https://doi.org/10.1016/j.compgeo.2016.07.001.
Khoiri, M., and C. Y. Ou. 2013. “Evaluation of deformation parameter for deep excavation in sand through case histories.” Comput. Geotech. 47: 57–67. https://doi.org/10.1016/j.compgeo.2012.06.009.
Kung, G. T. C., E. C. L. Hsiao, and C. H. Juang. 2007. “Evaluation of a simplified small-strain soil model for analysis of excavation-induced movements.” Can. Geotech. J. 44 (6): 726–736. https://doi.org/10.1139/t07-014.
Law, K. H., I. Zubaidah, and H. Roslan. 2016. “3D finite element analysis of deep excavation considering the effect of anisotropic wall stiffness.” In 19th South Asian Geotechnical Conf. Pathum Thani, Thailand: Asian Institute of Technology.
Lee, F. H., K. Y. Yong, K. C. N. Quan, and K. T. Chee. 1998. “Effect of corners in strutted excavations: Field monitoring and case histories.” J. Geotech. Geoenviron. Eng. 124 (4): 339–349. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:4(339).
Li, Y., W. Zhang, and R. Zhang. 2022. “Numerical investigation on performance of braced excavation considering soil stress-induced anisotropy.” Acta Geotech. 17: 563–575. https://doi.org/10.1007/s11440-021-01171-3.
Ou, C. Y., D. C. Chiou, and T. S. Wu. 1996. “Three-dimensional finite element analysis of deep excavations.” J. Geotech. Eng. 122 (5): 337–345. https://doi.org/10.1061/(ASCE)0733-9410(1996)122:5(337).
Ou, C. Y., P. O. Hsieh, and D. C. Chiou. 1993. “Characteristics of ground surface settlement during excavation.” Can. Geotech. J. 30 (5): 758–767. https://doi.org/10.1139/t93-068.
Ou, C. Y., J. T. Liao, and H. D. Lin. 1998. “Performance of diaphragm wall constructed using top-down method.” J. Geotech. Geoenviron. Eng. 124 (9): 798–808. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:9(798).
Peck, R. B. 1969. “Deep excavations and tunneling in soft ground.” In Proc., 7th Int. Conf. on Soil Mechanics and Foundation Engineering, 225–290. Mexico City: Sociedad Mexicana de Mecanica.
Poh, T. Y., and I. H. Wong. 1998. “Effects of construction of diaphragm wall panels on adjacent ground: Field trial.” J. Geotech. Geoenviron. Eng. 124 (8): 749–756. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:8(749).
Russo, G., M. V. Nicotera, and S. Autuori. 2019. “Three-dimensional performance of a deep excavation in sand.” J. Geotech. Geoenviron. Eng. 145 (4): 1–13. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002037.
Wang, J. H., Z. H. Xu, and W. D. Wang. 2010. “Wall and ground movements due to deep excavations in Shanghai soft soils.” J. Geotech. Geoenviron. Eng. 136 (7): 985–994. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000299.
Wong, I. H., and T. Y. Poh. 2000. “Effects of jet grouting on adjacent ground and structures.” J. Geotech. Geoenviron. Eng. 126 (3): 247–256. https://doi.org/10.1061/(ASCE)1090-0241(2000)126:3(247).
Yoo, C., and D. Lee. 2008. “Deep excavation-induced ground surface movement characteristics—A numerical investigation.” Comput. Geotech. 35 (2): 231–252. https://doi.org/10.1016/j.compgeo.2007.05.002.
Yu, J. L., X. Xia, W. Zhang, and L. K. Hu. 2014. “Effect of sandy soil deep excavation engineering on adjacent circumstance.” Chin. J. Geotech. Eng. 36 (1): 311–318.
Zhang, W., A. T. C. Goh, and F. Xuan. 2015. “A simple prediction model for wall deflection caused by braced excavation in clays.” Comput. Geotech. 63: 67–72. https://doi.org/10.1016/j.compgeo.2014.09.001.
Zhang, W., Z. Hou, A. T. C. Goh, and R. Zhang. 2019. “Estimation of strut forces for braced excavation in granular soils from numerical analysis and case histories.” Comput. Geotech. 106: 286–295. https://doi.org/10.1016/j.compgeo.2018.11.006.
Zhang, W., W. Wang, D. Zhou, R. Zhang, A. T. C. Goh, and Z. Hou. 2018a. “Influence of groundwater drawdown on excavation responses—A case history in Bukit Timah granitic residual soils.” J. Rock Mech. Geotech. Eng. 10 (5): 856–864. https://doi.org/10.1016/j.jrmge.2018.04.006.
Zhang, W. G., A. T. C. Goh, K. H. Goh, O. Y. S. Chew, D. Zhou, and R. Zhang. 2018b. “Performance of braced excavation in residual soil with groundwater drawdown.” Underground Space 3 (2): 150–165. https://doi.org/10.1016/j.undsp.2018.03.002.
Zhang, Z.-M., K. Fang, and Z. F. Wu. 2010. “Monitoring analysis of internal forces and deformation of the retaining structure for deep subway station foundation pit in silty sand.” In Proc., Int. Conf. on Mechanic Automation and Control Engineering, 4524–4527. New York: IEEE.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 23 • Issue 1 • January 2023
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Oct 18, 2021
Accepted: Jun 29, 2022
Published online: Nov 4, 2022
Published in print: Jan 1, 2023
Discussion open until: Apr 4, 2023
ASCE Technical Topics:
- Analysis (by type)
- Construction engineering
- Construction methods
- Continuum mechanics
- Displacement (mechanics)
- Engineering fundamentals
- Engineering mechanics
- Excavation
- Finite element method
- Geomechanics
- Geotechnical engineering
- Geotechnical investigation
- Ground motion
- Methodology (by type)
- Numerical methods
- Soil analysis
- Soil dynamics
- Soil mechanics
- Soil properties
- Soil settlement
- Solid mechanics
- Structural engineering
- Structural mechanics
- Structural members
- Structural systems
- Three-dimensional analysis
- Walls
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Shuaihua Ye, Hao Zeng, Wuyu Zhang, Active Earth Pressure Calculation of Equilateral Convex Corners in Excavation Engineering, International Journal of Geomechanics, 10.1061/IJGNAI.GMENG-9459, 24, 8, (2024).
- Taiyi Chen, Guangli Xu, Ying Cong, Surface Settlement of Shallow Shield Tunneling: Face Pressure, Tail-Void Grouting Pressure, and Grout Volume, International Journal of Geomechanics, 10.1061/IJGNAI.GMENG-9011, 24, 6, (2024).
- Qaisar Abbas, Jonghyeog Yoon, Junhwan Lee, A Method for Characterizing Stiffness of a Support System for Excavation Design, International Journal of Geomechanics, 10.1061/IJGNAI.GMENG-8687, 24, 2, (2024).