Effect of Untreated Surface Disbonds on Performance of FRP-Retrofitted Concrete Beams
Publication: Journal of Composites for Construction
Volume 13, Issue 6
Abstract
Retrofitting concrete structures with externally bonded fiber-reinforced polymer (FRP) laminates has become an increasingly common practice. Disbonds at the concrete-FRP interface, if left untreated, may adversely affect the performance of the retrofitted system. Disbonds in the form of surface voids and cracks are the subject of this paper. Voids may occur due to poor compaction or defective formwork, or in the form of air entrapment between resin and FRP laminate during application. Cracks, on the other hand, generally result from loading. This study is comprised of a detailed experimental program and a nonlinear finite-element analysis. In the experiments, surface cracks were simulated by cutting slits in concrete, herein termed as surface cuts. The study shows that leaving surface disbonds untreated, within the considered range of disbond variables, does not have a significant impact on the overall structural performance. A threshold of 12.7 mm for void diameter was deemed conservative for structural performance. On the other hand, 38 mm spacing was considered an appropriate threshold for epoxy injection in crack widths between 0.25 and 0.8 mm. Hence, conservative thresholds in current practice may be revised accordingly, unless considered necessary to avoid environmental effects.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was sponsored by the American Association of State Highway and Transportation Officials in cooperation with the Federal Highway Administration, conducted as part of the National Cooperative Highway Research Program (NCHRP) Grant No. UNSPECIFIED10-59B, administered by the Transportation Research Board of the National Research Council, Senior Program Officers, Mr. David Beal, and Dr. Amir Hanna. The tests were carried out at the Structures and Construction Laboratory of the Florida International University. The contributions of the subconsultants, Dr. Mohsen Shahawy, Dr. Vistasp Karbhari, and Dr. Antonio Nanni is greatly acknowledged. The writers are also grateful to Sika Corp. and Hughes Brothers, Inc. for providing some of the materials for the tests. Findings and opinions expressed here, however, are those of the writers alone, and not necessarily the views of the sponsoring agencies.
References
ACI Committee 440. (2008). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.” ACI 440.2R-08, American Concrete Institute, Detroit.
ANSYS 8.0. (2003). ANSYS Inc., Canonsburg, Pa.
Arduini, M., and Nanni, A. (1997). “Behavior of precracked RC beams strengthened with carbon FRP sheets.” J. Compos. Constr., 1(2), 63–70.
Delaney, J. C., and Karbhari, V. M. (2006). “The assessment of aspects related to defect criticality in CFRP strengthened concrete flexural members.” Rep. No. SSRP 06/11, Dept. of Structural Engineering, Univ. of California-San Diego, La Jolla, Calif.
ICRI/ACI. (1999). Concrete repair manual, American Concrete Institute, Detroit.
Kaiser, H. (2002). “Assessment of defect criticality and non-destructive monitoring of CFRP-rehabilitated civil structures.” MS thesis, Univ. of California-San Diego, La Jolla, Calif.
Kalayci, A. S. (2008). “Development of surface flaw thresholds for pre-cured fiber reinforced polymer and groove size tolerance for near surface mounted fiber reinforced polymer systems.” Ph.D. thesis, Florida Int. Univ., Miami.
Mirmiran, A., Shahawy, M., Nanni, A., and Karbhari, V. (2004). “Bonded repair and retrofit of concrete structures using FRP composites-recommended construction specifications and process control manual.” NCHRP Rep. No. 514, Transportation Research Board, Washington, D.C.
Mirmiran, A., Shahawy, M., Nanni, A., Karbhari, V., Yalim, B., and Kalayci, A. S. (2008). “Recommended construction specifications and process control manual for repair and retrofit of concrete structures using bonded FRP composites.” NCHRP Rep. No. 609, Transportation Research Board, Washington, D.C.
Myers, J. J., and Ekenel, M. (2005). “Effect of environmental conditions during installation process on bond strength between CFRP laminate and concrete substrate.” Proc., 7th Int. Symp. on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, (FRPRCS-7), American Concrete Institute, Detroit.
Navada, R. (2004). “A fracture mechanics approach to assessment of defect criticality in FRP rehabilitated concrete.” MS thesis, Univ. of California-San Diego, La Jolla, Calif.
Puliyadi, S. (2001). “Performance of CFRP sheet strengthened reinforced concrete beams in the presence of delamination and lap splice.” MS thesis, Univ. of Missouri, Rolla, Mo.
Shahawy, M. A., Beitelman, T., Arockiasamy, M., and Sowrirajan, R. (1996). “Experimental investigation on structural repair and strengthening of damaged prestressed concrete slabs utilizing externally bonded carbon laminates.” Composites, Part B, 27(3–4), 217–224.
Telang, N. M., Dumlao, C., Mehrabi, A. B., Ciolko, A. T., and Gutierrez, J. (2004). “Field inspection of service FRP bridge decks.” NCHRP Rep. No. 564, Transportation Research Board, Washington, D.C.
Thanoon, W. A., Jaafar, M. S., Razali, M., Kadir, A., and Noorzaei, J. (2005). “Repair and structural performance of initially cracked reinforced concrete slabs.” Constr. Build. Mater., 19(8), 595–603.
Yalim, B. (2008). “Development of thresholds for surface preparation in repair systems with wet lay-up fiber reinforced polymers.” Ph.D. thesis, Florida Int. Univ., Miami.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Aug 2, 2008
Accepted: Feb 24, 2009
Published online: Nov 13, 2009
Published in print: Dec 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.