Successful Application of CLSM on a Weak Pavement Base/Subgrade for Heavy Truck Traffic
Publication: Journal of Performance of Constructed Facilities
Volume 21, Issue 1
Abstract
Lack of proper pavement base and subgrade compaction leads to premature failures that account for millions of dollars in damages. Controlled low-strength material (CLSM) concrete was introduced in this study as pavement base material near a manhole where proper compaction is unachievable. Rut-resistant stone matrix asphalt was placed on top of the CLSM as a wearing surface layer. Dynamic cone penetrometer (DCP) testing was used to monitor CLSM construction. One day after placing, the CLSM gained sufficient strength to support construction traffic. Further, DCP results indicated that the CLSM possessed uniform characteristics of concrete that could improve the load-bearing capacity and serviceability of the pavement near the manhole. After 18 months of heavy truck traffic, maximum rutting was , well below the failure criteria of . Based on cost and performance, CLSM concrete has the potential to improve problematic areas in pavement.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was partly support by the Kaohsiung City government. The writers express their sincere thanks to Dr. D. H. Chen and Mr. S. C. Chen for his editorial comments and suggestions. The assistance of Q. Z. Liao, Z. R. Zhong, J. H. Qiu, and M. W. Weng in some portions of the experiments is greatly appreciated.
References
ACI Committee 229. (1994). “Controlled low-strength materials (CLSM) (ACI 229R-94).” Concr. Int., 16(7), 58–64.
Adaska, W. S. (1997). “Controlled low-strength materials.” Concr. Int., 19(4), 41–43.
American Society for Testing and Materials (ASTM). (1989). “Standard test method for resistance to plastic flow of bituminous mixtures using marshall apparatus (ASTM D).” 1559–89.
Amon, J. A. (1990). “Controlled low-strength material: Concrete’s low-cost cousin.” Constr. Specifier, 43(12), 98–101.
Brown, E. R., Mallick, R. B., Haddock, J. E., and Bukowski, J. (1997). “Performance of stone matrix asphalt (SMA) mixture in the United States.” NCAT Rep. No.97-1, National Center for Asphalt Technology of Auburn Univ., Auburn, Ala.
Chai, S. W., and Shieh, P. C. (1999). “Additives in low strength, high flowbility concrete for backfilling.” Taiwan Construction Research Institute, Taipei, Taiwan.
Chen, D. H., Wang, J. N., and Bilyeu, J. (2001). “Application of the DCP in evaluation of base and subgrade layers.” Transportation Research Record. 1764, Transportation Research Board, Washington, D.C., pp. 1–10.
Du, L. X., Folliard, K. J., and Treio, D. (2002). “Effects of constituent materials and quantities on water demand and compressive strength of controlled low-strength material.” J. Mater. Civ. Eng., 4(6), 485–495.
Green, B. H. (1998). “Fly-ash-based controlled low-strength material (CLSM) used for critical microtunneling applications.” ASTM Spec. Tech. Publ., No. 1331, 151–164.
Hitch, J. L. (1998). “Test methods for controlled low-strength material (CLSM): Past, present, and future.” ASTM Spec. Tech. Publ., No. 1331, 3–10.
Hook, W., and Clem, D. A. (1998). “Innovative uses of controlled low strength material (CLSM) in Colorado.” ASTM Spec. Tech. Publ., No. 1331, 137–150.
Howard, A. K. (1998). “Proposed standard practice for installing buried pipe using flowable fill.” ASTM Spec. Tech. Publ., No. 1331, 285–295.
Lin, D. F., and Wang, H. Y. (2005). “Forensic investigation of the ultra-thin whitetopping (UTW) failures in Taiwan.” J. Perform. Constr. Facil., 19(2), 165–171.
Pierce, C. E., Gassman, S. L., and Richards, T. M. (2002). “Long-term strength development of controlled low-strength material.” ACI Mater. J., 99(2), 2002, 157–164.
Scherocman, J. A. (1997). “The construction and performance of stone mastic asphalt pavements in the United States.” Proc., 8th Int. Conf. on Asphalt Pavements, Int. Society for Asphalt Pavement, Seattle, Wash. 1205–1224.
Sheen, Y. L., Chen, S. J., and Wang, J. T. (2001). “Application of low strength, high flowbility concrete on utility backfilling.” Proc., 11th Pavement Engineering Conf., Chinese Institute of Civil and Hydraulic Engineering, Kaohsiung, Taiwan, 665–672.
Siekmeier, J. A., Young, D., and Beberg, D. (2000). “Comparison of the dynamic cone penetrometer with other tests during subgrade and granular base characterization in Minnesota. Nondestructive testing of pavements and backcalculation of moduli.” Vol. 3, ASTM Spec. Tech. Publ., No. 1375, 175–188.
Snethen, D. R., and Benson, J. M. (1998). “Construction of CLSM approach embankment to minimize the bump at the end of the bridge.” ASTM Spec. Tech. Publ.No. 1331, 165–179.
Taiwan Highway Bureau (THB). (1997). Highway Construction Specification.
Webster, S. L., Grau, R. H., and Williams, R. P. (1992). “Description and application of dual mass dynamic cone penetrometer.” Instruction, Rep. No. GL-92-3, U.S. Army Engineer Waterways Experiment Station.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Apr 22, 2005
Accepted: Dec 20, 2005
Published online: Feb 1, 2007
Published in print: Feb 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.