Validation of Cyclic Void Growth Model for Fracture Initiation in Blunt Notch and Dogbone Steel Specimens
Publication: Journal of Structural Engineering
Volume 134, Issue 9
Abstract
Tests and finite-element analyses of blunt notch and dogbone specimens are presented to demonstrate the application and validation of the cyclic void growth model (CVGM) to evaluate the initiation of ductile fracture under cyclic loading in steel structures. Modeling concepts and procedures for characterizing the CVGM material parameters using notched bar tests are described. Accuracy of the model is validated through a series of cyclic tests of 14 blunt notch compact fracture specimens and four dogbone specimens. Four types of moderate to high strength structural steels are investigated (two types of A572-Grade 50, A514-Grade 110, HPS70W). The test specimens reflect stress and strain conditions encountered in structural steel components and provide sufficiently strong stress and strain gradients to validate the characteristic length assumptions in the model. Detailed finite-element analyses that employ the CVGM criterion are shown to predict fracture with good accuracy across the specimen geometries, steel types, and loading histories.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This paper is based upon research supported by the National Science Foundation under the U.S. Japan Cooperative Research for Urban Earthquake Disaster Mitigation initiative (Grant No. NSFCMS 9988902). The advice and guidance provided by Robert Dodds (University of Illinois), and Reiner Dauskardt (Stanford University) are gratefully acknowledged. Additional support was provided by the Steel Structures Development Center of the Nippon Steel Corporation (Futtsu, Japan), which provided steel materials, machining services, and fracture data, and by donations of steel material from the Garry Steel Company (Oakland, Calif.) and the ATLSS Engineering Research Center (Bethlehem, PA). Computational simulations and input from Ben Fell (UC Davis) is greatly appreciated.
References
ABAQUS. (1998). User’s manual, ver. 5.8, Hibbitt, Karlsson, and Sorensen, Inc., Providence, R.I.
Anderson, T. L. (1995). Fracture mechanics, 2nd Ed., CRC Press, Boca Raton, Fla.
ASTM. (1997). “Standard test method for the measurement of fracture toughness.” E1820-01, American Society for Testing and Materials.
Chi, W.-M. (2000). “Prediction of steel connection failure using computational fracture mechanics.” Ph.D. thesis, Stanford Univ., Stanford, Calif.
Coffin, L. F., Jr. (1954). “A study of the effects of cyclic thermal stresses on a ductile metal.” Trans. ASME, 76, 931–950.
Cowie, J. G., Azrin, M., and Olson, G. B. (1989). “Microvoid formation during shear deformation of ultrahigh strength steels.” Metall. Trans. A, 20A, 143–153.
Hancock, J. W., and Mackenzie, A. C. (1976) “On the mechanics of ductile failure in high-strength steel subjected to multi-axial stress-states.” J. Mech. Phys. Solids, 24(3), 147–169.
Iwai, S., Park, Y.-S., Nonaka, T., and Kameda, H. (1992). “Very low cycle fatigue tests of steel angle members under earthquake loading.” Proc., of the Tenth World Conf. in Earthquake Engineering, Vol. 5, Balkema, Rotterdam, 2879–2884.
Kanvinde, A. M., and Deierlein, G. G. (2004). “Micromechanical simulation of earthquake induced fracture in steel structures.” Technical Rep. No. 145, John A. Blume Earthquake Engineering Center, Stanford Univ., Stanford, Calif.
Kanvinde, A. M., and Deierlein, G. G. (2006). “The void growth model and the stress modified critical strain model to predict ductile fracture in structural steels.” J. Struct. Eng., 132(12), 1907–1918.
Kanvinde, A. M., and Deierlein, G. G. (2007a). “Cyclic void growth model to assess ductile fracture initiation in structural steels due to ultra low cycle fatigue.” J. Eng. Mech., 133(6), 701–712.
Kanvinde, A. M., and Deierlein, G. G. (2007b). “Finite-element simulation of ductile fracture in reduced section pull plates using micromechanics fracture models.” J. Struct. Eng., 133(5), 656–664.
Kuwamura, H., and Yamamoto, K. (1997). “Ductile crack as a trigger of brittle fracture in steel.” J. Struct. Eng., 123(6), 729–735
Lemaitré, J., and Chaboche, J.-L. (1990). Mechanics of solid materials, Cambridge Univ. Press, Cambridge, U.K.
Panontin, T. L., and Sheppard, S. D. (1995) “The relationship between constraint and ductile fracture initiation as defined by micromechanical analyses.” Fracture mechanics: 26th volume, ASTM STP 1256, 54–85.
Rice, J. R., and Tracey, D. M. (1969). “On the ductile enlargement of voids in triaxial stress fields.” J. Mech. Phys. Solids, 35, 201–217.
Rousselier, G. (1987). “Ductile fracture models and their potential in local approach of fracture.” Nucl. Eng. Des., 105(1), 113–120.
Tatsuo, E., Koichi, M., Kiyohumi, T., Kakuichi, K., and Masanori, M. (1974). “Damage evaluation of metals for random of varying loading—Three aspects of rain flow method.” Symp. Proc., Mechanical Behavior of Materials, Society of Materials Scientists, Kyoto, Japan, 371–380.
Uriz, P., and Mahin, S. (2004). “Seismic performance assessment of concentrically braced steel frames.” Proc., 13th World Conf. on Earthquake Engineering (CD-ROM), Vancouver, Canada, Paper #1639.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Jul 13, 2007
Accepted: Mar 21, 2008
Published online: Sep 1, 2008
Published in print: Sep 2008
Notes
Note. Associate Editor: Sashi K. Kunnath
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.