Inelastic Limit States Design Part II: Three‐Dimensional Frame Study
Publication: Journal of Structural Engineering
Volume 118, Issue 9
Abstract
A design study of a three‐dimensional 22‐story frame is presented to demonstrate the use of second‐order inelastic analysis in load and resistance factor design. This study is a follow‐up to a set of low‐rise planar frame studies presented in a companion paper. The limit state behavior of the inelastic design is evaluated with respect to strength and serviceability requirements. The strength requirements include investigating the inelastic rotation demands, effects of residual stresses, and conformance with a limit states design specification. The inelastic design is also compared to a design obtained using conventional elastic methods of analysis. The study indicates that with computer‐aided engineering, second‐order inelastic analysis provides a feasible alternative for designing steel structures of substantial size. It also concludes that existing limitations of current analytical techniques, e.g., the inability to model torsional‐flexural instabilities of beam‐columns, need to be overcome before inelastic analysis‐design approaches such as that presented can be generally applied.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American national standard minimum design loads for buildings and other structures. (1982). ANSI A58.1 American National Standards Institute, New York, N.Y.
2.
Cheong‐Sait‐Moy, F. (1976). “Stiffness design of unbraced steel frames.” Engrg. J., AISC, 13(1), 8–10.
3.
Commentary on the AISC LRFD specification (1986). First Ed., American Institute of Steel Construction, Chicago, Ill.
4.
Cuk, P. E., and Trahair, N. S. (1981). “Elastic buckling of beam‐columns with unequal end moments.” Civ. Engrg. Trans., Instn. Engrs., Australia, CE23(3), 166–171.
5.
Ellingwood, B. (1989). “Serviceability guidelines for steel structures.” Engrg. J., AISC, 26(1), 1–8.
6.
Galambos, T. V. (1968). “Deformation and energy absorption capacity of steel structures.” Steel Research for Construction Bulletin No. 8, American Iron and Steel Institute, New York, N.Y.
7.
Galambos, T. V., ed. (1988). Guide to stability design criteria for metal structures. 4th Ed., Structural Stability Research Council, John Wiley and Sons, New York, N.Y.
8.
Galambos, T. V., and Ellingwood, B. (1986). “Serviceability limit states: Deflection.” J. Struct. Engrg., ASCE, 112(1), 67–84.
9.
Hsieh, S.‐H., Deierlein, G. G., McGuire, W., and Abel, J. F. (1989). “Technical manual for CU‐STAND.” Struct. Engrg. Report No. 89‐13, School of Civil and Environmental Engrg., Cornell University, Ithaca, N.Y.
10.
Johnston, B. G., ed. (1966). Guide to design critria for metal compression members. 2d Ed., Column Research Council, John Wiley & Sons, Inc., New York, N.Y.
11.
Kemp, A. R. (1986). “Factors affecting the rotation capacity of plastically designed members.” The Struct., Engr., 64B(2), 28–35.
12.
Liapunov, S. (1974). “Ultimate strength of multistory steel rigid frames.” J. Struct. Div., ASCE, 100(8), 1643–1655.
13.
Load and resistance factor design specification for structural steel buildings. (1986). 1st Ed., American Institute of Steel Construction, Chicago, Ill.
14.
Lu, L. W., Ozer, E., Daniels, J. H., Okten, O. S., and Morino, S. (1975). “Frame stability and design of columns in unbraced multistory steel frames.” Fritz Engineering Laboratory Report No. 375.2, Lehigh University, Bethlehem, Pa.
15.
“Steel structures for buildings (limit states designs).” (1984). CAN‐S16.1‐M84.CSA, Canadian Standards Association, Rexdale, Ontario, Canada.
16.
Trahair, N. S., and Bradford, M. A. (1988). The behavior and design of steel structures. 2d Ed., Chapman and Hall, New York, N.Y.
17.
Ziemian, R. D. (1990). “Advanced methods of inelastic analysis in the limit states design of steel structures,” thesis presented to Cornell University at Ithaca, N.Y. in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
18.
Ziemian, R. D., McGuire, W., and Deierlein, G. G. (199?), “Inelastic limit states design Part I: Planar frame studies.” J. Struct. Engrg., 118(9), 2532–2549.
Information & Authors
Information
Published In
Copyright
Copyright © 1992 ASCE.
History
Published online: Sep 1, 1992
Published in print: Sep 1992
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.