Inelastic Limit States Design. Part I: Planar Frame Studies
Publication: Journal of Structural Engineering
Volume 118, Issue 9
Abstract
In conjunction with load and resistance factor design specifications, advanced methods of inelastic analysis afford the opportunity to design steel structures based on realistic assessments of limit state behavior. This paper presents a summary of a study of the in‐plane behavior of a series of low‐rise frames. Designs are obtained that rely on a second‐order inelastic analysis to demonstrate that the frame and its members are adequate in resisting the effects of factored loads. The inelastic designs are compared with designs obtained using conventional elastic methods of design. A representative inelastic design is further evaluated with respect to strength and serviceability limit state behavior, including conformance with current load and resistance factor design specification provisions. The accuracy and reliability of using a second‐order concentrated plasticity analysis to model system behavior are also established. The investigation indicates that second‐order inelastic analysis can be used effectively to design steel structures. It also identifies the benefits, current status, and future directions for applying inelastic analysis in design. Use of the inelastic analysis/design method for a three‐dimensional multistory frame is presented in a companion paper.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Australian standard, steel structures. (1990). Standards Association of Australia, Sydney, Australia.
2.
Code of standard practice for steel buildings and bridges. (1986). American Institute of Steel Construction, Chicago, Ill.
3.
Ellingwood, B., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American National Standard A58.” National Bureau of Standards Special Publication 577, U.S. Department of Commerce, Washington, D.C.
4.
Eurocode No. 3, design of steel structures. (1990). Commission of the European Communities, Brussels, Belgium.
5.
Hsieh, S.‐H., Deierlein, G. G., McGuire, W., and Abel, J. F. (1989). “Technical manual for CU‐STAND.” Struct. Engrg. Report No. 89‐13, School of Civil and Environmental Engineering, Cornell University, Ithaca, N.Y.
6.
Iffland, J. S. B., and Birnstiel, C. (1982). “Stability design procedures for building frameworks.” ASIC Project No. 21.62, American Institute of Steel Construction, Chicago, Ill.
7.
Kemp, A. R. (1985). “Interaction of plastic local and lateral buckling.” J. Struct. Engrg., ASCE, 111(10), 2181–2196.
8.
Kemp, A. R. (1986). “Factors affecting the rotation capacity of plastically designed members.” The Struct. Engr., 64B(2), 28–35.
9.
Lay, M. G., and Galambos, T. V. (1967). “Inelastic beams under moment gradient.” J. Struct. Div., ASCE, 93(1), 381–399.
10.
Load and resistance factor design specification for structural steel buildings. (1986). 1st Ed., American Institute of Steel Construction, Chicago, Ill.
11.
White, D. W. (1984). “Material and geometrical nonlinear analysis of local planar behavior in steel frames using interactive computer graphics,” thesis presented to Cornell University, at Ithaca, N.Y., in partial fulfillment of the requirements for the degree of Master of Science.
12.
Yura, J. A., Galambos, T. V., and Ravindra, M. K. (1978). “The bending resistance of steel beams.” J. Struct. Div., ASCE, 104(9), 1355–1370.
13.
Ziemian, R. D. (1990). “Advanced methods of inelastic analysis in the limit states design of steel structures,” thesis presented to Cornell University, at Ithaca, N.Y., in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
14.
Ziemian, R. D., McGuire, W., and Deierlein, G. G. (1992). “Inelastic limit states design. Part II: Three‐dimensional frame study.” J. of Struct. Engrg., ASCE, 118(9), 2550–2568.
Information & Authors
Information
Published In
Copyright
Copyright © 1992 ASCE.
History
Published online: Sep 1, 1992
Published in print: Sep 1992
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.