Chapter 11
Bridge-Scour Prevention and Countermeasures
Publication: Sedimentation Engineering: Processes, Measurements, Modeling, and Practice
Get full access to this article
View all available purchase options and get full access to this chapter.
REFERENCES
Acheson, A. R. (1968). “River control and drainage in New Zealand and some comparisons with overseas practices.” Ministry of Works, Wellington, New Zealand.
Ahmad, M. (1951). “Spacing and projection of spurs for bank protection.” Civil Engineering and Public Work Review, 172–174, April, 256–258.
Atayee, A. T., Pagan-Ortiz, J. E., Jones, J. S., and Kilgore, R. T. (1993). “A Study of Riprap as a Scour Protection for Spill- Through Abutments.” ASCE Hydraulic Conference, San Francisco, Calif., 973–978.
Austroads. (1994). Waterway design—A guide to the hydraulic design of bridges, culverts and floodways, Austroads, Sydney, Australia.
Barkdoll, B. D., Ettema, R., and Odgaard, A. J. (1999). “Sediment control at lateral diversions: Limits and enhancements to vane use.” Journal of Hydraulic Engineering, ASCE, 125(8), 862–870.
Bertoldi, D. A., Jones, J. S., Stein, S. M., Kilgore, R. T., and Atayee, A. T. (1996). “An experimental study of scour protection alternatives at bridge piers.” Rep. No. FHWA-RD- 95-187, Turner-Fairbank Highway Research Center, Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Bonasoundas, M. (1973). “Strömungsvorgang und kolkproblem.” Report No. 28, Oskar v. Miller Institut, Tech. Univ. Munich, Germany.
Bradley, J. N. (1978). “Hydraulics of bridge waterways.” Hydraulic Design Series No. 1, Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Breusers, H. N. C., Nicollet, G., and Shen, H. W. (1977). “Local scour around cylindrical piers.” Journal of Hydraulic Research, 15(3), 211–252.
Breusers, H. N. C., and Raudkivi, A. J. (1991). “Scouring.” Hydraulic Structures Design Manual No. 2, IAHR, Balkema., Rotterdam, The Netherlands.
Brown, S. A., and Clyde, E. S. (1989). “Design of riprap revetment.” Hydraulic Engineering Circular 11 (HEC-11), Report No. FHWA-IP-89-016, Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Brown, S. A., McQuivey, R. S., and Keefer, T. N. (1981). “Stream channel degradation and aggradation analysis of impacts to highway crossings.” Final Rep. No. FHWA-RD-80-159, Federal Highway Administration, U. S. Department of Transportation, Washington, D. C.
Central Board of Irrigation and Power (CBIP). (1989). “River behaviour management and training.” Publication No. 204, Vol. 1, Sharma C. V. J., Saxema K. R., and Rao M.K., eds., Central Board of Irrigation and Power, New Delhi, India.
Chabert, J., and Engeldinger, P. (1956). Etude des affouillements autour des piles des ponts, Laboratoire d’Hydraulique, Chatou, France (in French).
Chang, F. F. M., and Karim, M. (1972). “An experimental study of reducing scour around bridge piers using piles.” Report, South Dakota Department of Highways, Pierre, S.D.
Chiew, Y. M. (1992). “Scour protection at bridge piers.” Journal of Hydraulic Engineering, ASCE, 118(9), 1260–1269.
Chiew, Y. M. (1995). “Mechanics of riprap failure at bridge piers.” Journal of Hydraulic Engineering, ASCE, 121(9), 635–643.
Coleman, S. E., and Melville, B. W. (2001). “Case study: New Zealand bridge scour experiences.” Journal of Hydraulic Engineering, ASCE, 127(7), 535–546.
Coleman, S. E., Melville, B. W., and Lauchlan, C. S. (2000). “Bealey Bridge scour failure.” Scour of Foundations, Proc., Int. Symp., Briaud J. (ed.), Department of Civil Engineering, Texas A & M University, College Station, Tex., 387–393.
Copeland, R. R. (1983). Bank protection techniques using spur dikes. Hydraulics Laboratory, U.S. Army Engineer Waterways Experiment Station, Vicksburg, Miss.
Croad, R. N. (1989). “Investigation of the pre-excavation of the abutment scour hole at bridge abutments.” Rep. 89-A9303, Central Laboratories, Works and Development Services Corporation (NZ), Lower Hutt, New Zealand.
Croad, R. N. (1997). “Protection from scour of bridge piers using riprap.” Transit New Zealand Research Rep. No. PR3-0071, Works Consultancy Services Ltd., Central Laboratories, Lower Hutt, New Zealand.
Dargahi, B. (1982). “Local scour at bridge piers—A review of theory and practice.” Bulletin No. TRITA-VBI-114, Hydraulics Laboratory, Royal Institute of Technology, Stockholm, Sweden.
Dargahi, B. (1987). “Flow field and local scouring around a cylinder.” Bulletin No. 137, Royal Institute of Technology Hydraulics Laboratory, Stockholm, Sweden.
Dargahi, B. (1989). “The turbulent flow field around a circular cylinder.” Experiments in Fluids, 8, 1–12.
Dargahi, B. (1990). “Controlling mechanism of local scouring.” Journal of Hydraulic Engineering, ASCE, 116(10), 1197–1214.
Diehl, T. H. (1997). “Potential drift accumulation at bridges.” Rep. No. FHWA-RD-97-28, Federal Highway Administration, Washington, D.C.
Engels, H. (1929). “Chapter V: Experiments pertaining to the protection of bridge piers against undermining.” Hydraulic Laboratory Practice, ASME, New York.
Escarameia, M., and May, R. W. P. (1992). “Channel protection— Turbulence downstream of structures.” Rep. SR 313, HR Wallingford, Howbery Park, Wallingford, U.K.
Ettema, R. (1980). “Scour at bridge piers.” Rep. No. 216, School of Engineering, The University of Auckland, Auckland, New Zealand.
Eve, N. (1999). “Riprap protection at bridge abutments.” ME thesis, The University of Auckland, Auckland, New Zealand.
Farraday, R. V., and Charlton, F. G. (1983). Hydraulic factors in bridge design. Hydraulics Research Station, Wallingford, U.K.
Fotherby, L. M. (1992). “Footings, mats, grout bags, and tetrapods: Protection methods against local scour at bridge piers.” MS thesis, Colorado State University, Fort Collins, Colo.
Fotherby, L. M., and Ruff, J. F. (1996). “Riprap and concrete armor to prevent pier scour.” Proc., North American Water and Environment Congress, ASCE, Reston, Va.
Gales, R. R. (1938). “The principles of river-training for railway bridges, and their application to the case of the Harding Bridge over the Lower Ganges at Sara.” Journal of the Institution of Civil Engineers, 10(2), 136–224.
Grant, R. J. (1948). “Channel improvements in alluvial streams.” Proceedings, New Zealand Institution of Engineers, 34, 231–279.
Gregorius, B. H. (1985). “Waterway design procedures— Guidelines.” Civil Division Publication, Ministry of Works and Development, Hamilton, New Zealand.
Harris, J. D. (1988). “Chapter I: Hydraulic design of bridges.” MTC Drainage Manual, Drainage and Hydrology Section, Ontario Ministry of Transportation, Downsview, Ont.
Harvey, M. D., and Sing, E. F. (1989). “The effects of bank protection on river morphology.” Proc., National Conference on Hydraulic Engineering, Ports M. A., ed., ASCE, New York, 212–217.
Hjorth, P. (1975). “Studies on the nature of local scour.” Bulletin, Series A, No. 46, Institutionen for teknisk vattenresurslara, Lund, Sweden.
Johnson, P. A., Hey, R. D., Horst, M. W., and Hess, A. J. (2001). “Aggradation at bridges.” Journal of Hydraulic Engineering, ASCE, 127(2), 154–157.
Jones, J. S., Bertoldi, D. A., and Stein, S. (1995). “Alternative scour countermeasures.” Proc., Hydraulic Engineering ‘95, Espey W. H. Jr. and Combs P. S., eds., ASCE, New York, 1819–1823.
Kandasamy, J. K. (1989). “Abutment scour.” Rep. No. 458, School of Engineering, The University of Auckland, Auckland, New Zealand.
Karaki, S. S. (1959). “Hydraulic model study of spur dikes for highway bridge openings.” Rep. CER59SSK36, Civil Engineering section, Colorado State University, Fort Collins, Colo.
Karaki, S. S. (1961). “Laboratory study of spur dikes for highway bridge protection.” Bulletin 286, Highway Research Board, Washington, D.C.
Kwan, T. F. (1984). “Study of abutment scour.” Rep. No. 328, School of Engineering, The University of Auckland, Auckland, New Zealand.
Kwan, T. F. (1988). “A study of abutment scour.” Rep. No. 451, School of Engineering, The University of Auckland, Auckland, New Zealand.
Lagasse, P. F., Schall, J. D., Johnson, F. M., Richardson, E. V., and Chang, F. (1995). “Stream stability at highway structures.” Hydraulic Engineering Circular No. 20 (HEC-20), Rep. No. FHWA-IP-90-014, Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Lagasse, P. F., Schumm, S. A., and Zevenbergen, L. W. (1997). “Quantitative techniques for stream stability analysis.” Proc., 27th Congress of the International Association for Hydraulic Research, A147–A153.
Lagasse, P. F., Zevenbergen, L. W., Schall, J. D., and Clopper, P. E. (2001). “Bridge scour and stream instability countermeasures: Experience, selection, and design guidance.” Hydraulic Engineering Circular No. 23 (HEC-23), Report No. FHWANHI- 01-003, 2nd ed., Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Lane, E. W. (1955). “Design of stable channels.” Transactions, ASCE, 120, Paper No. 2776, 1234–1279.
Lauchlan, C. S. (1999). “Countermeasures for pier scour.” PhD thesis, The University of Auckland, Auckland, New Zealand.
Levi, E., and Luna, H. (1961). “Dispositifs pour reduire l’affouillement au pied des piles de pont.” Proc., 9th I.A.H.R. Congress, IAHR, Madrid, Spain, 1061–1069.
Lewis, G. L. (1972). “Riprap protection of bridge footings.” PhD thesis, Colorado State University, Fort Collins, Colo.
Lim, F. H., and Chiew, Y.M. (1997). “Stability of riprap layer under live-bed conditions.” Conference on Management of Landscapes disturbed by Channel Incision, Wang S. Y., Langendoen E. J., and Shields F. D. Jr., eds., Center for the Computational Hydroscience and Engineering, University of Mississippi, Oxford, Mississippi, 277–287.
Macky, G.H. (1986). “Model testing of bridge abutment scour protection.” Rep. 3-86/12, Central Laboratories, Ministry of Works and Development, Lower Hutt, New Zealand.
Maynord, S.,T. (1995). “Gabion-mattress channel-protection design.” Journal of Hydraulic Engineering, ASCE, 121(7), 519–522.
Maynord, S.,T. (1996). “Toe-scour estimation in stabilised bend-ways.” Journal of Hydraulic Engineering, 122(8), 460–464.
Maza Alvarez, J. A. (1968). “Scour in natural channels.” Rep. No. 114, Miguel-Rodriguez A. J., translator, School of Engineering, The University of Auckland, Auckland, New Zealand.
Maza Alvarez, J. A. (1989). “Design of groynes and spur dikes.” Proc., 1989 National Conference on Hydraulic Engineering, 296–301.
Melville, B. W., and Coleman, S. E. (2000). Bridge scour. Water Resources Publications, Highlands Ranch, Colo.
Melville, B. W., and Hadfield, A. C. (1999). “Use of sacrificial piles as pier scour countermeasures.” Journal of Hydraulic Engineering, ASCE, 125(11), 1221–1224.
Ministry of Works and Development (MWD). (1979). “Code of practice for the design of bridge waterways.” Civil Division Publication CDP 705/C, Ministry of Works and Development, Wellington, New Zealand.
Neill, C. R., ed. (1973). Guide to bridge hydraulics. Roads and Transportation Assoc. of Canada, University of Toronto Press, Toronto.
Odgaard, A. J., and Kennedy, J. F. (1983). “River bend bank protection by submerged vanes.” Journal of Hydraulic Engineering, ASCE, 109(8), 1161–1173.
Odgaard, A. J., and Spoljaric, A. (1986). “Sediment control by submerged vanes.” Journal of Hydraulic Engineering, ASCE, 112(12), 1164–1181.
Odgaard, A. J., and Wang, Y. (1987). “Scour prevention at bridge piers.” Proc., National Conference on Hydraulic Engineering, ASCE, New York, 523–527.
Odgaard, A. J., and Wang, Y. (1991a). “Sediment management with submerged vanes. I: Theory.” Journal of Hydraulic Engineering, ASCE, 117(3), 267–283.
Odgaard, A. J., and Wang, Y. (1991b). “Sediment management with submerged vanes. II: Applications.” Journal of Hydraulic Engineering, ASCE, 117(3), 284–302.
Pagan-Ortiz, J. E. (1991). “Stability of rock riprap for protection at the toe of abutments located at the flood plain.” Rep. No. FHWARD- 91-057, Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Paice, C., and Hey, R. (1993). “The control and monitoring of local scour at bridge piers.” Proc., Hydraulic Engineering Conference, ASCE, New York, 1061–1066.
Parker, G., Toro-Escobar, C., and Voigt, R. L., Jr. (1998). “Countermeasures to protect bridge piers from scour.” Draft Final Report (Project NCHRP 24-7) prepared for National Co-operative Highway Research Program, University of Minnesota, Minneapolis.
Parola, A. C. (1990). “The stability of riprap used to protect bridge piers.” PhD thesis, Pennsylvania State University, University Park, Pa.
Parola, A. C. (1991). “The stability of riprap used to protect bridge piers.” Rep. No. FHWA-RD-91-063, Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Parola, A. C. (1993). “Stability of riprap at bridge piers.” Journal of Hydraulic Engineering, ASCE, 119(10), 1080–1093.
Parola, A. C. (1995). “Boundary stress and stability of riprap at bridge piers.” River, coastal and shoreline protection: Erosion control using riprap and armorstone, Thorne C. R. et al., eds., Wiley, New York.
Parola, A. C., Hagerty, D. J., and Kamojjala, S. (1998). “NCHRP 12- 39: Highway infrastructure damage caused by the 1993 Upper Mississippi River Basin flooding.” Transportation Research Board 1483, National Research Council, Washington, D.C.
Parola, A. C., Hagerty, D. J., Mueller, D. S., Melville, B. W., Parker, G., and Usher, J. S. (1996). “Scour at bridge foundations: Research needs.” NCHRP Project 24-8, Preliminary Draft Strategic Plan, National Co-operative Highway Research Program, Washington, D.C.
Parola, A. C., and Jones, J. S. (1989). “Sizing riprap to protect bridge piers from scour.” Transportation Research Record, 2(1290), 276–279.
Pilarczyk, K. W. (1995). “Simplified unification of stability formulae for revetment.” River, coastal and shoreline protection, Thorne C. R., Abt S. R., Barends F. B. J., Maynord S. T., and Pilarczyk K. W., eds., Wiley, New York.
Posey, C. J. (1974). “Tests of scour protection at bridge piers.” Journal of the Hydraulics Division, ASCE, 100(HY12), 1773–1783.
Quazi, M. E., and Peterson, A. W. (1973). “A method for bridge pier riprap design.” Proc., First Canadian Hydraulics Conference, 96–106.
Richardson, E. V., and Davis, S. R. (1995). “Evaluating scour at bridges.” Rep. No. FHWA-IP-90-017, Hydraulic Engineering Circular No. 18 (HEC-18), 3rd Ed., Office of Technology Applications, HTA-22, Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Richardson, E. V., Simons, D. B., and Julien, P. Y. (1988). Highways in the river environment. Federal Highway Administration, U.S. Department of Transportation, Washington, D.C.
Ruff, J. F., and Fotherby, L. M. (1995). “Bridge scour protection systems using toskanes.” Final Report, Project 91-02, Engineering Research Center, Colorado State University, Fort Collins, Colo.
Ruff, J. F., and Nickelson, J. R. (1993). “Riprap coverage around bridge piers.” Proc., National Hydraulic Engineering Conference, ASCE, New York, 1540–1545.
Schneible, D. E. (1951). “An investigation of the effect of bridge-pier shape on the relative depth of scour.” MS thesis, University of Iowa, Iowa City, Iowa.
Shen, H. W., Schneider, V. R., and Karaki, S. S. (1966). Mechanics of local scour, Institute for Applied Technology, National Bureau of Standards, U.S. Department of Commerce, Washington, D.C.
Simon, A. (1994). “Width adjustment: relative dominance in unstable alluvial streams.” Proc., ASCE National Hydraulics Conference, ASCE, New York, Cotroneo G. V. and Ramer R. R., eds., 974–978.
Simon, A. (1995). “Adjustment and recovery of unstable alluvial channels: Identification and approaches for engineering management.” Earth Surface Processes and Landforms, 20, 611–628.
Simons, D. B., Chen, Y. H., and Swenson, L. J. (1984). “Hydraulic test to develop design criteria for the use of Reno mattresses.” Report, Colorado State University, Fort Collins, Colo.
Simons, D. B., and Lewis, G. L. (1971). “Report—flood protection at bridge crossings.” Rep. No. CER71-72DBS-GL10, C.S.U. Civil Engineering Report, prepared for the Wyoming State Highway Department in conjunction with the U.S. Department of Transportation.
Simons, D. B., Li, R. M., and Associates (1989). “Sizing riprap for the protection of approach embankments and spur dykes and limiting the depth of scour at bridge piers and abutments.” Report No. FHWA-AZ-89-260, Vol. 1, Arizona Department of Transportation, Phoenix.
Singh, K. K., Verma, D. V. S., and Tiwari, N. K. (1995). “Scour protection at circular bridge piers.” Sixth International Symposium on River Sedimentation, New Delhi, India.
Sousa Pinto, N. L. de (1959). “Riprap protection against scour around bridge piers.” Master’s thesis, University of Iowa, Iowa City, Iowa.
Strom, H. G. (1962). River improvement and drainage in New Zealand and Australia. State Rivers and Water Supply Commission, Victoria, Australia.
Suzuki, K., Michiue, M., and Hinokidani, O. (1987). “Local bed form around a series of spur-dikes in alluvial channel.” Proc., 22nd. Congress, I.A.H.R., 316–321.
Tanaka, S., and Yano, M. (1967). “Local scour around a circular cylinder.” Proc., 12th. Congress, IAHR., Vol. 3, IAHR, Delft, The Netherlands, 193–201.
Thomas, Z. (1967). “An interesting hydraulic effect occurring at local scour.” Proc., 12th. Congress, IAHR, Vol. 3, IAHR, Delft, The Netherlands, 125–134.
Thorne, C. R., Abt, S. R., and Maynord, S. T. (1995). “Prediction of near-bank velocity and scour depth in meander bends for design of riprap revetments.” River, coastal and shoreline protection: Erosion control using riprap and armorstone, Thorne C. R., Abt S. R., Barends F. B. J., Maynord S. T., Pilarczyk K. W., Wiley, New York.
Ulrich, T. (1987). “Stability of rock protection on slopes.” Journal of Hydraulic Engineering, ASCE, 113(7), 879–891.
United Nations Economic Commission for Asia and the Far East (United Nations). (1953). “River training and bank protection.” Flood Control Series No. 4, Bangkok, Thailand.
University of Minnesota (1996). “Countermeasures to protect bridge piers from scour.” Second Interim Report, NCHRP Project No. 24-7, St. Anthony Falls Laboratory, University of Minnesota, Minneapolis.
University of Minnesota (1997). “Countermeasures to protect bridge piers from scour.” Quarterly Progress Report for period April 1997 to June 1997, NCHRP Project No. 24-7, St. Anthony Falls Laboratory, University of Minnesota, Minneapolis.
U.S. Army Corps of Engineers (USACE). (1984). Shore protection manual, Vol. II. U.S. Army Coastal Engineering Research Center, Vicksburg, Miss.
U.S. Department of Agriculture (USDA). (1996). “Chapter 16: Streambank and shoreline protection.” Natural Resources Conservation Service (NRCS) Engineering Field Handbook, U.S. Department of Agriculture, Washington, D.C.
Wang, T. W. (1994). “A study of pier scouring and scour reduction.” Proc., 9th Congress, Asia Pacific Division, IAHR, IAHR, Delft, The Netherlands, 18–28.
Worman, A. (1987). “Erosion mechanisms in a riprap protection around a pier.” Bulletin No. TRITA-VBI-I36, Hydraulics Laboratory, Royal Institute of Technology, Stockholm, Sweden.
Worman, A. (1989). “Riprap protection without filter layers.” Journal of Hydraulic Engineering, ASCE, 115(12), 1615–1630.
Information & Authors
Information
Published In
Sedimentation Engineering: Processes, Measurements, Modeling, and Practice
Pages: 543 - 577
Copyright
© 2008 American Society of Civil Engineers.
History
Published online: May 6, 2013
ASCE Technical Topics:
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.