Simplified Approaches to Design Medium-Rise Unbraced Steel Storage Pallet Racks. I: Elastic Buckling Analysis
Publication: Journal of Structural Engineering
Volume 141, Issue 11
Abstract
The design of steel storage pallet racks is quite complex, despite the fact that these structures are built with economical components and manufactured from thin coils or sheets. The most advanced approaches for rack design recommend the use of simplified methods to estimate the key parameters governing both static and seismic design. In the first case, which is the core of this first part of a two-part paper, an evaluation of the elastic critical load multiplier for the sway buckling mode () is required to select the method of analysis and check member instability. The term can be predicted through simplified approaches, which have been adequately calibrated for traditional steel structures constructed with members having a double-symmetric cross section. Rack uprights (columns) have, in general, an open cross section, with one axis of symmetry, and thus the overall frame response and member behavior is significantly influenced by Wagner’s coefficients, warping torsion, and shear-center eccentricity. Currently, these effects are neglected in routine rack design, owing to the absence of clear indications in standard provisions and the limited availability and knowledge of appropriate software tools supporting this complex design approach. This paper addresses the applicability of simplified approaches for the static design of medium-rise unbraced pallet racks, whereas the second part companion paper considers seismic approaches. A numerical analysis of several racks composed of different geometries, components, and degrees of stiffness of both beam-to-column and base-plate joints has been completed by using an open source finite-element analysis program for academic use, which is characterized by a refined beam formulation accounting for warping effects. Furthermore, the application to model racks of a traditional beam formulation on the basis of the coincidence between the shear center and the cross section centroid allows a direct appraisal of the warping influence on the prediction methods. Finally, to improve the accuracy of the critical load multiplier prediction, a suitable safety factor has been proposed to be used when beam formulations, including warping, are not available for structural analysis.
Get full access to this article
View all available purchase options and get full access to this article.
References
Australian Standards. (2012). “Steel storage racking.” AS 4084, Sydney, Australia.
Bajoria, K. M., Sangle, K. K., and Talicotti, R. S. (2010). “Modal analysis of cold-formed pallet rack structures with semi-rigid connections.” J. Constr. Steel Res., 66(3), 428–441.
Baldassino, N., and Bernuzzi, C. (2000). “Analysis and behaviour of steel storage pallet racks.” Thin Walled Struct., 37(4), 277–304.
Baldassino, N., and Zandonini, R. (2011). “Design by testing of industrial racks.” Adv. Steel Constr., 7(1), 27–47.
Bathe, K., and Wilson, E. L. (1976). Numerical methods in finite element analysis, Prentice-Hall, NJ.
Bathe, K. J., Wilson, E. L., and Iding, R. H. (1978). “NONSAP-finite element calculation for nonlinear static and dynamic analysis of complex structures.” Structural Engineering Laboratory, Univ. of California, Berkeley, CA.
Bernuzzi, C., and Gobetti, A. (2014). “An innovative finite element formulation for analysis of beam element with thin-walled mono-symmetric section.” Costruzioni Metalliche, ACAI, Milano, Italy.
Bernuzzi, C., Gobetti, A., Gabbianelli, G., and Simoncelli, M. (2015a). “Simplified approaches to design medium-rise unbraced steel storage pallet racks. II: Fundamental period estimates.” J. Struct. Eng., 04015037.
Bernuzzi, C., Gobetti, A., Gabbianelli, G., and Simoncelli, M. (2015b). “Unbraced pallet rack design in accordance with European practice—Part 2: Essential verification checks.” Thin Walled Struct., 86, 208–229.
Bernuzzi, C., Gobetti, A., Gabbianelli, G., and Simoncelli, M. (2014a). “Warping influence on the resistance of uprights in steel storage pallet racks.” J. Constr. Steel Res., 101, 224–241.
Bernuzzi, C., Pieri, A., and Squadrito, V. (2014b). “Warping influence on the static design of unbraced steel storage pallet racks.” Thin Walled Struct., 79, 71–82.
CEN (European Committee for Standardization). (2005a). “Eurocode 0: Basis of structural design.” EN 1990, Brussels, Belgium.
CEN (European Committee for Standardization). (2005b). “Eurocode 3: Design of steel structures—Part 1-1: General rules and rules for buildings.” EN 1993-1-1, Brussels, Belgium.
CEN (European Committee for Standardization). (2005c). “Eurocode 3: Design of steel structures—Part 1-8: Design of joints.” EN 1993-1-8, Brussels, Belgium.
CEN (European Committee for Standardization). (2009). “Steel static storage systems—Adjustable pallet racking systems—Principles for structural design.” EN 15512, Brussels, Belgium 137.
Chen, W. F., and Atsuta, T. (1977). Theory of beam-columns, Vol. 2: Space behaviour and design, Mc-Graw Hill, New York.
ConSteel Solutions. (2010). “Finite-element-program.” 〈http://www.consteel.hu〉 (May 8, 2014).
Dinis, P. B., Young, B., and Camotin, D. (2013). “Local-distortional interaction in cold-formed steel rack-section column.” Thin Walled Struct., 81, 185–194.
Filialtrault, A., Higgins, P. S., and Wanitkortkul, A. (2006). “Experimental stiffness and seismic response of pallet-type steel storage rack connectors.” Pract. Period. Struct. Des. Constr., 161–170.
Gilbert, B. P., and Rasmussen, K. J. R. (2012). “Drive-in steel storage racks. I: Stiffness test and 3D load transfer mechanisms.” J. Struct. Eng., 135–147.
Godley, M. H. R. (1991). “Storage racking.” Chapter 11, Design of cold formed steel members, Rhodes, ed., Elsevier Applied Science, London, 361–398.
Hibbit, Karlsson and Sorensen. (2006). Abaqus 6.8 user’s manual, Providence, RI.
Horne, M. R. (1975). “An approximate method for calculating the elastic critical loads of multi-storey plane frame.” Struct. Eng., 53(6), 242–248.
Hsiao, K. M., and Lin, W. Y. (2000). “A co-rotational formulation for thin-walled beams with mono-symmetric open sections.” Comput. Meth. Appl. Mech. Eng., 190(8), 1163–1185.
Hughes, T. J. R. (1987). The finite element methods, Prentice-Hall, NJ.
LS-DYNA [Computer software]. Livermore, CA, Livermore Software Technology Corporation.
McGuire, W. (1992). “Computer-aided analysis.” Constructional steel design—An international guide, P. J. Dowling, J. E. Harding, and R. Bjorhovde, eds., Elsevier Applied Science, New York, 915–931.
RMI (Rack Manufacturers Institute). (2012). “Specification for the design, testing and utilization of industrial steel storage racks.”, Charlotte, NC, 59.
Sangle, K. K., Bajoria, K. M., and Talicotti, R. S. (2012). “Elastic stability analysis of cold-formed pallet rack structures with semi-rigid connections.” J. Constr. Steel Res., 71, 245–262.
Shafer, B. W. (2011). “Cold-formed steel structures around the world—A review of recent advances in applications, analysis and design.” Steel Constr., 4(3), 141–149.
SOFiSTiK. (2013). “The SOFiSTiK FEM packages.” 〈http://www.sofistik.com/en/〉 (Dec. 1, 2013).
Teh, L. H., and Clarke, M. J. (1998). “Co-rotational and Lagrangian formulations for elastic three-dimensional beam finite elements.” J. Constr. Steel Res., 48(2–3), 123–144.
Teh, L. H., Hancock, G. J., and Clarke, M. J. (2004). “Analysis and design of double sided high-rise steel pallet rack frames.” J. Struct. Eng., 1011–1021.
Timoshenko, S. P., and Gere, J. M. (1961). Theory of elastic stability, 2nd Ed., McGraw Hill, New York.
Turkalj, G., Brnic, J., and Prpic-Orsic, J. (2003). “Large rotation analysis of elastic thin-walled beam-type structures using ESA approach.” Comput. Struct., 81(18–19), 1851–1864.
Vlasov, V. Z. (1961). Thin walled elastic beams, 2nd Ed., Israel Program for Scientific Transactions, Jerusalem, Israel.
Werkle, H. (2008). Finite element in der Baustatik, Vieweg, Braunschweig-Wiesbaden, Germany.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 141 • Issue 11 • November 2015
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Feb 22, 2014
Accepted: Jan 7, 2015
Published online: Mar 5, 2015
Discussion open until: Aug 5, 2015
Published in print: Nov 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.