Practical Application of Digital Image Processing in Measuring Concrete Crack Widths in Field Studies
Publication: Practice Periodical on Structural Design and Construction
Volume 28, Issue 1
Abstract
Cracking in concrete structures is a ubiquitous problem and affects the serviceability of such structures. In many cases, it is imperative to properly measure and monitor a crack’s size to identify locations for repair and rehabilitation. This paper describes two field studies that used digital image processing to measure the width of cracks in concrete structures. The first field study compared crack measurements from digital image processing, a handheld microscope, and a crack gauge card. In the second field study, digital image processing was used to measure end region cracks in precast pretensioned concrete girders. Guidance is provided for engineers who wish to use digital image processing in field studies. Conditions where digital image processing may lead to errors are identified, and limitations of the methods are discussed. In general, the studies demonstrate that image processing methods can efficiently measure the size of cracks in concrete structures in field settings and that image-based measurements are comparable to microscope measurements.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, and code generated or used during the study are available from the corresponding author by request. The available data are crack images, ImageJ data, and spreadsheets.
Acknowledgments
The authors wish to thank the Wisconsin DOT (WisDOT) and USDOT for providing the funding for this research. County Materials Corp. of Janesville, Wisconsin, provided the access for the girder field study. Mr. Matt Mueller and Dr. Todd Davis conducted the site visits and data collection for the girder field study. This research was associated with a project funded through WisDOT and the USDOT. Neither WisDOT nor USDOT assumes any liability for the contents or the use of this research, nor does this presentation reflect official views, policies, standard specifications, or regulations of either department.
References
Abdel-Qader, I., O. Abudayyeh, and M. E. Kelly. 2003. “Analysis of edge-detection techniques for crack identification in bridges.” J. Comput. Civ. Eng. 17 (4): 255–263. https://doi.org/10.1061/(ASCE)0887-3801(2003)17:4(255).
Albareda-Valls, A., A. Bustos Herrera, J. L. Zamora Mestre, and S. S. Zaribaf. 2018. “Image post-processing method for quantification of cracking in RC precast beams under bending.” Buildings 8 (11): 158. https://doi.org/10.3390/buildings8110158.
Alipour, M., S. J. Washlesky, and D. K. Harris. 2019. “Field deployment and laboratory evaluation of 2D digital image correlation for deflection sensing in complex environments.” J. Bridge Eng. 24 (4): 04019010. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001363.
Aydilek, A. H., S. H. Oguz, and T. B. Edil. 2002. “Digital image analysis to determine pore opening size distribution of nonwoven geotextiles.” J. Comput. Civ. Eng. 16 (4): 280–290. https://doi.org/10.1061/(ASCE)0887-3801(2002)16:4(280).
Barkavi, T., and C. Natarajan. 2019. “Processing digital image for measurement of crack dimensions in concrete.” Civ. Eng. Infrastruct. J. 52 (1): 11–22. https://doi.org/10.22059/ceij.2019.246397.1444.
Chen, P., Y. Chang, L. Chang, and P. C. Doerschuk. 2002. “Application of multi-resolution pattern classification to steel bridge coating assessment.” J. Comput. Civ. Eng. 16 (4): 244–251. https://doi.org/10.1061/(ASCE)0887-3801(2002)16:4(244).
Dizaji, M. S., D. K. Harris, B. Kassner, and J. C. Hill. 2021. “Full-field non-destructive image-based diagnostics of a structure using 3D digital image correlation and laser scanner techniques.” J. Civ. Struct. Health Monit. 11 (5): 1415–1428. https://doi.org/10.1007/s13349-021-00516-6.
Firdousi, R., and S. Parveen. 2014. “Local thresholding techniques in image binarization.” Int. J. Eng. Comput. Sci. 3 (3): 14.
Gamble, W. 2014. “Discussion of comparison of details for controlling end-region cracks in pre-tensioned concrete I-Girders.” PCI J. 59 (Jan): 134–136.
Garboczi, E. J. 2002. “Three-dimensional mathematical analysis of particle shape using X-ray tomography and spherical harmonics: Application to aggregates used in concrete.” Cem. Concr. Compos. 32 (10): 1621–1638.
Gergely, P., M. A. Sozen, and C. P. Siess. 1963. The effect of reinforcement on anchorage zone cracks in prestressed concrete members. Urbana, IL: Univ. of Illinois.
Gonzalez, R. C., and R. E. Woods. 2017. Digital image processing. 4th ed. Austin, TX: Pearson, Inc.
Hasenkamp, C. J., S. S. Badie, C. Y. Tuan, and M. K. Tadros. 2008. “Sources of end zone cracking of pretensioned concrete girders.” In Civil Engineering Faculty Proc.& Presentations. Omaha, NE: Univ. of Nebraska.
Hoang, N. D. 2018. “Detection of surface crack in building structures using image processing technique with an improved OTSU method for image thresholding.” Adv. Civ. Eng. 2018 (1): 3924120. https://doi.org/10.1155/2018/3924120.
Koller, D., K. Daniilidis, and H. H. Nagel. 1993. “Model-based object tracking in monocular image sequences of road traffic scenes.” Int. J. Comput. Vision 10 (3): 257–281.
Lanzón, M., V. Cnudde, T. Kock, and J. Dewanckele. 2012. “X-ray microtomography (-CT) to evaluate microstructure of mortars containing low density additions.” Cem. Concr. Compos. 34 (9): 993–1000. https://doi.org/10.1016/j.cemconcomp.2012.06.011.
Lee, Y., and S. Maharjan. 2019. “End-region cracking in prestressed concrete girders and its solution.” J. Civ. Constr. Eng. 5 (3): 15–27. https://doi.org/10.5281/zenodo.3386658.
Lin, D. F., H. Y. Wang, and H. L. Luo. 2004. “Assessment of fire-damaged mortar using digital image process.” J. Mater. Civ. Eng. 16 (4): 383–386. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:4(383).
Liu, Y., S. Cho, B. F. Spencer, and J. Fan. 2014. “Automated assessment of cracks on concrete surfaces using adaptive digital image processing.” Smart Struct. Syst. 14 (4): 719–741. https://doi.org/10.12989/sss.2014.14.4.719.
Liu, Y., C. Soojin, B. F. Spencer, and J. Fan. 2016. “Concrete crack assessment using digital image processing and 3D scene reconstruction.” J. Comput. Civ. Eng. 30 (1): 04014124. https://doi.org/10.1061/(ASCE)CP.1943-5487.0000446.
Marshall, W., and A. Mattock. 1962. “Control of horizontal cracking in the ends of pretensioned prestressed concrete girders.” PCI J. 7 (Jan): 74. https://doi.org/10.15554/pcij.10011962.56.74.
Murphy, A., S. Sreedhara, A. Poursaee, and B. Ross. 2021. “Comparison of flexural cracking in reinforced concrete beams with different rebar coatings.” In Proc., PCI National Conf. New Orleans, LA: Prestressed Concrete Institute.
Murray, C. D., B. N. Cranor, R. W. Floyd, and J. S. Pei. 2019. “Experimental testing of older AASHTO Type-II bridge girders with corrosion damage at the ends.” PCI J. 64 (1): 1–3. https://doi.org/10.15554/pcij64.1-02.
Oliva, M. G., and P. Okumus. 2011. Finite element analysis of deep wide-flanged pre-stressed girders to understand and control end cracking. Wisconsin: Wisconsin Highway Research Program - WisDOT.
Otsu, N. 1979. “A threshold selection method from gray-level histograms.” IEEE Trans. Syst. Man. Cyber. 9 (1): 62–66. https://doi.org/10.1109/TSMC.1979.4310076.
Peng, Y., M. M. A. Liping Ying, and Y. Wang. 2021. “Mesoscale fracture analysis of recycled aggregate concrete based on digital image processing technique.” Struct. Concr. 22 (Sep): 33–47. https://doi.org/10.1002/suco.201900338.
Pitas, I. 2000. Digital image processing algorithms and applications. 1st ed. New York: Wiley.
Rahman, M. D., I. Saifullah, and S. Ghosh. 2019. “Detection and measurements of cracks in axially loaded tension RC members by image processing technique.” Am. J. Civ. Eng. Archit. 7 (2): 115–120. https://doi.org/10.12691/ajcea-7-2-5.
Ramos, T., S. E. André Furtado, H. R. Sofia Alves, P. J. António Arêde, and P. M. Moreira. 2015. “2D and 3D digital image correlation in civil engineering—Measurements in a masonry wall.” In Proc., 1st Int. Conf. on Structural Integrity Funchal, 215–222. Portugal: Procedia Engineering.
Razmjoo, A., and A. Poursaee. 2013. “Quantitative CT-scan imaging approach in determining the air voids and aggregate content in concrete.” J. Civ. Eng. 4 (1): 12–19.
Razmjoo, A., and A. Poursaee. 2016. “Finite element modeling of chloride diffusion in concrete using image processing for characterizing real shape and distribution of different phases.” Adv. Civ. Eng. Mater. 5 (1): 20150032. https://doi.org/10.1520/ACEM20150032.
Ronanki, V. S., D. I. Burkhalter, S. Aaleti, W. Song, and J. A. Richardson. 2017. “Experimental and analytical investigation of end zone cracking in BT-78 girders.” Eng. Struct. 151 (5): 503–517. https://doi.org/10.1016/j.engstruct.2017.08.014.
Ross, B., A. Poursaee, S. Sreedhara, M. Mueller. 2021. Textured-epoxy Coated and Galvanized Reinforcement to Reduce Cracking in Concrete Bridge Decks and Components. Madison, WI: Wisconsin DOT.
Ross, B. E., M. D. Willis, H. R. Hamilton, and G. R. Consolazio. 2014. “Comparison of details for controlling end-region cracks in precast, pretensioned concrete I-girders.” PCI J. 59 (2): 96–108. https://doi.org/10.15554/pcij.03012014.96.108.
Ruan, T., and A. Poursaee. 2019. “Fiber-distribution assessment in steel fiber-reinforced UHPC using conventional imaging, X-ray CT scan, and concrete electrical conductivity.” J. Mater. Civ. Eng. 31 (8): 04019133. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002733.
Schneider, C. A., W. S. Rasband, and K. W. Eliceiri. 2012. “NIH Image to ImageJ: 25 years of image analysis.” Nat. Methods 9 (7): 671–675. https://doi.org/10.1038/nmeth.2089.
Shih, F. Y. 2009. Image processing and mathematical morphology: Fundamentals and applications. London: CRC Press.
Singh, O. I., T. Sinam, O. James, and T. R. Singh. 2012. “Local contrast and mean based thresholding technique in image binarization.” Int. J. Comput. Appl. Technol. 51 (6): 4–10. https://doi.org/10.5120/8044-1362.
Singh, T. R., S. Roy, O. I. Singh, T. Sinam, and K. M. Singh. 2011. “A new local adaptive thresholding technique in binarization.” Int. J. Comput. Sci. Issues 8 (6): 2.
Valença, J., D. Dias-da-Costa, and E. Júlio. 2012. “Characterisation of concrete cracking during laboratorial tests using image processing.” Constr. Build. Mater. 28 (4): 607–615. https://doi.org/10.1016/j.conbuildmat.2011.08.082.
Willis, M. D. 2014. Post-tensioning to prevent end-region cracks in pretensioned concrete girders. Clemson, SC: Clemson Univ.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Jan 26, 2022
Accepted: Jul 1, 2022
Published online: Oct 7, 2022
Published in print: Feb 1, 2023
Discussion open until: Mar 7, 2023
ASCE Technical Topics:
- Architectural engineering
- Building management
- Comparative studies
- Computer vision and image processing
- Concrete
- Concrete structures
- Continuum mechanics
- Cracking
- Engineering fundamentals
- Engineering materials (by type)
- Engineering mechanics
- Field tests
- Fracture mechanics
- Materials engineering
- Methodology (by type)
- Precast concrete
- Research methods (by type)
- Serviceability
- Solid mechanics
- Structural engineering
- Structures (by type)
- Tests (by type)
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.