Side Shear Setup. I: Test Piles Driven in Florida
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 131, Issue 3
Abstract
The available literature indicates that pile side shear increases almost linearly with the logarithm of time elapsed after driving, sometimes described using a dimensionless setup factor. A test pile program conducted by the University of Florida measured side shear setup (SSS) for up to 4.7 years on five, , square, prestressed, concrete piles driven into coastal plain soils at different sites. Dynamic tests performed during initial driving and two restrikes measured short-term SSS. Osterberg cells, the first installed in driven concrete piles, measured long-term SSS starting within of driving and continuing with two to five additional, staged tests. Extensive instrumentation, including vibrating wire strain gauges, Marchetti total stress cells, and vibrating wire piezometers, divided the five piles into 28 segments by soil type with horizontal effective stress measurements for 18 of the segments. This paper describes the University of Florida test pile program and its results. A companion paper analyzes the test results and recommends procedures for implementing SSS in design.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The National Science Foundation provided primary funding for this project with substantial assistance from the FDOT, the FHWA, and Schmertmann and Crapps, Inc. FDOT Districts 1, 2, 3, and 5 provided valuable assistance in arranging the installation of the test piles in conjunction with on-going bridge projects, and field testing support for the site investigations. The following FDOT Engineers helped facilitate this research: Mr. William Knight, Dr. Sastry Putcha, Mr. Chandra Samakur, Mr. Jon Foshee, Mr. Tom Malerk, Dr. Ching Kuo, Ms. Terry Puckett, and Mr. Peter Lai.
References
Airhart, T. P., Hirsch, T. J., and Coyle, H. M. (1967). “Pile-soil system response in clay as a function of excess pore water pressure and other soil properties.” Research Rep. No. 33-8. Texas Transportation Institute, Texas A&M Univ., College Station, Tex.
American Society for Testing and Materials. (2000). “Standard test method for piles under static axial compressive load.” D 1143-81, Annual Book of ASTM Standards. ASTM, Philadelphia, 4:08, 96–106.
Axelsson, G. (1998a). “Long-term setup of driven piles in noncohesive.” Licentiate thesis, Dept. of Civil and Environmental Engineering, Royal Institute of Technology, Stockholm, Sweden.
Axelsson, G. (1998b). “Long-term setup of driven piles in noncohesive soils evaluated from dynamic tests on penetration rods.” Proc., 1st Int. Conf. on Site Characterization, P. K. Robertson and P. W. Mayne, eds., Balkema, Brookfield, Vt., 2, 895–900.
Azzouz, A. S., and Morrison, J. M. (1988). “Field measurements on model pile in two clay deposits.” J. Geotech. Eng., 114(1), 104–121.
Bond, A. J., and Jardine, R. J. (1991). “Effects of installing displacement piles in a high OCR clay.” Geotechnique, 41(3), 341–363.
Bullock, P. J. (1999). “Pile friction freeze: A field and laboratory study.” PhD dissertation, Dept. of Civil Engineering, Univ. of Florida, Gainesville, Fla.
Bullock, P. J., Schmertmann, J. H., McVay, M. C., and Townsend, F. C. (2005). “Side shear setup. II Results from Florida test piles.” J. Geotech. Geoenviron. Eng., 131(3), 301–310.
Camp, W. M., Wright, W. B., and Hussein, M. (1993). “The effect of overburden on pile capacity in a calcareous marl.” Proc., 18th Annual Members’ Conf., Deep Foundations Institute, Englewood Cliffs, N.J.
Chow, F. C., Jardine, R. J., Brucy, F., and Nauroy, J. F. (1996). “The effects of time on the capacity of pipe piles in dense marine sand.” Proc., 28th Annual Offshore Technology Conf., Offshore Technology Conference, Houston, Tex.
Chow, F. C., Jardine, R. J., Brucy, F., and Nauroy, J. F. (1998). “Effects of time on capacity of pipe piles in dense marine sand.” J. Geotech. Geoenviron. Eng., 124(3), 254–264.
Fellenius, B. H., Riker, R. E., O’Brien, A. J. O., and Tracy, G. R. (1989). “Dynamic and static testing in soil exhibiting set-up.” J. Geotech. Eng., 115(7), 984–1001.
Karlsrud, K., and Haugen, T. (1985). “Axial static capacity of steel model piles in overconsolidated clays.” Proc., 11th Int. Conf. on Soil Mechanics and Foundation Engineering, Balkema, Brookfield, Vt., 3, 1401–1406.
Kehoe, S. P. (1989). “An analysis of time effects on the bearing capacity of driven piles.” Master’s Rep. Dept. of Civil Engineering, Univ. of Florida, Gainesville, Fla.
Lutenegger, A. J., and Miller, G. A. (1993). “Evaluation of dilatometer method to determine axial capacity of driven model pipe piles in clay.” Proc., Design and Performance of Deep Foundations: Piles and Piers in Soil and Soft Rock. ASCE, Reston, Va., 41–63.
Marchetti, S., Totani, G., Campanella, R. G., Robertson, P. K., and Taddei, B. (1986). “The DMT- method for piles driven in clay.” Proc., Use of In Situ Tests in Geotechnical Engineering, Clemence, ASCE, Reston, Va., 765–779.
McRae, J. B., and Simmonds, T. (1991). “Long-term stability of vibrating wire instruments: One manufacturer's perspective.” Proc., 3rd Int. Symposium on Field Measurements in Geomechanics. G. Sørum, ed., Balkema, Brookfield, Vt., 283–293.
McVay, M. C., Schmertmann, J., Townsend, F., and Bullock, P. (1999). “Pile friction freeze: A field and laboratory study.” Research Rep. No. WPI 0510632, Florida Department of Transportation, Tallahassee, Fla.
Ng, E. S., Tsang, S. K., and Auld, B. C. (1988). “Pile foundations: The behavior of piles in cohesionless soils.” Report No. FHWA-RD-88-081, Federal Highway Administration, McLean, Va.
Preim, M. J., March, R., and Hussein, M. (1989). “Bearing capacity of piles in soils with time dependent characteristics.” Proc., 3rd Int. Conf. on Piling and Deep Foundations, J. B. Burland and J. M. Mitchell, eds., Balkema, Brookfield, Vt., 363–370.
Samson, L., and Authier, J. (1986). “Change in pile capacity with time: Case histories.” Can. Geotech. J., 23(2), 174–180.
Schmertmann, J. H. (1991). “The mechanical aging of soils.” J. Geotech. Eng., 117(9), 1285–1330.
Seidel, J. P., Haustorfer, I. J., and Plesiotis, S. (1988). “Comparison of static and dynamic testing for piles founded into limestone.” Proc., 3rd Int. Conf. on the Application of Stress-Wave Theory to Piles, B. G. Fellenius, ed., BiTech Publishers, Vancouver, BC, 717–723.
Shioi, Y., Yoshida, O., Meta, T., and Homma, M. (1992). “Estimation of bearing capacity of steel pipe pile by static loading test and stress-wave theory.” Proc., 4th Int. Conf. on the Application of Stress-Wave Theory to Piles, F. B. S. Barends, ed., Balkema, Brookfield, Vt., 325–330.
Skov, R., and Denver, H. (1988). “Time-dependence of bearing capacity of piles.” Proc., 3rd Int. Conf. on the Application of Stress-Wave Theory to Piles, B. G. Fellenius, ed., BiTech Publishers, Vancouver, BC, 879–888.
Svinkin, M. R., Morgano, C. M., and Morvant, M. (1994). “Pile capacity as a function of time on clayey and sandy soils.” Proc., 5th Int. Conf. on Piling and Deep Foundations, Deep Foundations Institute, Englewood Cliffs, N.J., 1.11.1–1.11.8.
Tavenas, F., and Audy, R. (1972). “Limitations of the driving formulas for predicting the bearing capacities of files in sand.” Can. Geotech. J., 9(1), 47–62.
Information & Authors
Information
Published In
Copyright
© 2004 ASCE.
History
Received: Aug 11, 2003
Accepted: Jun 26, 2004
Published online: Mar 1, 2005
Published in print: Mar 2005
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.