Design of Sag Vertical Curves in Three-Dimensional Alignments
Publication: Journal of Transportation Engineering
Volume 124, Issue 1
Abstract
Headlight sight distance has been an important element in designing sag vertical curves because nighttime drivers need sufficient sight distance for stopping, and also because they depend on the road marking to maintain uniform speed and proper lane positioning. Considering an isolated sag vertical curve in a two-dimensional projection based on the sight distance needs for stopping, the current design standards recommend a minimum length of the sag curve. However, little research work has been directed toward determining the available headlight sight distance in three-dimensional highway alignments. A new analytical model developed by the writers for 3D analysis of headlight sight distance has shown that the 2D analysis may overestimate the available headlight sight distance on sag vertical curves combined with horizontal curves. In this paper, a computer program based on the 3D analytical model is used to evaluate the current 2D standards for sag vertical curves on fill sections. The results show that the current 2D design standards overestimate the available headlight sight distance and therefore underestimate the required length of sag vertical curves combined with horizontal curves. In this paper more accurate values for the required length of sag vertical curves combined with horizontal circular curves are developed. A more economical design is also suggested through the use of asymmetrical (compound) sag vertical curves.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Easa, S. M.(1991). “Sight distance model for unsymmetrical sag curves.”Transp. Res. Rec., 1303, 51–62.
2.
Easa, S. M.(1994a). “Design considerations for highway reverse curves.”Transp. Res. Rec., 1445, 1–11.
3.
Easa, S. M.(1994b). “New and improved unsymmetrical vertical curve for highways.”Transp. Res. Rec., 1445, 94–100.
4.
Easa, S. M., and Hassan, Y. (1997). “Analysis of headlight sight distance on separate horizontal and vertical alignments.”Can. J. Civ. Engrg.
5.
Hassan, Y. (1996). “Geometric design considerations of combined horizontal and vertical highway alignments,” PhD thesis, Carleton Univ., Ottawa, Canada.
6.
Hassan Y., Easa, and S. M., and Abd El Halim(1996a). “Analytical model for sight distance analysis on 3-D highway alignments.”Transp. Res. Rec., 1523, 1–10.
7.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O. (1996b). “Computer model for establishing no-passing zones on 3-D highway alignments.”Proc., 1st Transp. Spec. Conf., S. Easa, ed., Can. Soc. for Civ. Engrg., Montreal, Quebec, Canada, IIIb, 411–422.
8.
Hassan, Y., Abd El Halim, A. O., and Easa, S. M.(1997a). “Application for automated marking on two-lane highways: Case study.”Can. J. Civ. Engrg., 24(2), 276–287.
9.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O.(1997b). “Automation of marking passing and no-passing zones on two-lane highways.”Can. J. Civ. Engrg., 24(2), 263–275.
10.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O.(1997c). “Design considerations for combined highway alignments.”J. Transp. Engrg., ASCE, 123(1), 60–68.
11.
Hassan, Y., Easa, S. M., and Abd El Halim, A. O. (1997d). “Modelling headlight sight distance on 3-D highway alignments.”Transp. Res. Rec. 1579, 79–88.
12.
Krammes, R. A., and Garnham, M. A. (1995). “Review of alignment design policies worldwide.”Symp. on Hwy. Geometric Des. Practices, Transp. Res. Board, Washington, D.C.
13.
Manual of geometric design standards for Canadian roads. (1986). Transp. Assn. of Canada (TAC), Ottawa, Canada.
14.
A policy on geometric design of highways and streets. (1994). American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
15.
Rockwell, T. H., Ernst, R. L., and Rulon, M. J. (1970). “Visual requirements in night driving,”Rep. 99, National Cooperative Highway Research Program.
16.
Smith, B. L., and Lamm, R.(1994). “Coordination of horizontal and vertical alignment with regard to highway esthetics.”Trans. Res. Rec., 1445, 73–85.
Information & Authors
Information
Published In
Journal of Transportation Engineering
Volume 124 • Issue 1 • January 1998
Pages: 52 - 58
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Jan 1, 1998
Published in print: Jan 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.