Reliability of Light-Frame Wall Systems Subject to Combined Axial and Transverse Loads
Publication: Journal of Structural Engineering
Volume 131, Issue 9
Abstract
Wood frame walls are essential subassemblies used to transmit roof, floor, wind, and seismic loads into lower stories and eventually into the foundation of light-frame structures. There has been some discussion and debate in recent years over appropriate system factors for use in the design of repetitive wall members, which typically are much smaller in the cross section than floor joists. In addition to having greater flexibility than floors, wood stud walls also may be subject to the actions of combined loads, and their load-sharing behavior may be significantly influenced by the presence of openings. As a precursor to evaluating system factors for design, this study investigated load-sharing and system effects in light-frame walls subject to combined axial and transverse loads. An analytical model was developed to account for partial composite action, load-sharing, two-way action, and openings in the wall system. The model consisted of two main components: A system model and a member model. The system model was a beam-spring analog model with spring stiffnesses obtained from the member model. The member model was a beam-column model which took into account partial composite action between the stud and the sheathing and possible end restraints. After validating the model using experimental test data from other studies, it was incorporated into a Monte Carlo simulation to evaluate the strength and reliability of light-frame wall systems subject to combined axial and transverse loads. Sensitivity studies were performed to investigate how system parameters affected the wall system strength and reliability. Critical load combinations were determined external to the reliability analysis. Reliabilities were then evaluated using a portfolio of representative light-frame wall systems designed according to current code provisions.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers are grateful for the support provided by the USDA NRI Competitive Grants Program through Grant No. 99-35103-8543. The findings and opinions reported here are those of the writers and do not reflect those of the sponsoring agency.
References
Amana, E. J., and Booth, L. G. (1967). “Theoretical and experimental studies on nailed and glued plywood stressed-skin components: Part I. Theoretical study.” J. Inst. Wood Sci., 4(1), 43–69.
American Forest and Paper Association (AF&PA). (1996). Load and resistance factor design (LRFD) manual for engineered wood construction, American Forest and Paper Association, Washington, D.C.
American Forest and Paper Association (AF&PA). (1997). National design specification (NDS) for wood construction, American Forest and Paper Association, Washington, D.C.
ASTM (1999). “Practice for establishing allowable properties for visually graded dimension lumber from in-grade tests of full-size specimens.” ASTM Standards D1990-97, Philadelphia.
Bulleit, W. M. (1985). “Relative reliability of dimension lumber in bending.” J. Struct. Eng., 111(9), 1948–1963.
Bulleit, W. M. (1987). “Markov model for wood structural systems.” J. Struct. Eng., 113(9), 2023–2031.
Bulleit, W. M., and Liu, W. F. (1995). “First-order reliability analysis of wood structural systems.” J. Struct. Eng., 121(3), 517–529.
Bulleit, W. M., and Rosowsky, D. V. (1998). “Reliability analysis of light-frame wall systems.” Proc., Structural Engineers World Congress SEWC’98, San Francisco.
Cramer, S. M., and Wolfe, R. E. (1989). “Load-distribution model for light-frame wood roof assemblies.” J. Struct. Eng., 115(10), 2603–2616.
DeBonis, A. L. (1980). “Stochastic simulation of wood load-sharing systems.” J. Struct. Div. ASCE, 106(2), 393–410.
Ellingwood, B., Galambos, T. V., MacGregor, J. G., and Cornell, C. A. (1980). “Development of a probability based load criterion for American National Standard A58.” National Bureau of Standards, Special Publication SP No. 577, Washington, D.C.
Foschi, R. O. (1982). “Structural analysis of wood floor systems.” J. Struct. Div. ASCE, 108(7), 1557–1574.
Foschi, R. O. (1984). “Reliability of wood structural systems.” J. Struct. Div. ASCE, 110(12), 2995–3015.
Folz, B., and Foschi, R. O. (1989). “Reliability-based design of wood structural systems.” J. Struct. Eng., 115(7), 1660–1680.
Galambos, T. V., Ellingwood, B., MacGregor, J. G., and Cornell, C. A. (1982). “Probability-based load criteria: Assessment of current design practice.” J. Struct. Div. ASCE, 108(5), 959–977.
Goodman, J. R., Vanderbilt, M. D., Criswell, M. E., and Bodig, J. (1974). “Composite and two-way action in wood joist floor systems.” Wood Sci., 7(1), 25–33.
Green, D. G., and Evans, J. W. (1987). Mechanical properties of visually graded lumbers, Vols. 1–4, Forest Service, Forest Products Laboratory, U.S. Department of Agriculture, Madison, Wis.
Gromala, D. S. (1983). “Light-frame wall systems: Performance and predictability,” U.S. Dept. of Agriculture, Forest Service, Forest Products Laboratory, Research Paper FPL 442, Madison, Wis.
Gromala, D. S., and Polensek, A. (1983). “Analysis and design of wall systems under axial and bending loads.” Wall and floor systems: Design and performance of light-frame structures, Forest Products Research Society, Madison, Wis., 87–106.
Hendrickson, E. M., Ellingwood, B., and Murphy, J. (1987). “Limit state probabilities for wood structural members.” J. Struct. Eng., 113(1), 88–106.
Kasal, B., and Leichti, R. J. (1992). “Nonlinear finite-element model for light-frame stud walls.” J. Struct. Eng., 118(11), 3122–3135.
Liu, W. F., and Bulleit, W. M. (1995a). “Approximate reliability analysis of wood structural systems.” Struct. Safety, 17, 59–78.
Liu, W. F., and Bulleit, W. M. (1995b). “Overload behavior of sheathed lumber systems.” J. Struct. Eng., 121(7), 1110–1118.
McCutcheon, W. J. (1977). “Method for predicting the stiffness of wood-joist floor systems with partial composite action.” Research Paper FPL 289, U.S. Dept. of Agriculture, Forest Service, Forest Products Laboratory, Madison, Wis.
McCutcheon, W. J. (1984). “Deflections of uniformly loaded floors: A beam-spring analog.” Research Paper FPL 449, USDA Forest Service, Forest Products Laboratory, Madison, Wis.
McCutcheon, W. J. (1986). “Stiffness of framing members with partial composite action.” J. Struct. Eng., 112(7), 1623–1637.
Melchers, R. E. (1999). Structural reliability: Analysis and prediction, Wiley, Chichester, England.
Mtenga, P. V., Cramer, S. M., Peyrot, A. H., and Wolfe, R. E. (1995). “System factors for light-frame wood truss assemblies.” J. Struct. Eng., 121(2), 290–300.
O’Rourke, M., Redfield, R., and Von Bradsky, P. (1982). “Uniform snow loads on structures.” J. Struct. Div. ASCE, 108(12), 2781–2798.
Philpot, T. A., and Rosowsky, D. V. (1992). “Statistics for light-occupancy live load modeling.” Structural Engineering Rep. No. CE-STR-92-3, Purdue Univ., West Lafayette, Ind.
Philpot, T. A., Fridley, K. J., and Rosowsky, D. V. (1994). “Structural reliability analysis method for viscoelastic members.” Comput. Struct., 53(3), 591–599.
Philpot, T. A., Rosowsky, D. V., and Fridley, K. J. (1995). “Reliability of wood joist floor systems with creep.” J. Struct. Eng., 121(6), 946–954.
Polensek, A. (1972). “Static and dynamic analysis of wood-joist floors by the finite element method.” PhD thesis, Oregon State Univ. Corvallis, Or.
Polensek, A. (1975a). “Rational design procedure for wood-stud walls under bending and compression loads.” Paper No. 1027, Forest Research Laboratory, Oregon State Univ., Corvallis, Or.
Polensek, A. (1975b). “Finite element analysis for wood-stud walls under bending and compression loads.” Limited Distribution Report, Forest Research Laboratory, Oregon State Univ., Corvallis, Or.
Polensek, A. (1976a). “Finite element analysis of wood-stud wall.” J. Struct. Div. ASCE, 102(7), 1317–1335.
Polensek, A. (1976b). “Nonlinear behavior of nailed wood-stud walls at service loads and overloads.” Proc., 2nd Int. Conf. on Mechanical Behavior of Materials, 1948–1952, Boston.
Polensek, A. (1982). “Effect of construction variables on performance of wood-stud walls.” For. Prod. J., 32(5), 37–41.
Polensek, A., and Kazic, M. (1991). “Reliability of nonlinear wood composites in bending.” J. Struct. Eng., 117(6), 1685–1702.
Rosowsky, D. V., and Ellingwood, B. (1990). “Stochastic damage accumulation and probabilistic codified design for wood.” Civil Engineering Report No. 1990-02-02, Johns Hopkins Univ., Baltimore.
Rosowsky, D. V., and Ellingwood, B. (1991). “System reliability and load-sharing effects in light-frame wood construction.” J. Struct. Eng., 117(4), 1096–1114.
Rosowsky, D. V., and Huang, Z. (2000). “Wind load statistics for reliability analysis of light-frame roof components in hurricane-prone regions.” Proc., 9th ASCE Specialty Conf. on Probabilistic Mechanics and Structural Reliability, ASCE, N. Y. (CD ROM).
Rosowsky, D. V., Bulleit, W. M., Yu, G., and Wei, C. P. (2001). “System reliability analytical model for stud walls subject to combined loads.” Proc., Int. Conf. Structural Safety and Reliability, ICOSSAR’01.
Srikanth, T. S. (1992). “Structural reliability of light-frame wood systems with composite action and load sharing.” PhD thesis, Oregon State Univ., Corvallis, Or.
Stefanescu, M., et al. (2000). “Testing of wood walls under combined vertical and out of plane (transverse) loading, and validation of the analysis program PANEL.” Dept. of Civil Engineering and Dept. of Wood Science, Univ. of British Columbia, Vancouver, B.C., Canada, and Dept. of Civil Engineering, Clemson Univ., Clemson, S.C.
Thompson, E. G., Goodman, J. R., and Vanderbilt, M. D. (1975). “Finite element analysis of layered wood systems.” J. Struct. Div. ASCE, 101(12), 2659–2672.
Thompson, E. G., Vanderbilt, M. D., and Goodman, J. R. (1977). “FEAFLO: A program for the analysis of layered wood systems.” Comput. Struct., 7, 237–248.
Turkstra, C. J., and Madsen, H. O. (1980). “Load combinations and codified structural design.” J. Struct. Div. ASCE, 106(12), 2527–2543.
Vanderbilt, M. D., Goodman, J. R., Criswell, M. E., and Bodig, J. (1974). “A rational analysis and design procedure for wood joist floor systems.” Final Report for NSF (Grant No. GK-30853), Dept. of Civil Engineering, Colorado State Univ., Fort Collins, Colo.
Wen, Y. K. (1977). “Statistical combination of extreme loads.” J. Struct. Div. ASCE, 103(5), 1079–1093.
Wheat, D. L. (1980). “Nonlinear analysis of wood-joist floors.” PhD dissertation, Colorado State Univ., Fort Collins, Colo.
Wheat, D. L., Vanderbilt, M. D., and Goodman, J. R. (1983). “Wood floors with nonlinear nail stiffness.” J. Struct. Eng., 109(5), 1290–1302.
Yu, G. (2003). “Load sharing and system factors for light-frame wall systems.” PhD dissertation, Oregon State Univ., Corvallis, Or.
Yu, G., Rosowsky, D. V., and Bulleit, W. M. (2002). “Reliability of light-frame walls subject to combined axial and transverse loading.” Proc., World Conf. on Timber Engineering (WCTE 2002), (CD-ROM).
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 131 • Issue 9 • September 2005
Pages: 1444 - 1455
Copyright
© 2005 ASCE.
History
Received: May 19, 2002
Accepted: Jan 31, 2005
Published online: Sep 1, 2005
Published in print: Sep 2005
Notes
Note. Associate Editor: J. Daniel Dolan
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.