Load-Duration Behavior of Wood Connections
Publication: Journal of Structural Engineering
Volume 131, Issue 9
Abstract
The time-effect factors , used in design to account for the load-duration effect were developed through long-term testing of wood members in flexure, yet they are applied to wood connections as well. This study examines time-effect factors for steel-doweled wood connections. In this study, long-term tests were performed on small-scale wood connection specimens, and the resulting time-to-failure data were used to calibrate two cumulative damage (CD) models. A numerical approach was developed for calibrating existing CD models to the test data. Step load tests also were performed on full-scale bolted connection specimens and the results were compared to the results predicted by the CD models fit to the long-term data. The calibrated CD models were then used in a relatively simple procedure to determine an approximate for steel-doweled wood connections ASCE-16 stipulates a of 0.80 for both snow load and occupancy live load. The best fitting models for the long-term test data produced 7 and ’s, representative of live and snow load, respectively, between 0.68 and 0.70 for the CD model used in the United States code development and 0.74–0.78 for a model used in Canada. The models which fit step-load test results the best produced a range of 0.86–0.88.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to thank Mr. Zeno Martin and Mr. David Claus for their assistance in gathering the test data used in this study. This paper is based on work supported by the Cooperative State Research, Education, and Extension Service, U.S. Department of Agriculture, under Grant No. UNSPECIFIED97-35103-4897. Any opinions, findings, conclusions, or recommendations expressed in this publication are those of the writers and do not necessarily reflect the view of the U.S. Department of Agriculture.
References
American Forest and Paper Association (AF&PA). (1996). “Standard for load and resistance design for engineered wood structures.” Washington, D.C.
American Forest and Paper Association (AF&PA). (1997). “National design specification for wood construction.” Washington, D.C.
Barrett, J. D., and Foschi, R. O. (1978a). “Duration of load and probability of failure in wood. Part I: Modelling creep rupture.” Can. J. Civ. Eng., 5(4), 505–514.
Barrett, J. D., and Foschi, R. O. (1978b). “Duration of load and probability of failure in wood. Part II: Constant, ramp, and cyclic loadings.” Can. J. Civ. Eng., 5(4), 515–532.
Bodig, J., and Farquhar, B. J. M. (1988). “Behavior of mechanical joints of wood at accelerated strain rates.” Proc. 1988 International Conf. on Timber Engineering, Vol. 2, Forest Products Research Society, Madison, Wis., 455–464.
Bulleit, W. M., and Schoch, C. G. III (1986). “Simulation of load-duration effects in wood.” Wood Sci. Technol., 20, 157–167.
Ellingwood, B., and Rosowsky, D. V. (1991). “Duration of load effects in LRFD for wood construction.” J. Struct. Eng., 117(2), 584–599.
Foschi, R. O., and Barrett, J. D. (1982). “Load-duration effects in western hemlock lumber.” J. Struct. Div. ASCE, 108(7), 1494–1510.
Foschi, R. O., Folz, B. R., and Yao, F. Z. (1989). “Reliability-based design of wood structures. Structural research series.” Rep. No. 34, Dept of Civil Engineering, Univ. of British Columbia, Vancouver, Canada.
Foschi, R. O., and Yao, Z. C. (1986). “Another look at three duration of load models.” Proc. 17th IUFRO Congress, Paper No. 19:9-1, Florence, Italy.
Gerhards, C. C. (1979). “Time-related effects on wood strength: a linear cumulative damage theory.” Wood Sci., 11(3), 139–144.
Gerhards, C. C., and Link, C. L. (1983). “Use of a cumulative damage model to predict load-duration characteristics of lumber.” Proc., IUFRO Division 5 Conf., Madison, Wis.
Gerhards, C. C., and Link, C. L. (1987). “A cumulative damage model to predict load duration characteristics of lumber.” Wood Fiber Sci., 19(2), 147–164.
Haupt, H. (1867). General theory of bridge construction, Appleton, New York, 60–62.
Leijten, A. J. M. (1988). “Load-duration strength of joints with high working load levels.” Proc. 1988 International Conf. on Timber Engineering, Vol. 2, R. Y. Itani, ed., Forest Products Research Society, Madison, Wis, 465–473.
Liu, W.-F., and Bulleit, W. M. (1995). “Approximate reliability analysis of wood structural systems.” Struct. Safety, 17, 59–78.
MATLAB (2002), MATLAB, Version 6.0.042a, Release, The Mathworks. Inc., Natick, Mass.
Murphy, J. F., Ellingwood, B. R., and Hendrickson, E. M. (1987). “Damage accumulation in wood structural members under stochastic live loads.” Wood Fiber Sci., 19(4), 453–463.
National Forest Products Association (NFPA). (1991). “National design specification for wood construction.” Washington, D.C.
Rosowsky, D. V., and Bulleit, W. M. (2002). “Load duration effects in wood members and connections: Order statistics and critical loads.” Struct. Safety, 24, 347–362.
Rosowsky, D. V., and Reinhold, T. A. (1999). “Rate-of-load and duration-of-load effects for wood fasteners.” J. Struct. Eng., 125(7), 719–724.
van de Kuilen, J.-W.G., and Blass, H. J. (1996). “Does damage accumulate in timber joints loaded at load levels below 50% of the average short term strength¿” Proc., International Wood Engineering Conf., Vol. 4, Omnipress, Madison, Wis, 46–53.
Wood, L. W. (1951). “Relation of strength of wood to duration of load.” Rep. No. 1916, USDA Forest Service, Forest Products Laboratory, Madison, Wis.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Feb 2, 2003
Accepted: Nov 19, 2004
Published online: Sep 1, 2005
Published in print: Sep 2005
Notes
Note. Associate Editor: J. Daniel Dolan
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.