On-Line Control of Polymer Addition to Prevent Massive Sludge Washout
Publication: Journal of Environmental Engineering
Volume 125, Issue 11
Abstract
An experimental method that quantifies the effect of polymer dosing on sludge settling characteristics is proposed. This method consists of recording batch settling curves at a grid of sludge and polymer concentrations. The effect of the polymer was found to depend on the mixing time between the dosing of the polymer and the start of the batch sedimentation. The recorded effects could be successfully implemented in a 1D dynamic settler model. From the literature it was concluded that keeping the sludge blanket below a certain critical height is an effective way of controlling the effluent suspended solids. From a model-based analysis this strategy appeared to be sound. Different control strategies using, respectively, the sludge blanket height [feedback (FB)], the hydraulic loading [feedforward (FF)], the solids loading (FF), or the sludge volume loading (FF) were tested for their ability to keep the sludge blanket below the critical height. The control strategy based on the hydraulic loading was the least efficient with respect to minimizing polymer dosage. The others appeared equally effective provided that they were properly tuned. Using the excess of the critical sludge blanket height as a measure of effectiveness, strategies based on more than one measured variable appeared to be less sensitive to suboptimal tuning.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Albertson, O. E. ( 1992). “Clarifier design.” Design and retrofit of wastewater treatment plants for biological nutrient removal, C. W. Randall, J. L. Barnard, and H. D. Stensel, eds., Technomic Publishing, Lancaster, Pa., 185–254.
2.
Andrews, J. F., Stenstrom, M. K., and Buhr, H. O. (1976). “Control systems for the reduction of effluent variability from the activated sludge process.” Prog. Water Technol., 8(1), 41–68.
3.
“Arbeitsblat A 131—Bemessung von einstufigen Belebungsanlagen ab 5000 Einwohnerwerten.” (1991). Abwassertechnische Vereinigung e.V., St. Ausustin, Germany (in German).
4.
Bergh, S. G., and Olsson, G. (1996). “Knowledge based diagnosis of solids-liquid separation problems.” Water Sci. and Technol., 33(2), 219–226.
5.
Brent, R. P. (1973). Algorithms for minimization without derivatives. Prentice-Hall, Englewood Cliffs, N.J.
6.
Chancelier, J. P., Cohen de Lara, M., Joannis, C., and Pacard, F. (1997). “New insights in dynamic modeling of a secondary settler-I. Flux theory and steady-states analysis.” Water Res., 31, 1847–1856.
7.
Daigger, G. T. (1995). “Development of refined clarifier operating diagrams using an updated settling characteristics database.” Water Envir. Res., 67, 95–100.
8.
Deininger, A. (1994). “Influence of combined sewage influent on secondary clarifiers of activated sludge plants.” Water Sci. and Technol., 30(4), 67–70.
9.
Ekama, G. A., et al. (1997). “Secondary settling tanks: Theory, modeling, design and operation.” IAWQ Scientific and Tech. Rep. No. 6, IAWQ, London.
10.
Grijspeerdt, K., Bogaert, H., and Verstraete, W. (1996). “Design and verification of a model secondary clarifier for activated sludge.” J. Chem. Technol. Biot., 67, 404–412.
11.
Henze, M., Dupont, R., Grau, P., and De La Sota, A. (1993). “Rising sludge in secondary settlers due to denitrification.” Water Res., 27, 231–236.
12.
“Hydraulische en technologische aspecten van het nabezinkproces, 2 ronde nabezinktanks (Praktijkonderzoek).” (1981a). Stowa, Utrecht, The Netherlands 64p (in Dutch).
13.
Jeppsson, U. ( 1996). “Modelling aspects of wastewater treatment process,” PhD thesis, Lund University, Sweden.
14.
Krebs, P. (1995). “Success and shortcomings of clarifier modelling.” Water Sci. and Technol., 31(2), 181–191.
15.
Krebs, P., Vischer, D., and Gujer, W. (1995). “Inlet structure design for final clarifiers.”J. Envir. Engrg., ASCE, 121(8), 558–564.
16.
Lumely, D. J., Balmér, P., and Adamsson, J. (1988). “Investigations of secondary settling at a large treatment plant.” Water Sci. and Technol., 20(4–5), 133–142.
17.
Müller, J. R., and Krauth, K. (1998). “Wastewater flow management to maximise the capacity of sewage treatment plants.” Water Sci. and Technol., 37(9), 49–56.
18.
Nielsen, M. K., Carstensen, J., and Harremoes, P. (1996). “Combined control of sewer and treatment plant during rainstorm.” Water Sci. and Technol., 34(3–4), 181–187.
19.
Nyberg, U., Andersson, B., and Aspegren, H. (1996). “Real time control for minimizing effluent concentrations during stormwater events.” Water Sci. and Technol., 34(3–4), 127–134.
20.
Olsson, G. (1977). “State of the art in sewage treatment plant control.” AIChE Symp. Ser., 159(72), 52–76.
21.
Olsson, G., and Jeppsson, U. (1994). “Establishing cause-effect relationships in activated sludge plants—What can be controlled.” Proc., 8th Forum for Appl. Biotechnology, Bruges, University Gent, Belgium, Med. Fac. Landbouw. Univ., 59(4a), 2057–2070.
22.
“Overbelasting van nabezinktanks, Voordkomen van slibverlies met polyelectrolieten.” (1981b). Stowa, Utrecht, The Netherlands (in Dutch).
23.
Ozinsky, A. E., and Ekama, G. A. (1995). “Secondary settling tank modelling and design part 2: Linking sludge settleability measures.” Water SA, 21, 333–349.
24.
Shao, Y. J., Starr, M., Kaporis, K., Kim, H. S., and Jenkins, D. (1997). “Polymer addition as a solution to Nocardia foaming problems.” Water Environ. Res., 69, 25–27.
25.
Standard methods for the examination of water and wastewater. 18th Ed., American Public Health Association, Washington, D.C.
26.
Tsai, Y. P., Ouyang, C. F., Wu, M. Y., and Chiang, W. L. (1996). “Effluent suspended solids control of activated sludge process by fuzzy control approach.” Water Envir. Res., 68, 1045–1053.
27.
Vanderhasselt, A., and Verstraete, W. (1999). “Short-term effects of additives on sludge sedimentation characteristics.” Water Res., 33, 381–390.
28.
Van Haandel, A. C. (1992). “Activated sludge settling part II: Settling theory and application to design and optimisation.” Water SA, 18, 173–180.
29.
Vanrolleghem, P., Van Der Schueren D., Krikilion, G., Grijspeerdt, K., Willems, P., and Verstraete, W. (1996). “On-line quantification of settling properties with in-sensor-experiments in an automated settlometer.” Water Sci. and Technol., 33(1), 37–51.
30.
Vesilind, P. A. (1968). “Theoretical considerations: Design of prototype thickeners from batch settling tests.” Water and Sewage Works, 115–302.
31.
Wen, H. J., Liu, C. I., and Lee, D. J. (1997). “Size and density of flocculated sludge flocs.” J. Envir. Sci. Heal., 32(4), 1125–1137.
Information & Authors
Information
Published In
Journal of Environmental Engineering
Volume 125 • Issue 11 • November 1999
Pages: 1014 - 1021
History
Received: Dec 10, 1998
Published online: Nov 1, 1999
Published in print: Nov 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.