Journal of Irrigation and Drainage Engineering

This paper examines the problem of routing known water demands through gate-controlled, open-channel irrigation delivery systems. Volume-compensation principles were used to route multiple demands in multiple-pool canal systems. The volume-compensation method schedules each demand change individually under the assumption of a series of steady states and superimposes the individual results. Volume-compensation routing schedules were computed for two of the test cases proposed by the ASCE Task Committee on Canal Automation. Alternative routing schedules were computed with the gate-stroking method, which is an inverse solution of the unsteady-flow equations. Both solutions were tested through unsteady-flow simulation. While not as effective as gate-stroking solutions, volume-compensation solutions performed satisfactorily under ideal flow control conditions. When subjected to realistic operational constraints, specifically constraints on the flow regulation interval, and also to incorrect canal hydraulic roughness information, both methods performed similarly.

A nonlinear, constrained multivariable optimization routine is developed for deciding the optimal canal water release and linked to a canal hydraulic module (MIKE 11) and command hydrological module (MIKE SHE). The optimization routine is solved using the sequential quadratic programming (SQP) technique. The hydraulic and the hydrological modules are calibrated and validated independently, and the results are found to be satisfactory. The integrated optimization-simulation model is applied to the Right Bank Main Canal System of Kangsabati Irrigation Project, West Bengal, India. An improved rotational delivery schedule based on long-term field data analysis is also developed. Three simulation scenarios are considered. These are (1) MIKE 11 and MIKE SHE simulation, (3) integrated optimization simulation, and (3) integrated optimization-simulation with improved schedule. Simulations were performed for Kharif (rainy) irrigation periods for 3 different years (1995–1997). The intercomparison of the three simulation scenarios showed that the application of the integrated optimization-simulation model reduced the gap between irrigation water supply and crop water demand and improved the spatial distribution of supply, thereby, minimizing the tail-end deprivation.

The Alto Rio Lerma Irrigation District, located in the state of Guanajuato in Mexico, is an agricultural area whose sustainability depends partially upon groundwater withdrawal for crop irrigation. Because of high pumping demands and current land-management practices, groundwater levels have declined severely, resulting in aquifer overdraft. In order to analyze economic, environmental, and water use problems in this region, 12 potential cropping patterns were generated for different groundwater withdrawals using linear programming. Then, simulation of the agricultural system was performed using GLEAMS to estimate the amounts of water, nitrate, and pesticides in both runoff and percolation for each cropping pattern. Pumping costs and an aquifer exploitation coefficient account for the economic and environmental impacts of aquifer overdraft. Finally, the Range of Value Method (multicriteria method) was applied to rank and identify the best cropping pattern. The results show the best alternative for effectively balancing environmental with economic considerations was the farming practice, consisting of land leveling, growing vegetables such as red tomato, and controlled groundwater withdrawals to preserve aquifer sustainability.

The lateral lines of a drip irrigation system consist of pressurized pipelines with inline or online emitters. Proper hydraulic design of drip laterals usually requires the accurate evaluation of the total head losses, represented by friction losses along the pipe and the emitters, and local losses due to the emitter connections. This paper extends the local loss evaluation procedure, previously obtained for coextruded laterals, on the basis of new experiments. In addition, a simplified procedure was proposed based on the constant outlet discharge assumption for a quick evaluation of total head losses in drip irrigation lines, taking into account the total local loss due to the emitter connections. Total head loss values measured on 15 commercially available coextruded laterals were then compared with those obtained by using the nowly proposed methodology. Relative errors on the pressure head estimation for the examined cases were always $\pm$ 2.4%, and therefore the proposed methodology could serve for a quick, approximate evaluation of the total head losses along the laterals.

A methodology for estimating specific yield in shallow water environments using continuous soil moisture data is introduced. An accurate estimate of specific yield is critical for management of water resources affecting well yields, water levels, and rates of water level decline. The study area is located in an intensive small-scale hydrologic monitoring field site in Hillsborough County, Florida. Data from four soil moisture monitoring stations were studied. The objectives of this paper are to describe a methodology to obtain precise estimates of the specific yield that can be obtained by a fitting procedure and to determine functional relationships between measured soil parameters and soil moisture storage variability. Estimated specific yield values varied from zero, when the water table was near land surface, to a maximum that was close to drainable porosity consistent with a humid shallow water environment, where sensitive ecosystems and wetlands are dependent on a seasonal hydroperiod of water table fluctuations. The results will be incorporated into regional integrated surface and ground water models that are being applied successfully in West-Central Florida.

Analytical but approximate methods are developed for obtaining pumping induced rate and volume of stream flow depletion, which can account for unsteady (any variation) pumping discharge and are also applicable for intermittent pumping and recovery. Exact analytical solutions for a sinusoidal variation in the pumping discharge are proposed; the proposed methods are verified using these solutions. The proposed methods use ramp kernels that give results superior to the conventional convolution. These ramp kernels assume the linear variation in pumping discharge between the two consecutive discretized points as opposed to the uniform variation assumed in the conventional convolution. The proposed solutions are applicable for homogeneous and isotropic aquifers hydraulically connected to streams.

Optimal design equations for a parabolic canal section are presented in this paper. The design equations for a minimum earthwork cost section and a minimum cost lined section are in explicit form and result in optimal dimensions of a canal in single step computations. These have been obtained after applying the Fibbonaci search method on a nonlinear unconstrained optimization problem. The study also addresses the bounds on the canal dimensions and the velocity of flow. A nondimensional parameter approach has been used to simplify the analysis, and a set of graphs for nondimensional parameters are presented as an alternative for design. Design procedures for different cases have been presented to demonstrate the simplicity of the method.

Water is a limited resource in agricultural production in arid climates. Under such conditions, high irrigation efficiency can be obtained either through implementation of efficient irrigation systems such as drip or sprinkler systems or through the age-old practice of deficit irrigation with gravity systems. The method used to increase irrigation efficiency is often dictated by economic and/or social factors. In either case, the effectiveness of water management at the farm level needs to be evaluated by measuring irrigation efficiency. The objective of this study was to evaluate the irrigation efficiencies for three crops in Southern New Mexico using the chloride technique. The chloride technique is a simple method in which the natural chloride in the irrigation water is used as a tracer to estimate the leaching fraction and the irrigation efficiency at the farm level. Soil samples were collected from various fields in 15 cm increments to a depth of 180 cm at the end of the irrigation season. The samples were analyzed for moisture and chloride content. In addition to the chloride technique, on-farm irrigation efficiencies were measured using applied water, yield, and water production functions. Water production functions and yields were used to estimate total evapotranspiration while flow measurements were used to calculate the amount of applied water. The results showed that high irrigation efficiency can be accomplished using deficit irrigation. Irrigation efficiency values ranged from 83 to 98%. Irrigation efficiencies using the chloride technique were compared with efficiencies estimated from direct flow measurements. The differences between the two methods ranged from 2 to 11.4%. The results showed that even though the chloride technique is subject to sampling errors and simplified theoretical assumptions, it can be used to estimate on-farm irrigation efficiency with considerable accuracy.

A power-law channel is a generalized form of the parabolic channel. The exponent of the governing equation is a variable that for certain maximum permissible side slopes can be determined by maximizing the cross-sectional area of flow (or minimizing the wetted perimeter). Using this exponent rather than the constant allows a hydraulically more efficient open channel section to be designed. In earlier work on power-law channels freeboard was neglected to simplify the analysis. However as pointed out by several authors, a channel without freeboard is of academic interest only and not practical. All open channels are in practice designed and constructed with freeboard as a factor of safety. In this paper freeboard has been introduced as an additional parameter to be taken into account when designing a power-law channel. The work from this paper is applied to an earlier example of a parabolic channel to demonstrate a practical design.