Journal of Bridge Engineering

Welded plate girder bridges built before the mid-1980s are often susceptible to fatigue cracking driven by out-of-plane distortion. However, methods for prediction of secondary stresses are not specifically addressed by bridge design specifications. This paper presents a finite-element study of a two-girder bridge that developed web gap cracks at floortruss-girder connections. The modeling procedures performed in this research provide useful strategies that can be applied to determine the magnitude of distortion-induced stresses, to describe the behavior of crack development, and to assess the effectiveness of repair alternatives. The results indicate severe stress concentration at the crack initiation sites. The current repair method used at the positive moment region connections is found acceptable, but that used at the negative moment region connections is not satisfactory, and additional floortruss member removal is required. Stress ranges can be lowered below half of the constant amplitude fatigue threshold, and fatigue cracking is not expected to recur if the proposed retrofit approach is carried out.

Precast bridges are often constructed as single span for dead load, but continuous for live load. A diaphragm connection is provided for negative moment continuity. However, the connection may also be subjected to positive moments due to time-dependent effects. Because these moments may be large enough to damage the diaphragm or even the girders, a positive moment connection is often provided. This paper reports on a study to determine the types of positive moment connections used across the country and to identify potential problems with these types of connections. A questionnaire survey was conducted to assess the state of practice for precast prestressed concrete bridges made continuous. The survey provides valuable information on this type of bridge and updates a previous survey on this subject.

The current American Association of State Highway and Transportation Officials (AASHTO) Load and Resistance Factor Design (LRFD) Specifications impose fairly strict limits on the use of its live-load distribution factor for design of highway bridges. These limits include requirements for a prismatic cross section, a large span-length-to-width ratio, and a small plan curvature. Refined analyses using 3D models are required for bridges outside of these limits. These limits place severe restrictions on the routine design of bridges in California, as box-girder bridges outside of these limits are frequently constructed. This paper presents the results of a study investigating the live-load distribution characteristics of box-girder bridges and the limits imposed by the LRFD specifications. Distribution factors determined from a set of bridges with parameters outside of the LRFD limits are compared with the distribution factors suggested by the LRFD specifications. For the range of parameters investigated, results indicated that the current LRFD distribution factor formulas generally provide a conservative estimate of the design bending moment and shear force.

The design, technology, and construction of a small road bridge made of very high performance fiber-reinforced concrete is described in this paper. The bridge consists of precast prestressed concrete beams with a cast-in-place ordinary concrete deck. A preliminary experimental investigation was conducted to define the mix design, to establish the properties of the material and its durability, and to study the flexural behavior of the prestressed concrete beams with and without the concrete deck. The effect of steel fibers at the structural level, where there is an influence of constitutive behavior and size effects, was analyzed by testing a prestressed beam using very high performance fiber-reinforced concrete without fibers. The establishment of the structural properties of the material then allowed the design of the final section of the bridge beams and the definition of a model to justify the design rules adopted. This project represents an attempt to demonstrate the industrial feasibility of very high performance concrete structural elements manufactured with conventional raw materials and usual production techniques and to evaluate the production technology when utilizing steel fibers.

There is a tendency for traffic loads to increase with the passage of time. It is not uncommon, therefore, for bridges to be strengthened and/or widened or sometimes to have lanes or even complete decks added. A few bridges were designed initially with a view to future expansion, such as the George Washington Suspension Bridge, designed to accommodate an extra deck, and the Salazar (now April 25) Bridge, designed to have two train tracks added, but these are exceptions. Suspension bridges behave somewhat differently from other bridge types, and the methods for increasing capacity can also be different. Some ideas are presented of how suspension bridges can be altered to accommodate more load, be it automobile, pedestrian, or even train traffic, and some examples are given. The importance of understanding both structural behavior and structural safety is emphasized.

Cable reliability analysis involves the combined evaluation of cable capacity and cable load in a probabilistic manner. Assessment of cable capacity is only possible through visual inspections of the wires, field sampling, laboratory analysis of the degraded wire populations, and analytical techniques. In addition to a brief presentation of cable mechanics and deterministic models that approximate cable strength, this paper discusses inspection methodologies and statistical methods of estimation of the sizes of the degraded wire populations, and wire properties, leading to cable capacities. These capacities are described by probability distributions. The paper also discusses fundamentals of reliability analysis as they apply to bridge cables. Load criteria of present standard specifications (such as AASHTO or other international codes) are not applicable to long-span suspension bridges. The paper discusses criteria of bridge loading and reliability indices for bridge cables. More work is needed in the evaluation of loading for long-span bridges.

Truck weight-limit regulations have significant influence on truck operating weights. These regulations directly influence loads applied to highway facilities, such as bridges and pavements. “Truck weight” herein collectively refers to a vehicle’s gross weight, axle weights, and axle configuration. Truck load spectra as a result of truck weight limits are important to bridge engineering in many respects, such as that of determining requirements for evaluation and design of bridges for both strength and fatigue. This paper’s objective is to present a new method for predicting truck weight spectra resulting from a change in truck weight limits. This method is needed to estimate impacts of the change on highway bridges such as accelerated fatigue accumulation. Historical and recent truck weight data are used to test and illustrate the proposed method, and the results show its good prediction capability. This method is also applied here to an example of estimating the impact on steel bridge fatigue due to a possible increase in the gross-vehicle-weight limit from 356 kN (80 kips) on five axles to 431 kN (97 kips) on six axles. Also included is an investigation of the AASHTO fatigue truck model for steel bridge evaluation. Results show that the current fatigue truck model may become invalid under the studied scenario of truck weight-limit increase.

Final design of the replacement orthotropic deck panels for the rehabilitation of the Williamsburg Bridge in New York City was based on laboratory fatigue tests of a full-scale prototype and an as-built orthotropic deck panel carried out at Lehigh University in the latter 1990s. The tests focused on determining and comparing the fatigue resistance of two different welded rib-to-diaphragm connection details that were recommended in the 1994 AASHTO LRFD Bridge Design Specifications and an alternative proposed by Steinman. The test on the prototype panel demonstrated that the fatigue resistance of the alternative detail was superior and influenced additional design changes that were incorporated into the replacement panels installed on the southern inner and outer roadways. Subsequent tests on the as-built panel further confirmed that the fatigue resistance of the alternative detail was superior and demonstrated that the additional design changes were also beneficial. Static and dynamic tests revealed the complex behavior of the orthotropic deck panels and demonstrated the effectiveness of retrofit and repair options at cracked connections. An assessment of fatigue resistance based on fracture mechanics models provided theoretical correlation. This research has led to the revision of design specifications for steel orthotropic decks first provided in the 2000 Interim AASHTO LRFD Specifications.

This paper presents experimental investigations on Bailey bridges. Seven one-sixth scale models of the Bailey bridge trussed-steel frame were constructed in the laboratory and tested. All members of the scale models of steel frames are solid rectangular sections. Both ends of the members are fully welded. Some members of three selected specimens were removed to study their effects on degradation of limit loads. The cross-section areas of some members in two of the specimens were reduced to simulate the phenomenon of member corrosion. Two numerical methods, second-order elastic and inelastic analyses are used to predict the behavior of the steel frames. The responses determined by numerical methods are compared with test results. The scale model without lateral bracing members collapsed in the global lateral buckling mode at a very small limit load. The lateral bracing system of a planar frame is very important for preventing an early collapse and allows the ultimate strength to be reached.