Journal of Bridge Engineering

An experimental investigation was conducted to determine the susceptibility of grouted stay cables to bending fatigue damage. The results from twelve, bending fatigue tests are reported in this paper. Fretting of adjacent wires within a single strand was the dominant cause of bending fatigue damage in the grouted stay-cable specimens. This damage tended to be concentrated at the ends of the specimens and at locations where concentrated loads were applied to the stays. The laboratory tests indicated that the risk of bending fatigue damage was low at the tension rings, along the free length of the stays, and in the vicinity of unintentionally crossed strands.

In the absence of intensive wind tunnel tests, this study provides an effective and accurate approach to estimate the operational driving speed limit on bridges subjected to different road conditions and wind intensities, through a convenient continuous simulation technique (CSP). A fast and vigorous simulation tool, vehicle performance simulation, is developed to effectively model the performance of vehicles traveling on bridges by considering the interactions between wind, vehicles, and the bridge. The CSP, on the other hand, dramatically reduces the data generation time and makes a reliability analysis of vehicles possible. The application of the proposed method on the Confederation Bridge in Canada is presented as a numerical example. The simulation result overrides the general impression that only high-sided vehicles are sensitive to wind attacks, and this work demonstrates that light-weighted vehicles are also likely to suffer from instability problems on bridges under relatively low wind velocity. In addition, different types of vehicle can undergo different instability mechanisms under the same wind condition and these vehicle instability mechanisms vary with wind velocity.

Stonecutters Bridge is the second longest cable-stayed bridge in the world and the first major bridge with a twin-box girder superstructure. It has a number of innovative structural features which made the construction of the bridge a significant challenge. This paper describes the fabrication and erection procedures for the bridge towers and the main span superstructure. These were developed in close interaction between the contractor and his construction engineering consultant to ensure a safe and effective construction. A stage-by-stage analysis was set up to model every step of the main span erection. The results were first used in the verification analyses to establish the adequacy of the permanent works throughout construction. In parallel, extensive wind tunnel testing as well as numerical analyses were performed to ascertain the effects of typhoon wind loads on the structure. The structural deformations predicted by the erection analysis were incorporated into a comprehensive geometric control procedure. This paper describes the construction methodologies developed and the related engineering input. It outlines studies undertaken to achieve an effective construction, ensure structural adequacy of all erection stages, ascertain an acceptable aerodynamic performance of the bridge, and exercise full control over the bridge geometry throughout erection.

As part of an effective bridge management system, sensor networks can provide data to support both inspection and assessment. Wireless sensor networks (WSNs) have the potential to offer significant advantages over traditional wired monitoring systems in terms of sensor, cabling, and installation costs as well as expandability. However, there are drawbacks with WSNs relating to power, data bandwidth, and robustness. To evaluate the potential of WSNs for use in bridge management, a network of seven sensor nodes was installed on the Ferriby Road Bridge, a three-span reinforced concrete bridge. Three displacement transducer nodes were placed across cracks on the soffit of the bridge to measure the change in crack width. Three inclinometer sensor nodes were mounted on two of the elastomeric bearing pads to measure the change in inclination of the bearing pads while a final node monitored temperature in the box that contained the gateway. The installation of the WSN is discussed and data from this network is analyzed. Finally, the use of sensor networks to support inspection and assessment is discussed.

Many transportation agencies are now evaluating and rating their inventory of steel truss bridge gusset plate connections after the collapse of the I35W Bridge in Minneapolis. Modern design methodologies are being used to evaluate inventory gusset plate connections that were designed using allowable stress methods. One such implementation is evaluation of gusset plates using block shear, an approach that was developed well after many of the nation’s truss bridges were designed. Vintage designs commonly used the Whitmore section to proportion gusset plate connections. Differences between rating outcomes from block-shear analysis at strength conditions with designs that employed allowable stresses on the Whitmore section method were identified and expected outcomes for rating of gusset plate connections are proposed. Examples are shown to highlight the similarities and differences in these two approaches to assist rating engineers in implementation and expected variabilities on the outcomes based on connection geometric proportions and material properties.

In New Mexico, many reinforced concrete slab (RCS) bridges provide service on interstates I-10, I-25, and I-40. The load rating for this type of bridge largely depends on the live-load moment in the slab. Consequently, the objective of this study was to determine a more accurate value for the equivalent strip width using higher level evaluation techniques. A continuous RCS bridge was evaluated starting with an AASHTO load and resistance factor rating analysis. A diagnostic test was then conducted to measure live-load strains which showed that the slab stiffness fit within cracked and gross section behavior. Furthermore, slab moments from finite element analysis agreed reasonably well with experimental moments derived using the average of the cracked and gross section modulus. From refined analysis, the equivalent strip widths for positive moment were 26.1 and 22.1% greater than those calculated by the AASHTO approximate method for the exterior and interior spans, respectively. The refined widths for negative moment were greater than AASHTO by 13.1 and 11.1%. This increase in the equivalent strip width reduced the live-load effects, which proportionally increased the rating factors.

The paper focuses on the reliability-based design optimization of gravity wall bridge abutments when subjected to active condition during earthquakes. An analytical study considering the effect of uncertainties in the seismic analysis of bridge abutments is presented. Planar failure surface has been considered in conjunction with the pseudostatic limit equilibrium method for the calculation of the seismic active earth pressure. Analysis is conducted to evaluate the external stability of bridge abutments when subjected to earthquake loads. Reliability analysis is used to estimate the probability of failure in three modes of failure viz. sliding failure of the wall on its base, overturning failure about its toe (or eccentricity failure of the resultant force) and bearing failure of foundation soil below the base of wall. The properties of backfill and foundation soil below the base of abutment are treated as random variables. In addition, the uncertainties associated with characteristics of earthquake ground motions such as horizontal seismic acceleration and shear wave velocity propagating through backfill soil are considered. The optimum proportions of the abutment needed to maintain the stability are obtained against three modes of failure by targeting various component and system reliability indices. Studies have also been made to study the influence of various parameters on the seismic stability.

Smith was one of the premier bridge builders of the post-Civil War period. He started his bridge building career under Albert Fink on the Louisville and Nashville Railroad. During the Civil War, he designed and built a powder factory for the Confederacy at Augusta, Ga. After the war, he formed Smith and Latrobe Co. and later The Baltimore Bridge Company with Benjamin and C. H. Latrobe. He worked closely with James Eads on the St. Louis Bridge and designed and built the long iron easterly approach to the bridge. He designed and built some of the major viaducts, swing, and fixed span bridges in the United States, Australia, and Peru, and finally innovative cantilever bridges over the Kentucky, Mississippi, and St. Lawrence Rivers.

To predict characteristic extreme traffic load effects, simulations are sometimes performed of bridge loading events. To generalize the truck weight data, statistical distributions are fitted to histograms of weight measurements. This paper is based on extensive weight-in-motion measurements from two European sites and shows the sensitivity of the characteristic traffic load effects to the fitting process. A semiparametric fitting procedure is proposed: direct use of the measured histogram where there are sufficient data for this to be reliable and parametric fitting to a statistical distribution in the tail region where there are less data. Calculated characteristic load effects are shown to be highly sensitive to the fit in the tail region of the histogram.