Limit Analysis for Local and Overall Stability of a Slurry Trench in Cohesive Soil
Publication: International Journal of Geomechanics
Volume 15, Issue 5
Abstract
This paper uses limit analysis to develop a two-dimensional (2D) and a three-dimensional (3D) analysis of slurry trench local and overall stability for cohesive soil. Formulas for the slurry trench stability analysis are obtained through theoretical derivation based on limit analysis theory, and rotational mechanisms are then presented for slurry trench stability. For 2D slurry trench local and overall stability, the failure surface has the shape of a circular arc, whereas it has the shape of spherical cap for 3D local stability, and it has the shape of a torus with an outline defined by a circle for 3D overall stability. Examples are provided to illustrate the safety factor influenced by the slurry and soil bulk density ratio, slurry level depth and trench depth ratio, thickness of the weak soil layer, cohesion, and trench width and depth ratio. The safety factor for the 3D solutions is approximately 1.1 times greater than the safety factor for the 2D solutions for local stability but 1.2 times greater () for overall stability.
Introduction
Slurry trenches are used in the construction of groundwater cutoff walls and subsurface structural diaphragm walls. The stability of slurry trenches has attracted great attention among geotechnical researchers and the industry itself because instability of the slurry trench is common in underground engineering. The safety factor is an important index in the design of the slurry trench, but little research has been carried out on the subject (Choy et al. 2007; Fox 2004; Morgenstern and Amir-Tahmasseb 1965; Wong 1984).
With a slurry trench, the slope angle is 90° and the slope face has slurry pressure action. To date, the existing methods for determining slope stability have been classified into the following three types.
The limit equilibrium method has been commonly used in practice because of its relative simplicity. This method is based on discretization into slices, in which global static equilibrium conditions are satisfied. Basically, they are based on assumptions of the interslice forces to make the problem statically (Ahmed et al. 2012; Alejano et al. 2011; Mendjel and Messast 2012; Tinti and Manucci 2008).
Finite-element modeling, based on continuum mechanics, can be used to determine deformations under loading or the safety factor by numerical iterations. An appropriate constitutive model for the soil mass in the slope is needed with these models. With finite-element modeling, both soil movement and progressive failure can be estimated (Srivastava et al. 2010; Stolle and Guo 2008; Xu 2011).
Limit analysis, based on plasticity limit theorems, has an advantage in that the lower- and upper-bound theorems bracket the true solution. This approach is rigorous so that the stress field with a lower-bound solution is in equilibrium and yield criterion at every point in the soil; the velocity field with an upper-bound solution is compatible with flow rule and the imposed displacements. In recent years, great efforts have been devoted to the application of the plasticity limit theorems to slope stability (Kumar and Sahoo 2012; Li et al. 2010; Loukidis et al. 2003; Michalowski 2010; Yang and Yang 2010).
The overall stability of trenches has been addressed numerous times; however, a limit analysis for local stability of slurry trenches has not been reported. This paper aimed to develop a two-dimensional (2D) and a three-dimensional (3D) analysis of slurry trench local and overall stability for cohesive soil. Formulas for slurry trench stability analysis are obtained through theoretical derivation based on the limit analysis theory, and rotational mechanisms are then presented for slurry trench stability. Numerical examples are provided to illustrate the safety factor influenced by the trench width and depth ratio (), thickness of the weak soil layer (), cohesion (), slurry and soil bulk density ratio (), distance from the slurry level to the trench top, and trench width ratio ().
Limit Analysis for Slurry Trench Stability
The application of limit analysis to earth slopes started with a paper by Drucker and Prager (1952), who applied the kinematic approach of limit analysis to the stability of slopes undergoing plane-strain failure. Limit analysis aims to evaluate bounds on the limit load inducing or resisting failure in structures built of perfectly plastic materials. In the application to slurry trenches, the limit load can be identified by the weight of the soil. An upper bound can be obtained from the kinematic method, in which the kinematically admissible velocity field defines the possible mechanism of failure. The strain rates resulting from the velocity field must satisfy the flow rule that is associated with the yield condition of the material, and the velocities must satisfy the boundary conditions. The most common yield condition used for undrained, purely cohesive soils is the Tresca hexagonal yield criterion. The flow rule requires the following relationship among the principal strain rates for problems of plane plastic flow:where and = principal strain rates. The mode of deformation in the transition layer is a combination of the shear flow parallel to the layer with the extension normal to it. The dissipation rate can be written aswhere = dissipation of energy; = variational symbol; = cohesion stress of the soil; and = tangential velocity change.
(1)
(2)
The work rate of the soil weight () can be calculated as the dot product of the total weight of a block and the velocity of the block centroid The work rate of the slurry pressure () can be calculated as the dot product of the pressure () of the slurry and the velocity of the interface of the soil and the slurry ()For a slurry trench of a given geometry, it is possible to evaluate the safety factor, defined asEquating the external rate of work to the rate of internal energy dissipation, a least upper bound for the safety factor can be obtained.
(3)
(4)
(5)
Limit Analysis for Local Stability Of Slurry Trench
Slurry-supported trenches are excavated in soft soil or sand. When the liquid level fluctuations are too large or the surface decreases sharply, a local instability and overexcavation phenomenon often occur (Fig. 1), which leads to an increase in the filling factor of the concrete and impermeable material. Therefore, the amount of construction materials and the difficulty are increased. Fig. 2 shows an example of concrete filling caused by instability. Redundant concrete must be drilled and removed in subsequent construction, which is wasteful, increases the difficulty, and increases the noise and damage to adjacent buildings.
2D Local Stability
Soils are described as purely cohesive when their shear strength is independent of the level of stress. This is typical of clays subjected to undrained conditions. Constructing rotational mechanisms for such soils is relatively simple, because their deformation occurs without volume change. Fig. 3 shows a kinematically admissible velocity field. The rotating mechanism has the shape of a cylinder. This mechanism was considered earlier by Baligh and Azzouz (1975) and Gens et al. (1988).
The bow-shaped CFD (a surface of velocity discontinuity shown in Fig. 3) rotates about the center of rotation with the materials below the surface CFD remaining at rest. Thus, the surface CFD is a surface of velocity discontinuity.
It is very complicated to determine the direct integration of the external work rate due to the soil weight in the region CFD. An easier alternative is to first find the area centroid and the velocity vector at the centroid. The rate of external work for the region CFD is then found by the dot product of the soil weight concentrated at its volume centroid and the velocity vector at the centroid.
The weight of CFD, which is instable and rotational, can be calculated by the following equation:where and are shown in Fig. 3.
(6)
The work rate of the soil weight can be written aswhere = unit weight of soil; and = angular velocity of the region CFD for rotation.
(7)
The internal dissipation of energy occurs along the discontinuity surface CFD. The total internal dissipation of energy is found by integration over the whole surface.
The internal dissipation of energy can be computed asThe rate of external work due to the slurry pressure occurs along the surfaces and . The rate of external work due to the slurry pressure is found by integration over the whole surface.
(8)
The rate of external work due to the slurry pressure on isThe rate of external work due to the slurry pressure on iswhere = unit weight of the slurry in the trench; and = distance from the slurry level to the weak layer soil.
(9)
(10)
The total rate of external work due to the slurry pressure isThe safety factor () in Eq. (5) can then be obtained by substituting Eqs. (7), (8), and (11) into Eq. (5) as follows:where = thickness of the weak soil layer; and = medivariation. The function has a minimum value when satisfies the condition .
(11)
(12)
3D Local Stability
The actual instability of a slurry trench is a 3D problem, so one must consider the 3D space effects when the length of the slurry trench is short. Fig. 4 shows a 3D rotational mechanism in cohesive soils (undrained behavior), with a spherical failure surface confined to the vertical portion of the slurry trench. This mechanism is often used to analyze slope instability problems (Griffiths and Marquez 2008; Hungr et al. 1989; Silvestri 2006); a special case of mechanisms was considered earlier by Baligh and Azzouz (1975).
The weight of spherical cap CFD isThe work rate of the soil weight was obtained as the dot product of the soil weight concentrated at its volume centroid and the centroid velocity vector, yieldingThe work dissipation rate isThe rate of external work due to the slurry pressure occurs along the surface , but the rate is found by integration over the whole surface.
(13)
(14)
(15)
The rate of external work due to the slurry pressure on isThe rate of external work due to the slurry pressure on isThe total rate of external work due to the slurry pressure isThe safety factor () in Eq. (5) can then be obtained by substituting Eqs. (14), (15), and (18) into Eq. (5) as follows:in which the functions and are defined asThe function has a minimum value when satisfies the condition .
(16)
(17)
(18)
(19)
Limit Analysis for Overall Stability of Slurry Trench
2D Overall Stability
In cohesive soil (, ), the slip surface is usually assumed to be circular (Baligh and Azzouz 1975; Hungr et al. 1989; Silvestri 2006). In this study, a circular slip surface is assumed for the overall stability analysis of a slurry trench in cohesive soil, as shown in Fig. 5.
The circular slip surface is described bywhere is shown in Fig. 5. Hence, the magnitude of the velocity vector along this surface varies according towhere = magnitude of the velocity at point . From the geometrical relations, it may be shown that the values and can be expressed in terms of the angles and in the formFollowing Ausilio et al. (2000), the work rate of the soil weight () can be written aswhere = angular velocity of the region for rotation. The functions , , and will be explained in Eqs. (34)–(36).
(21)
(22)
(23)
(24)
(25)
The internal dissipation of energy occurs along the discontinuity surface . The total internal dissipation of energy () is found by integration over the whole surfaceThe slurry velocity () during rotation about axis isThe slurry pressure iswhere the functions , , and are defined by Eqs. (29)–(31)The total rate of external work () due to the slurry pressure isThe safety factor () in Eq. (5) can then be obtained by substituting Eqs. (25), (26), and (32) into Eq. (5) as follows:in which the functions , , , , , , and are defined aswhereThe function has a minimum value when and satisfy the conditionsSolving these equations and substituting the values of and thus obtained into Eq. (33) yields a least upper bound for the safety factor, , of a slurry trench.
(26)
(27)
(28)
(29)
(30)
(31)
(32)
(33)
(34)
(35)
(36)
(37)
(38)
(39)
(40)
(41)
(42)
3D Overall Stability
Soils are described as purely cohesive (, ) when their shear strength is independent of the level of stress. This is typical of clays subjected to undrained conditions. Constructing rotational mechanisms for such soils is relatively simple, because their deformation occurs without volume change. Consequently, the surface of revolution provides a torus surface, as illustrated in Fig. 6. The similar shape of this mechanism was considered by Michalowski and Drescher (2009) and Xia et al. (2012).
The trace of the mechanism on the symmetry plane is described by two circular arcs, and . The equation for the torus surface is given byWith the circular arcs and defining the shape of the failure surface in Fig. 6 given in Eq. (43), the centerline of the conical volume and the radius of the circular cross section are found asTo calculate the work of the soil weight, a local coordinate system , was introduced, as shown in Fig. 6. The velocity during rotation about axis iswhere = angular velocity, and the infinitesimal volume element isThe work rate of the soil weight () can be written aswhere the functions , , , , will be defined by Eqs. (53) and (54).
(43)
(44)
(45)
(46)
(47)
The internal dissipation of energy () can be computed byThe slurry velocity during rotation about axis isThe slurry pressure iswhere the functions , , and are defined by Eqs. (29)–(31).
(48)
(49)
(50)
The total rate of external work () due to the slurry pressure isThe safety factor () in Eq. (5) can then be obtained by substituting Eqs. (47), (48), and (51) into Eq. (5) as follows:In Eqs. (47), (48), (51), and (52), , , , , , , , and are functions of the soil strength parameters and the geometry of the slip surface, which can be defined as follows:The function has a minimum value when , , and satisfy the conditionsThe safety factor of a slurry trench also can be calculated with Eq. (58). To avoid lengthy computations, these simultaneous equations may be solved by a numerical procedure. The minimum is calculated with independent variable parameters , , and .
(51)
(52)
(53)
(54)
(55)
(56)
(57)
(58)
Results and Discussion
It is commonly accepted that 3D analyses yield safety factors for slopes that are greater than those from 2D analyses (Li et al. 2010; Tutluoglu et al. 2011). This statement is supported by direct comparison of analytical results and by intuition, because 2D analysis is less restrictive. Michalowski (2010) offered a more formal justification for the statement that a 2D safety factor for a uniform slope cannot be greater than that from a 3D analysis. Based on the 2D and 3D mechanisms for slurry trench local and overall stability, examples are presented in this section to demonstrate the difference between 2D and 3D models.
Comparison between 2D and 3D Solutions of Local Stability
For slurry trench local stability, the estimates of safety factor were obtained using a procedure for a given slurry and soil bulk density ratio, thickness of the weak soil layer, cohesion, and soil bulk density. The independent variable in the procedure was angle . These parameters were varied by a small increment in computational loops, and the process was repeated until the minimum of was reached, with the increments of 0.01° used for angle . The results of these computations are represented graphically in Figs. 7–9 for 2D and 3D solutions.
Fig. 7 illustrates the distribution of the safety factor versus the slurry and soil bulk density ratio (). It can be seen that increasing the from to can increase the factor of safety by more than 23% (2D) and 21% (3D). The safety factors for the 3D solutions are approximately 1.08 and 1.1 times greater than the safety factors for the 2D solutions for and , respectively.
Fig. 8 shows the distribution of the safety factor versus the thickness of the weak soil layer (). It can be seen that increasing the from to can decrease the factor of safety by more than 49.6% (2D) and 53.4% (3D). The safety factors for the 3D solutions are approximately 1.1 and 1.13 times greater than the safety factors for the 2D solutions for and , respectively.
Fig. 9 presents the distribution of the safety factor versus cohesion (). It can be seen that increasing the from to can increase the factor of safety by more than 24.8% (2D) and 28.4% (3D). The safety factors for the 3D solutions are approximately 1.12 and 1.08 times greater than the safety factors for the 2D solutions for and , respectively.
The following special example of slurry trench local stability has the following parameters: slurry and soil bulk density ratio , thickness of the weak soil layer , cohesion , and soil bulk density . Therefore, the calculated 2D and 3D safety factors are 1.18 and 1.31, respectively. For the selected geometric parameters (no slurry), a value of was obtained by Michalowski and Drescher (2009) using the cylindrical surface failure mechanism, and a value of was obtained by Baligh and Azzouz (1975) using the spherical cap failure mechanism. Because slurry pressure prevents the slope from failing, as the slurry pressure increases, the safety factor becomes larger and larger.
Comparison between 2D and 3D Solutions of Overall Stability
The estimates of safety factor were obtained using a procedure for a given slurry and soil bulk density ratio, slurry level depth and trench depth ratio, cohesion, trench width and depth ratio (in 3D), soil bulk density, and trench depth. Independent variables in the procedure were angles and and ratio (in 3D). These parameters were varied by a small increment in computational loops, and the process was repeated until the minimum of was reached, with the increments of 0.1° used for angles and and 0.01 for ratio . The results of these computations are represented graphically in Figs. 5–9 for 2D and 3D solutions.
This section examines the difference between 2D and 3D models for various parameters, including , , , and . To facilitate comparison of 2D and 3D calculations, in the 3D cases.
Fig. 10 illustrates the distribution of the safety factor versus the slurry and soil bulk density ratio () for various trench width and depth ratios (). As expected, the safety factor of the slurry trench increases as increases. From this figure, the slurry and soil bulk density ratio, , is found to have a great effect on the solutions. It can be seen that increasing the from to can increase the factor of safety by more than 19.6% (2D) and 15.6% (). The safety factors for the 3D solutions are approximately 1.38, 1.18, 1.05, and 1.04 times greater than the safety factors for the 2D solutions for , , , and , respectively.
Fig. 11 shows the distribution of the safety factor versus the slurry level depth and trench depth ratio (). The safety factor of the slurry trench decreases as increases. From this figure, the slurry level depth and trench depth ratio, , is found to have a great effect on the solutions. It can be seen that increasing the from to can decrease the factor of safety by more than 36.4% (2D) and 31.2% (). The safety factors for the 3D solutions are approximately 1.42, 1.21, 1.05, and 1.03 times greater than the safety factors for the 2D solutions for , , , and , respectively.
Fig. 12 presents the distribution of the safety factor versus cohesion (). The safety factor of the slurry trench increases as increases. From this figure, the cohesion, , is found to have a great effect on the solutions. It can be seen that increasing the from to can increase the factor of safety by more than 23.3% (2D) and 28.4% ().The safety factors for the 3D solutions are approximately 1.32, 1.16, 1.04, and 1.03 times greater than the safety factors for the 2D solutions for , , , and , respectively.
Fig. 13 illustrates the distribution of the safety factor versus the trench width and depth ratio () in the 3D cases. As expected, the safety factor of the slurry trench decreases with increasing trench width and depth ratio. From this figure, the trench width and depth ratio, , is found to have a great effect on the chart solutions when . It can be seen that increasing the from to can decrease the factor of safety by more than 13%. This means that the 3D boundary effect on slurry trench stability is very large when . As shown in Fig. 13, this difference changes by less than 1% when the ratio of increases from 5 to 10. This implies that the 3D end boundary effect decreases more significantly with an increasing ratio for the slurry trench. It also means that the 3D boundary end effect on slurry trench stability is small and is almost insignificant when .
The example of slurry trench overall stability has the following parameters: slurry and soil bulk density ratio , slurry level depth and trench depth ratio , cohesion , soil bulk density , and trench depth . The calculated 2D and 3D () safety factors are 0.92 and 1.12, respectively. For the selected geometric parameters (no slurry), a value of was obtained using the cylindrical surface failure mechanism, and was obtained using the torus failure mechanism by Michalowski and Drescher (2009).
Conclusions
The upper-bound methods for the 2D and the 3D analysis of slurry trench local and overall stability for cohesive soil are presented in this paper. Formulas for the stability analysis of a slurry trench are obtained through theoretical derivation based on limit analysis theory. Rotational mechanisms are presented for slurry trench stability. For 2D slurry trench local and overall stability, the failure surface has the shape of a circular arc, whereas for 3D local stability, it has the shape of a spherical cap, and it has the shape of torus with an outline defined by a circle for 3D overall stability.
Examples are provided to illustrate variations in the safety factor with the following parameters: slurry and soil bulk density ratio, slurry level depth and trench depth ratio, thickness of weak soil layer, cohesion, trench width and depth ratio, soil bulk density, and trench depth. The stability factor increases with increasing slurry and soil bulk density ratio and cohesion, and with decreasing slurry level depth and trench depth ratio, thickness of the weak soil layer, trench width and depth ratio, soil bulk density, and trench depth.
Based on the comparisons between 2D and 3D solutions, the 3D effects tend to lose significance when . It can be concluded that when using limit analysis, 2D solutions can replace 3D solutions for preliminary slurry trench design where . Based on the results presented, the following conclusions can be made:
1.
Using the limit analysis theory, the 2D and 3D solutions for the local and overall stability analysis of slurry trench are obtained; for the application example presented, the safety factors for the 3D solutions are approximately 1.1 times greater than the safety factors for the 2D solutions for local stability but 1.2 times greater () for overall stability.
2.
The slurry and soil bulk density ratio is found to have a great effect on the solutions; increasing the from to can increase the factor of safety by more than 23% (2D) and 21% (3D) for local stability, and by 19.6% (2D) and 15.6% () for overall stability.
3.
The safety factor of a slurry trench decreases as the slurry level depth and trench depth ratio increases for overall stability; increasing the from to can decrease the factor of safety by more than 53.7% (2D) and 51.5% ().
4.
The boundary effect is found to reduce with increasing trench width and depth ratio for the 3D slurry trench; in addition, the safety factors for the 3D slurry trenches are almost unchanged when .
Acknowledgments
This research was supported financially by the Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20110073120012), the Shanghai Pujiang Talent plan (Grant No. 11PJ1405700), and the National Natural Science Foundation of China (Grant Nos. 41002095, 41172251, and 41272317).
References
Ahmed, A., Ugai, K., and Yang, Q. Q. (2012). “Assessment of 3D slope stability analysis methods based on 3D simplified Janbu and Hovland methods.” Int. J. Geomech., 81–89.
Alejano, L. R., Ferrero, A. M., Ramirez-Oyanguren, P., and Fernandez, M. I. A. (2011). “Comparison of limit-equilibrium, numerical and physical models of wall slope stability.” Int. J. Rock Mech. Min. Sci., 48(1), 16–26.
Ausilio, E., Conte, E., and Dente, G. (2000). “Seismic stability analysis of reinforced slopes.” Soil. Dyn. Earthquake Eng., 19(3), 159–172.
Baligh, M. M., and Azzouz, A. S. (1975). “End effects on stability of cohesive slopes.” J. Geotech. Engrg. Div., 101(GT11), 1105–1117.
Choy, C. K., Standing, J. R., and Mair, R. J. (2007). “Stability of a loaded pile adjacent to a slurry-supported trench.” Géotechnique, 57(10), 807–819.
Drucker, D. C., and Prager, W. (1952). “Soil mechanics and plastic analysis or limit design.” Q. Appl. Math., 10(2), 157–165.
Fox, P. J. (2004). “Analytical solutions for stability of slurry trench.” J. Geotech. Geoenviron. Eng., 749–758.
Gens, A., Hutchinson, J. N., and Cavounidis, S. (1988). “Three-dimensional analysis of slides in cohesive soils.” Géotechnique, 38(1), 1–23.
Griffiths, D. V., and Marquez, R. M. (2008). “Three-dimensional slope stability analysis by elasto-plastic finite elements.” Géotechnique, 57(6), 537–546.
Hungr, O., Salgado, F. M., and Byrne, P. M. (1989). “Evaluation of a three-dimensional method of slope stability analysis.” Can. Geotech. J., 26(4), 679–686.
Kumar, J., and Sahoo, J. P. (2012). “Upper bound solution for pullout capacity of vertical anchors in sand using finite elements and limit analysis.” Int. J. Geomech., 333–337.
Li, A. J., Merifield, R. S., and Lyamin, A. V. (2010). “Three-dimensional stability charts for slopes based on limit analysis methods.” Can. Geotech. J., 47(12), 1316–1334.
Loukidis, D., Bandini, P., and Salgado, R. (2003). “Stability of seismically loaded slopes using limit analysis.” Géotechnique, 53(5), 463–479.
Mendjel, D., and Messast, S. (2012). “Development of limit equilibrium method as optimization in slope stability analysis.” Struct. Eng. Mech., 41(3), 339–348.
Michalowski, R. L. (2010). “Limit analysis and stability charts for 3D slope failures.” J. Geotech. Geoenviron. Eng., 583–593.
Michalowski, R. L., and Drescher, A. (2009). “Three-dimensional stability of slopes and excavations.” Géotechnique, 59(10), 839–850.
Morgenstern, N., and Amir-Tahmasseb, I. (1965). “The stability of a slurry trench in cohesionless soils.” Géotechnique, 15(4), 387–395.
Silvestri, V. (2006). “A three-dimensional slope stability problem in clay.” Can. Geotech. J., 43(2), 224–228.
Srivastava, A., Babu, G., and Haldar, S. (2010). “Influence of spatial variability of permeability property on steady state seepage flow and slope stability analysis.” Eng. Geol., 110(3–4), 93–101.
Stolle, D., and Guo, P. (2008). “Limit equilibrium slope stability analysis using rigid finite elements.” Can. Geotech. J., 45(5), 653–662.
Tinti, S., and Manucci, A. (2008). “A new computational method based on the minimum lithostatic deviation (MLD) principle to analyse slope stability in the frame of the 2-D limit-equilibrium theory.” Nat. Hazards Earth Syst. Sci., 8(4), 671–683.
Tutluoglu, L., Oge, I. F., and Karpuz, C. (2011). “Two and three dimensional analysis of a slope failure in a lignite mine.” Comput. Geosci., 37(2), 232–240.
Wong, G. C. Y. (1984). “Stability analysis of slurry trenches.” J. Geotech. Eng., 1577–1590.
Xia, X.-H., Han, C.-Y., and Wang, J.-H. (2012). “Analytical solutions for three-dimensional stability of limited slopes.” J. Shanghai Jiaotong Univ. (Science), 17(2), 251–256.
Xu, J. (2011). “Debris slope stability analysis using three-dimensional finite element method based on maximum shear stress theory.” Environ. Earth Sci., 64(8), 2215–2222.
Yang, F., and Yang, J. S. (2010). “Stability of shallow tunnel using rigid blocks and finite-element upper bound solutions.” Int. J. Geomech., 242–247.
Information & Authors
Information
Published In
Copyright
This work is made available under the terms of the Creative Commons Attribution 4.0 International license, http://creativecommons.org/licenses/by/4.0/.
History
Received: Feb 2, 2012
Accepted: Oct 31, 2012
Published online: Nov 3, 2012
Published in print: Oct 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.