Energetic and Exergetic Analyses of Experimentally Investigated Hybrid Solar Air Heater
Publication: Journal of Energy Engineering
Volume 149, Issue 1
Abstract
Solar energy is a type of renewable energy that is readily available, but it must be converted to a usable form using a highly efficient method. The global energy problem that has surfaced in recent years shows the importance of both practical and scientific studies on using solar energy for space heating. Solar air heaters are large volume systems used for space heating. Research on the geometry and surface forms of solar air collectors is focused on reducing system volume and optimizing the use of solar energy. A photovoltaic (PV) module can be cooled with a fluid to prevent a decrease in efficiency due to heat while generating electrical power. The subject of this study is the idea of using the heat from cooling the modules to support a solar air heater. The improvement of the thermal performance of a solar air collector with a cooling thermal load of the concentrated photovoltaic thermal collector (CPV/T) was experimentally investigated. The heat exchanger, which removes the heat of the water-ethylene glycol circulating in the photovoltaic thermal collector, is mounted in the solar air heater’s chamber of one of the two identical solar air heaters, and the first hybrid unit was obtained (i.e., first unit). The ordinary one was called the second unit. Heated air left the first and second units at average temperatures of 45.87°C and 38.83°C, respectively. Although the airflow rates in the units are the same, the air temperature in the first unit was increased by 18.13%. The heat contribution of the heat exchanger to the first unit was 128.96 W. The first and second law efficiencies of the first and second units were calculated as 51.89%, 15.22%, and 45.4%, 10.34%, respectively. The energetic and exergetic improvement of the first unit was found to be 6.49% and 4.88%, respectively. The local solar utilization capability is and for the first and second units, respectively. The waste heat from the CPV/T collector cooling cycle, which is , was recovered for heating air in the first unit. The recovery of waste heat for use in the first unit provided a significant performance improvement over the second unit. The environmental contribution of the waste heat recovery means 144 kg emission per year less in emission release.
Practical Applications
This study addresses the process of supporting the performance of a solar air heater with the waste heat obtained during the liquid cooling application of a CPV/T collector. The heat exchanger of a closed loop that cools a CPV/T collector was placed in the solar air heater’s chamber of the first solar air heater unit. The heat released from the heat exchanger increased the unit’s heating capacity. The improvement achieved with the first unit compared to the second unit is evaluated by comparing it to the second unit but without a heat exchanger attachment. While solar utilization in the first unit reached 525.19 W, the second unit provided 401 W of solar utilization. The energy and exergy values of the first and second units were found to be 51.89%, 15.22%, and 45.4%, 10.34%. When evaluating the use of solar energy instead of fossil fuel-based heating applications, it is predicted that the local gain can be and . In recent years, active cooling of PV modules is a popular method to prevent a decrease in module efficiency due to a rise in the PV module temperature. Gaining use of the thermal load removed from the PV module is another well-known subject. In this study, of thermal load from the CPV/T collector was recovered to the heating air in the first unit. In this way, the efficiency of the first and second laws of the first unit increased by 6.49% and 4.88%, respectively, compared to the second unit. The idea of the hybrid solar air heater contributes to researchers working in this field and raises awareness among practitioners.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
No data, models, or code were generated or used during the study.
Acknowledgments
The authors gratefully acknowledge the financial support of the Coordinatorship of Research Projects (CRP), Karabuk University, Karabuk, Turkey, under Project No. KBUBAP-17-YL-245. We would like to thank Ipragaz Corporation and Solarus Sunpower BV for their support in providing CPV/T collectors.
References
Abdullah, A. S., M. I. Amro, M. M. Younes, Z. M. Omara, A. E. Kabeel, and F. A. Essa. 2020. “Experimental investigation of single pass solar air heater with reflectors and turbulators.” Alexandria Eng. J. 59 (2): 579–587. https://doi.org/10.1016/j.aej.2020.02.004.
Ahmed, O. K., K. I. Hamada, and A. M. Salih. 2022. “Performance analysis of PV/Trombe with water and air heating system: An experimental and theoretical study.” Energy Sources Part A 44 (1): 2535–2555. https://doi.org/10.1080/15567036.2019.1650139.
Akpinar, E. K. 2010. “Drying of mint leaves in a solar dryer and under open sun: Modelling, performance analyses.” Energy Convers. Manage. 51 (12): 2407–2418. https://doi.org/10.1016/j.enconman.2010.05.005.
Bakirci, K., and Y. Kirtiloglu. 2022. “Effect of climate change to solar energy potential: A case study in the eastern Anatolia region of Turkey.” Environ. Sci. Pollut. Res. 29 (2): 2839–2852. https://doi.org/10.1007/s11356-021-14681-0.
Chabane, F., N. Moummi, and S. Benramache. 2014. “Experimental study of heat transfer and thermal performance with longitudinal fins of solar air heater.” J. Adv. Res. 5 (2): 183–192. https://doi.org/10.1016/j.jare.2013.03.001.
Daghigh, R., and A. Shafieian. 2016. “An experimental study of a heat pipe evacuated tube solar dryer with heat recovery system.” Renewable Energy 96 (May): 872–880. https://doi.org/10.1016/j.renene.2016.05.025.
Debnath, S., B. Das, and P. Randive. 2020. “Energy and exergy analysis of plain and corrugated solar air collector: Effect of seasonal variation.” Int. J. Ambient Energy 43 (1): 2796–2807. https://doi.org/10.1080/01430750.2020.1778081.
El-Said, E. M. S., M. A. Gohar, A. Ali, and G. B. Abdelaziz. 2022. “Performance enhancement of a double pass solar air heater by using curved reflector: Experimental investigation.” Appl. Therm. Eng. 202 (Feb): 117867. https://doi.org/10.1016/j.applthermaleng.2021.117867.
Frondel, M., and S. A. Schubert. 2021. “Carbon pricing in Germany’s road transport and housing sector: Options for reimbursing carbon revenues.” Energy Policy 157 (Oct): 112471. https://doi.org/10.1016/j.enpol.2021.112471.
Guclu, Y. 2011. “The determination of sea tourism season with respect to climatical conditions on the black sea region of Turkey.” Procedia Social Behav. Sci. 19 (Jan): 258–269. https://doi.org/10.1016/j.sbspro.2011.05.131.
Gunerhan, H., and A. Hepbasli. 2007. “Exergetic modeling and performance evaluation of solar water heating systems for building applications.” Energy Build. 39 (5): 509–516. https://doi.org/10.1016/j.enbuild.2006.09.003.
Guo, J., Z. Du, G. Liu, X. Yang, and M. J. Li. 2022a. “Compression effect of metal foam on melting phase change in a shell-and-tube unit.” Appl. Therm. Eng. 206 (11): 118124. https://doi.org/10.1016/j.applthermaleng.2022.118124.
Guo, J., Z. Liu, B. Yang, X. Yang, and J. Yan. 2022b. “Melting assessment on the angled fin design for a novel latent heat thermal energy storage tube.” Renewable Energy 183 (Jan): 406–422. https://doi.org/10.1016/j.renene.2021.11.007.
Guo, J., X. Wang, B. Yang, X. Yang, and M. J. Li. 2022c. “Thermal assessment on solid-liquid energy storage tube packed with non-uniform angled fins.” Sol. Energy Mater. Sol. Cells 236 (1): 111526. https://doi.org/10.1016/j.solmat.2021.111526.
Hachchadi, O., M. Bououd, and A. Mechaqrane. 2021. “Performance analysis of photovoltaic-thermal air collectors combined with a water to air heat exchanger for renewed air conditioning in building.” Environ. Sci. Pollut. Res. 28 (15): 18953–18962. https://doi.org/10.1007/s11356-020-08052-4.
Holman, J. P. 2011. Experimental methods for engineers. New York: McGraw Hill.
Ihoume, I., R. Tadili, N. Arbaoui, A. Bazgaou, A. Idrissi, M. Benchrifa, and H. Fatnassi. 2022. “Performance study of a sustainable solar heating system based on a copper coil water to air heat exchanger for greenhouse heating.” Sol. Energy 232 (12): 128–138. https://doi.org/10.1016/j.solener.2021.12.064.
IRENA (International Renewable Energy Agency). 2021. “Renewable capacity statistics 2021.” Accessed August 5, 2022. https://www.irena.org/publications/2021/March/Renewable-Capacity-Statistics-2021.
Kalogirou, S. A., S. Karellas, K. Braimakis, C. Stanciu, and V. Badescu. 2016. “Exergy analysis of solar thermal collectors and processes.” Prog. Energy Combust. Sci. 56 (Feb): 106–137. https://doi.org/10.1016/j.pecs.2016.05.002.
Kumar, A., A. P. Singh, and O. P. Singh. 2022. “Investigations for efficient design of a new counter flow double-pass curved solar air heater.” Renewable Energy 185 (Dec): 759–770. https://doi.org/10.1016/j.renene.2021.12.101.
Kumar, S., and S. K. Verma. 2022. “Heat transfer and fluid flow analysis of sinusoidal protrusion rib in solar air heater.” Int. J. Therm. Sci. 172 (10): 107323. https://doi.org/10.1016/j.ijthermalsci.2021.107323.
Kushwah, A., A. Kumar, M. Kumar, and A. Pal. 2021. “Garlic dehydration inside heat exchanger-evacuated tube assisted drying system: Thermal performance, drying kinetic and color index.” J. Stored Prod. Res. 93 (21): 101852. https://doi.org/10.1016/j.jspr.2021.101852.
Omojaro, A. P., and L. B. Y. Aldabbagh. 2010. “Experimental performance of single and double pass solar air heater with fins and steel wire mesh as absorber.” Appl. Energy 87 (12): 3759–3765. https://doi.org/10.1016/j.apenergy.2010.06.020.
Ozturk, H. H., and Y. Demirel. 2004. “Exergy-based performance analysis of packed-bed solar air heaters.” Int. J. Energy Res. 28 (5): 423–432. https://doi.org/10.1002/er.974.
Petela, R. 1964. “Exergy of heat radiation.” ASME J. Heat Transf. 86 (2): 187–192. https://doi.org/10.1115/1.3687092.
Peyghambarzadeh, S. M., S. H. Hashemabadi, S. M. Hoseini, and M. Seifi Jamnani. 2011. “Experimental study of heat transfer enhancement using water/ethylene glycol based nanofluids as a new coolant for car radiators.” Int. Commun. Heat Mass Transf. 38 (9): 1283–1290. https://doi.org/10.1016/j.icheatmasstransfer.2011.07.001.
Potgieter, M. S. W., C. R. Bester, and M. Bhamjee. 2020. “Experimental and CFD investigation of a hybrid solar air heater.” Sol. Energy 195 (Jan): 413–428. https://doi.org/10.1016/j.solener.2019.11.058.
Prakash, O., A. Kumar, S. K. Dey, and A. Aman. 2022. “Exergy and energy analysis of sensible heat storage based double pass hybrid solar air heater.” Sustainable Energy Technol. Assess. 49 (Feb): 101714. https://doi.org/10.1016/j.seta.2021.101714.
Qu, M., X. Yan, H. Wang, Y. Hei, H. Liu, and Z. Li. 2022. “Energy, exergy, economic and environmental analysis of photovoltaic/thermal integrated water source heat pump water heater.” Renewable Energy 194 (Jun): 1084–1097. https://doi.org/10.1016/j.renene.2022.06.010.
Roy, S., Y. F. Lam, M. U. Hossain, and J. C. L. Chan. 2022. “Comprehensive evaluation of electricity generation and emission reduction potential in the power sector using renewable alternatives in Vietnam.” Renewable Sustainable Energy Rev. 157 (Sep): 112009. https://doi.org/10.1016/j.rser.2021.112009.
Shapsough, S., and I. Zualkernan. 2022. “An IoT-based services infrastructure for utility-scale distributed solar farms.” Energies 15 (2): 440. https://doi.org/10.3390/en15020440.
Shrivastava, A., J. Prakash Arul Jose, Y. Dilip Borole, R. Saravanakumar, M. Sharifpur, H. Harasi, R. K. Abdul Razak, and A. Afzal. 2022. “A study on the effects of forced air-cooling enhancements on a 150 W solar photovoltaic thermal collector for green cities.” Sustainable Energy Technol. Assess. 49 (2): 101782. https://doi.org/10.1016/j.seta.2021.101782.
Silva, G. M., A. G. Ferreira, R. M. Coutinho, and C. B. Maia. 2020. “Thermodynamic analysis of a sustainable hybrid dryer.” Sol. Energy 208 (Aug): 388–398. https://doi.org/10.1016/j.solener.2020.08.014.
Singh, S., and J. Ru. 2022. “Accessibility, affordability, and efficiency of clean energy: A review and research agenda.” Environ. Sci. Pollut. Res. 29 (13): 18333–18347. https://doi.org/10.1007/s11356-022-18565-9.
Sivakumar, S., K. Siva, and M. Mohanraj. 2019. “Experimental thermodynamic analysis of a forced convection solar air heater using absorber plate with pin-fins.” J. Therm. Anal. Calorim. 136 (1): 39–47. https://doi.org/10.1007/s10973-018-07998-5.
Suki, N. M., N. M. Suki, A. Sharif, S. Afshan, and K. Jermsittiparsert. 2022. “The role of technology innovation and renewable energy in reducing environmental degradation in Malaysia: A step towards sustainable environment.” Renewable Energy 182 (Jan): 245–253. https://doi.org/10.1016/j.renene.2021.10.007.
Wang, D., J. Liu, Y. Liu, Y. Wang, B. Li, and J. Liu. 2020. “Evaluation of the performance of an improved solar air heater with ‘S’ shaped ribs with gap.” Sol. Energy 195 (13): 89–101. https://doi.org/10.1016/j.solener.2019.11.034.
Yang, X., J. Guo, B. Yang, H. Cheng, P. Wei, and Y. L. He. 2020. “Design of non-uniformly distributed annular fins for a shell-and-tube thermal energy storage unit.” Appl. Energy 279 (Dec): 115772. https://doi.org/10.1016/j.apenergy.2020.115772.
Yang, X., X. Wang, Z. Liu, X. Luo, and J. Yan. 2022. “Effect of fin number on the melting phase change in a horizontal finned shell-and-tube thermal energy storage unit.” Sol. Energy Mater. Sol. Cells 236 (Mar): 111527. https://doi.org/10.1016/j.solmat.2021.111527.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Jun 18, 2022
Accepted: Sep 28, 2022
Published online: Nov 26, 2022
Published in print: Feb 1, 2023
Discussion open until: Apr 26, 2023
ASCE Technical Topics:
- Air temperature
- Architectural engineering
- Building systems
- Energy efficiency
- Energy engineering
- Energy sources (by type)
- Engineering fundamentals
- Engineering mechanics
- HVAC
- Hybrid methods
- Measurement (by type)
- Methodology (by type)
- Renewable energy
- Solar power
- Solar thermal power
- Temperature (by type)
- Temperature effects
- Temperature measurement
- Thermal effects
- Thermal properties
- Thermodynamics
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.