Multiobjective Optimization of Double-Wall Cooling Structure of Integrated Strut Flame Stabilizer and Sensitivity Analysis of Parameters
Publication: Journal of Aerospace Engineering
Volume 36, Issue 5
Abstract
The thermal environment behind the integrated strut of the afterburner is very harsh. A double-wall structure is set at the integrated strut flame stabilizer for cooling. The multiobjective optimization of the double-wall cooling structure is carried out by using the RBFNN-coupled nondominated sorting genetic algorithm II (NSGA-II), and the complex interaction between the film outflow and the mainstream was explored based on the numerical simulation results. The effects of geometric parameters and external working conditions on the cooling performance of the double wall are studied based on the Sobol method. The results show that the upward spiral vortex behind the strut will press the film outflow to form an irregular air film on the wall, effectively protecting the trailing edge of the strut. The optimized double-wall structure has a better air film coverage effect, and the comprehensive cooling performance has been improved to a certain extent. Compared with the geometric parameters, the mass-flow rate of the cooling gas per unit area has a greater impact on the comprehensive cooling performance of the double wall. The temperature ratio of the main and secondary flows has little effect on the comprehensive cooling performance of the double wall.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This study was supported by the National Science and Technology Major Project, China (No. J2019-III-0019-0063).
References
Afzal, A., H. Chung, K. Muralidhar, and H. Hee Cho. 2019. “Neural-network-assisted optimization of rectangular channels with intersecting ribs for enhanced thermal performance.” Heat Transfer Eng. 41 (18): 1609–1625. https://doi.org/10.1080/01457632.2019.1661693.
Chen, Y., Y. Fan, Q. Han, X. Shan, Y. Bi, and Y. Deng. 2022. “The influence of cooling air jets on the premixed flame structure and stability of air-cooled bluff-body flameholder.” Fuel 310 (Feb): 1222239. https://doi.org/10.1016/j.fuel.2021.122239.
Desclaux, J., and J. Serre. 2003. “M88-2E4: Advanced new generation engine for Rafale multirole fighter.” In Proc., AIAA Int. Air and Space Symp. and Exposition: The Next 100 Years. San Diego: American Institute of Aeronautics and Astronautics. https://doi.org/10.2514/6.2003-2610.
Dhanalakshmi, P., S. Palanivel, and V. Ramalingam. 2009. “Classification of audio signals using SVM and RBFNN.” Expert Syst. 36 (3): 6069–6075. https://doi.org/10.1016/j.eswa.2008.06.126.
Du, L. W. 2020. “Influence of lobe inward penetration angle on performance of integrated afterburner.” Sci. Technol. Eng. 20 (12): 4992–4999.
Ebrahimi, H. B. 2013. “Overview of gas turbine augmentor design, operation, and combustion oscillation.” In Proc., AIAA/ASME/SAE/ASEE Joint Propulsion Conf. & Exhibit. San Diego: American Institute of Aeronautics and Astronautics. https://doi.org/10.2514/6.2006-4916.
Gaku Sasaki, T. T., T. M. Taku Nonomura, and K. Y. Akira Oyama. 2014. “Multi-objective optimization of airfoil for mars exploration aircraft.” Int. J. Aeronaut. Space Sci. 12 (29): 59–64. https://doi.org/10.2322/tastj.12.Pk_59.
Guo, J., G. Lin, X. Bu, and H. Li. 2020. “Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body.” Chin. J. Aeronaut. 33 (1): 161–175. https://doi.org/10.1016/j.cja.2019.08.025.
Huang, X., and H. R. Wang. 2018. “Numerical simulation analysis of a cavity strut flame stabilizer cold flow field influence on ignition characteristics.” Gas Turbine Exp. Res. 31 (5): 11–16.
Ji, H. M., Y. J. Fan, and M. L. Yang. 2006. “Feasibility analysis of a new inner dumped afterburner concept.” Aeroengine 2006 (1): 35–37.
Jia, X. Z., Y. Shan, X. P. Xu, C. Y. Zhou, J. Z. Zhang, and X. M. Tan. 2021. “Numerical study on cold flow characteristics of integrated afterburner.” J. Aerosp. Power 36 (7): 1472–1480. https://doi.org/10.13224/j.cnki.jasp.20200437.
Kalyanmoy Deb, A. M., A. Pratap, S. Agarwal, and T. Meyarivan. 2002. “A fast and elitist multiobjective genetic algorithm.” IEEE Trans. Evol. Comput. 6 (2): 182–197. https://doi.org/10.1109/4235.996017.
Kim, K. M., H. Moon, J. S. Park, and H. H. Cho. 2014. “Optimal design of impinging jets in an impingement/effusion cooling system.” Energy 66 (1): 839–848. https://doi.org/10.1016/j.energy.2013.12.024.
Lethander, A. T., K. A. Thole, G. Zess, and J. Wagner. 2003. “Optimizing the vane-endwall junction to reduce adiabatic wall temperatures in a turbine vane passage.” In Turbo Expo 2003, Parts A and B, 711–721. Atlanta, GA: International Gas Turbine Institute.
Li, F., R. Q. Guo, L. X. Li, T. Liu, X. P. Xu, J. C. Gao, and S. T. Shang. 2012. “Numerical simulation of characteristics for afterburner with integrated flow plate and flameholder.” Aeroengine 38 (5): 6–9. https://doi.org/10.1115/GT2003-38939.
Lin, S., R. Wu, S. W. Ruan, K. T. Wei, and B. Wang. 2021. “Investigation on cold flow field and performance of afterburner with different structures.” Aircr. Des. 41 (5): 53–58. https://doi.org/10.19555/j.cnki.1673-4599.2021.05.012.
Liu, G. H., Y. Y. Liu, and Y. Xie. 2018. “Effect of cavity on combustion characteristics of integrated strut flame stabilizer.” J. Aerosp. Power 33 (8): 1838–1844. https://doi.org/10.13224/j.cnki.jasp.2018.08.006.
Liu, Y. Y., C. Y. Zhou, Y. Xie, and G. H. Liu. 2020. “Preliminary experiment on the lean blow-off of an integrated cavity-based strut flameholder.” J. Aerosp. Power 35 (1): 75–80. https://doi.org/10.13224/j.cnki.jasp.2020.01.009.
Lovett, J. A., T. P. Brogan, D. S. Philippona, B. V. Kiel, and T. V. Thompson. 2015. “Development needs for advanced afterburner designs.” In Proc., AIAA/ASME/SAE/ASEE Joint Propulsion Conf. & Exhibit. San Diego: American Institute of Aeronautics and Astronautics. https://doi.org/10.2514/6.2004-4192.
Lubarsky, E., C. Cross, J. Cutright, B. Zinn, and P. Magari. 2008. “Novel carbureted flameholder for improved afterburner stability.” In Proc., 46th AIAA Aerospace Sciences Meeting and Exhibit. San Diego: American Institute of Aeronautics and Astronautics. https://doi.org/10.2514/6.2008-98.
Nossent, J., P. Elsen, and W. Bauwens. 2011. “Sobol’ sensitivity analysis of a complex environmental model.” Environ. Modelling Software 26 (12): 1515–1525. https://doi.org/10.1016/j.envsoft.2011.08.010.
Qin, W. L., X. M. He, Y. Jin, and B. Jiang. 2012. “Experimental investigation on cold flow characteristics of afterburner with cavity/strut hybrid flameholders.” J. Aerospace Power 27 (6): 1347–1354. https://doi.org/10.13224/j.cnki.jasp.2012.06.017.
Shang, S. T., M. Cheng, D. C. Liu, P. F. Xie, and F. Li. 2013. “State and developing trend for aeronautics propulsion technology.” Aviat. Manuf. Technol. 2013 (9): 72–74. https://doi.org/10.16080/j.issn1671-833x.2013.09.013.
Sun, Y. C., Z. X. Zhang, J. N. Li, and X. C. Zhang. 2011. “Design and numerical research of integrated rear frame and afterburner.” Aeronaut. Sci. Technol. 2011 (4): 71–74.
Sun, Z., C. Wang, Y. Zheng, J. Bai, and Q. Fu. 2020. “Non-intrusive reduced-order model for predicting transonic flow with varying geometries.” Chin. J. Aeronaut. 33 (2): 508–519. https://doi.org/10.1016/j.cja.2019.12.014.
Tan, X. M., Y. F. Li, and J. Z. Zhang. 2012. “Numerical investigation on structures of Lamilloy.” J. Mech. Eng. 48 (18): 144–149. https://doi.org/10.3901/JME.2012.18.144.
Wadia, A. R., and F. D. James. 2001. “F110-GE-132: Enhanced power through low-risk derivative technology.” J. Turbomach. 123 (3): 544–551. https://doi.org/10.1115/1.1378301.
Wang, Z., B. Thomas, W. Zhang, and D. Gu. 2022. “A novel random angular bend (RAB) algorithm and DEM modeling of thermal cracking responses of sandstone.” Geomech. Energy Environ. 10 (8): 2352–3808. https://doi.org/10.1016/J.GETE.2022.100335.
Wei, S., Y. Li, X. Gao, K. Y. Lee, and L. Sun. 2020. “Multi-stage sensitivity analysis of distributed energy systems: A variance-based Sobol method.” J. Mod Power Syst. Clean Energy 8 (5): 895–905. https://doi.org/10.35833/MPCE.2020.000134.
Wu, D., J. Jin, H. M. Ji, and S. Xu. 2011. “Experimental study of vortex shedding frequency at trailing edge of a cavity-based strut.” Aeroengine 37 (4): 48–50.
Wu, H., W. Niu, S. Wang, and S. Yan. 2021. “Sensitivity analysis of control parameters errors and current parameters to motion accuracy of underwater glider using Sobol’ method.” Appl. Ocean Res. 110 (1): 102625. https://doi.org/10.1016/j.apor.2021.102625.
Wu, R., S. W. Ruan, and Q. Jiang. 2020. “Numerical simulation study on performance of typical structure integrated afterburner.” Inf. Rec. Mater. 21 (3): 238–241. https://doi.org/10.16009/j.cnki.cn13-1295/tq.2020.03.149.
Yin, C. M., R. C. Zhang, W. J. Fan, Q. Shi, and W. L. Qin. 2018. “Numerical simulation on a type of the integrated afterburner.” J. Aerosp. Power 33 (2): 470–476. https://doi.org/10.13224/j.cnki.jasp.2018.02.026.
Yu, X. H., D. L. Quan, S. L. Liu, D. C. Xu, and Z. G. Hu. 2004. “Investigation of the internal heat transfer characteristics of double impingement plates.” J. Propul. Technol. 2004 (1): 36–38. https://doi.org/10.13675/j.cnki.tjjs.2004.01.010.
Zhang, W., C. Wu, Y. Li, L. Wang, and P. Samui. 2019. “Assessment of pile drivability using random forest regression and multivariate adaptive regression splines.” Georisk: Assess. Manage. Risk Eng. Syst. Geohazards 15 (1): 27–40. https://doi.org/10.1080/17499518.2019.1674340.
Zhang, W., C. Wu, H. Zhong, Y. Li, and L. Wang. 2021. “Prediction of undrained shear strength using extreme gradient boosting and random forest based on Bayesian optimization.” Geosci. Front. 12 (1): 469–477. https://doi.org/10.1016/j.gsf.2020.03.007.
Zhang, X. C., Y. C. Sun, and T. Liu. 2014. “Summary of advanced afterburner design technology.” Aeroengine 40 (2): 24–30. https://doi.org/10.13477/j.cnki.aeroengine.2014.02.006.
Zhao, N. F., X. M. Tan, Y. F. Li, R. L. Fang, and H. S. Xu. 2014. “Research on structures of high-density laminate porous plates.” J. Propul. Technol. 35 (11): 1517–1522. https://doi.org/10.13675/j.cnki.tjjs.2014.11.012.
Zhao, S., and Y. Fan. 2020. “Experimental and numerical study on the flame characteristics and cooling effectiveness of air-cooled flame holder.” Energy 209 (Oct): 118421. https://doi.org/10.1016/j.energy.2020.118421.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Mar 1, 2022
Accepted: Mar 20, 2023
Published online: Jun 5, 2023
Published in print: Sep 1, 2023
Discussion open until: Nov 5, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.