Effect of Inherent Anisotropy on the Triaxial Compression Behavior of Coral Sand
Publication: International Journal of Geomechanics
Volume 23, Issue 5
Abstract
A series of triaxial tests were carried out on two types of coral sand to study the inherent anisotropy behavior under triaxial stress conditions. Notably, monotonic drained and undrained tests and cyclic drained tests were conducted. At the same time, the effect of inherent anisotropy on particle breakage and the relationship between the relative breakage and the input energy were investigated. The test results show that the coral sand demonstrates very evident anisotropic behavior under triaxial stress conditions. In the monotonic tests, the effective peak friction angle and compressibility of coral sand decrease with the depositional angle, and the anisotropic behavior is more significant at low confining pressures. The axial and volumetric strains of the low-depositional-angle specimens increase faster with the number of cycles in the cyclic drained tests. In addition, the relative breakage increases with the confining pressure but decreases with the depositional angle. A unique relationship exists between the relative breakage and the input energy for the specimens with the same depositional angle, but the relative breakage decreases with the depositional angle at the same input energy.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The study was supported by the National Natural Science Foundation of China (Grant No. 51978305), which is gratefully acknowledged.
Notation
The following symbols are used in this paper:
- AR, S, and C
- aspect ratio, sphericity, and convexity;
- Br
- relative breakage (Hardin 1985);
- BrDsieve, BrDFmin, BrDFmax, and BrDeq
- relative breakage calculated by way of Dsieve, DFmax, DFmin, and Deq;
- Dr
- relative density;
- Dsieve, DFmax, DFmin, and Deq
- sieve diameter, maximum Feret diameter, minimum Feret diameter, and equivalent diameter;
- dɛ1 and dɛv
- axial and volumetric strain increment;
- E
- input energy per unit volume;
- E50
- secant modulus corresponding to 50% qf;
- Gs
- specific gravity;
- k
- coefficient of permeability;
- q
- deviator stress;
- qcyc
- maximum cyclic deviator stress;
- qf and q50
- deviator stress at failure and half of qf;
- u
- excess pore water pressure;
- ɛ1 and ɛv
- axial and volumetric strain;
- ɛ50
- axial strain corresponding to q50;
- θ
- depositional angle;
- ρmax/min
- maximum and minimum dry density;
- major effective principal stress;
- minor effective principal stress or confining pressure;
- φmax
- effective peak friction angle; and
- ψmax
- maximum dilation angle.
References
Abelev, A. V., and P. V. Lade. 2003. “Effects of cross anisotropy on three-dimensional behavior of sand I stress–strain behavior and shear banding.” J. Eng. Mech. 129 (2): 160–166.
Alba, J. L., and J. M. Audibert. 1999. “Pile design in calcareous and carbonaceous granular materials, and historic review.” In Proc., 2nd Int. Conf. on Engineering for Calcareous Sediments, 29–44. Rotterdam, Netherlands: AA Balkema.
Altuhafi, F., C. O’Sullivan, and I. Cavarretta. 2013. “Analysis of an image-based method to quantify the size and shape of sand particles.” J. Geotech. Geoenviron. Eng. 139 (8): 1290–1307. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000855.
Altuhafi, F. N., and M. R. Coop. 2011. “Changes to particle characteristics associated with the compression of sands.” Géotechnique 61 (6): 459–471. https://doi.org/10.1680/geot.9.P.114.
Altuhafi, F. N., M. R. Coop, and V. N. Georgiannou. 2016. “Effect of particle shape on the mechanical behavior of natural sands.” J. Geotech. Geoenviron. Eng. 142 (12): 04016071. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001569.
Arthur, J. R. F., K. S. Chua, and T. Dunstan. 1977. “Induced anisotropy in a sand.” Géotechnique 27 (1): 13–30. https://doi.org/10.1680/geot.1977.27.1.13.
Arthur, J. R. F., and B. K. Menzies. 1972. “Inherent anisotropy in a sand.” Géotechnique 22 (1): 115–128. https://doi.org/10.1680/geot.1972.22.1.115.
Arthur, J. R. F., and A. B. Phillips. 1975. “Homogeneous and layered sand in triaxial compression.” Géotechnique 25 (4): 799–815. https://doi.org/10.1680/geot.1975.25.4.799.
ASTM. 2006. Standard test method for permeability of granular soils (constant head). ASTM D2434-68. West Conshohocken, PA: ASTM.
ASTM. 2011a. Standard test method for consolidated drained triaxial compression test for soils. ASTM D7181. West Conshohocken, PA: ASTM.
ASTM. 2011b. Standard test method for consolidated undrained triaxial compression test for soils. ASTM D4767. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test method for specific gravity of soil solids by gas pycnometer. ASTM standard D5550-14. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test methods for maximum index density and unit weight of soils using a vibratory table. ASTM D4253-16. West Conshohocken, PA: ASTM.
ASTM. 2017a. Standard practice for classification of soils for engineering purposes. ASTM D2487. West Conshohocken, PA: ASTM.
ASTM. 2017b. Standard test methods for particle-size distribution (gradation) of soils using sieve analysis. ASTM D6913/D6913M-17. West Conshohocken, PA: ASTM.
Bisht, M. S., and A. Das. 2021. “DEM study on particle shape evolution during crushing of granular materials.” Int. J. Geomech. 21 (7): 04021101. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002067.
Brandes, H. G. 2011. “Simple shear behavior of calcareous and quartz sands.” Geotech. Geol. Eng. 29 (1): 113–126. https://doi.org/10.1007/s10706-010-9357-x.
Casagrande, A., and N. Carrillo. 1944. “Shear failure of anisotropic materials.” Proc. Boston Sot. Civ. Eng. 31: 74–87.
Coop, M. R., K. K. Sorensen, T. B. Freitas, and G. Georgoutsos. 2004. “Particle breakage during shearing of a carbonate sand.” Géotechnique 54 (3): 157–163. https://doi.org/10.1680/geot.2004.54.3.157.
Donohue, S., C. O’Sullivan, and M. Long. 2009. “Particle breakage during cyclic triaxial loading of a carbonate sand.” Géotechnique 59 (5): 477–482. https://doi.org/10.1680/geot.2008.T.003.
Guo, P. 2008. “Modified direct shear test for anisotropic strength of sand.” J. Geotech. Geoenviron. Eng. 134 (9): 1311–1318. https://doi.org/10.1061/(ASCE)1090-0241(2008)134:9(1311).
Hardin, B. O. 1985. “Crushing of soil particles.” J. Geotech. Eng. 111 (10): 1177–1192. https://doi.org/10.1061/(ASCE)07339410(1985)111:10(1177).
Hiramatsu, Y., and Y. Oka. 1966. “Determination of the tensile strength of rock by a compression test of an irregular test piece.” Int. J. Rock Mech. Min. Sci. 3 (2): 89–90. https://doi.org/10.1016/0148-9062(66)90002-7.
Indraratna, B., P. K. Thakur, and J. S. Vinod. 2010. “Experimental and numerical study of railway ballast behavior under cyclic loading.” Int. J. Geomech. 10 (4): 136–144. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000055.
King, R., and M. Lodg. 1988. “North west shelf development the foundation engineering challenge.” In Vol. 2 of Proc., Int. Conf. on Calcareous Sediments, 333–342. Rotterdam, Netherlands: Balkema.
Lade, P. V., and A. V. Abelev. 2003. “Effects of cross anisotropy on three-dimensional behavior of sand. II: Volume change behavior and failure.” J. Eng. Mech. 129 (2): 167–174.
Li, X., J. K. Liu, and J. Z. Li. 2022. “Fractal dimension, particle shape, and particle breakage analysis for calcareous sand.” B. Eng. Geol. Environ. 81 (3): 1–20.
Liu, H., K. Zeng, and Y. Zou. 2020. “Particle breakage of calcareous sand and its correlation with input energy.” Int. J. Geomech. 20 (2): 04019151. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001541.
Luzzani, L., and M. R. Coop. 2002. “On the relationship between particle breakage and the critical state of sands.” Soils Found. 42 (2): 71–82. https://doi.org/10.3208/sandf.42.2_71.
Ma, L., Z. Li, M. Wang, H. Wei, and P. Fan. 2019. “Effects of size and loading rate on the mechanical properties of single coral particles.” Powder Technol. 342: 961–971. https://doi.org/10.1016/j.powtec.2018.10.037.
Miao, G., and D. Airey. 2013. “Breakage and ultimate states for a carbonate sand.” Géotechnique 63 (14): 1221–1229. https://doi.org/10.1680/geot.12.P.111.
Nakata, Y., M. Hyodo, H. Murata, and N. Yasufuku. 1998. “Flow deformation of sands subjected to principal stress rotation.” Soils Found. 38 (2): 115–128. https://doi.org/10.3208/sandf.38.2_115.
Oda, M. 1972. “Initial fabrics and their relations to mechanical properties of granular material.” Soils Found. 12 (1): 17–36. https://doi.org/10.3208/sandf1960.12.17.
Oda, M., I. Koishikawa, and T. Higuchi. 1978. “Experimental study of anisotropic shear strength of sand by plane strain test.” Soils Found. 18 (1): 25–38. https://doi.org/10.3208/sandf1972.18.25.
Oda, M., and H. Nakayama. 1988. “Introduction of inherent anisotropy of soils in the yield function.” Stud. Appl. Mech. 20: 81–90. https://doi.org/10.1016/B978-0-444-70523-5.50017-5.
Razeghi, H. R., and H. M. Romiani. 2015. “Experimental investigation on the inherent and initial induced anisotropy of sand.” KSCE J. Civ. Eng. 19 (3): 583–591. https://doi.org/10.1007/s12205-012-0373-7.
Rui, S., Z. Guo, T. Si, W. Zhou, and X. Zha. 2021. “Particle shape influence on the deformation resistance of carbonate sands under drained condition.” Soil Dyn. Earthquake Eng. 144: 106688. https://doi.org/10.1016/j.soildyn.2021.106688.
Schneider, C. A., W. S. Rasband, and K. W. Eliceiri. 2012. “NIH image to ImageJ: 25 years of image analysis.” Nat. Methods 9: 671–675. https://doi.org/10.1038/nmeth.2089.
Shahnazari, H., and R. Rezvani. 2013. “Effective parameters for the particle breakage of calcareous sands: An experimental study.” Eng. Geol. 159 (12): 98–105. https://doi.org/10.1016/j.enggeo.2013.03.005.
Song, F., J.-M. Zhang, and G.-R. Cao. 2015. “Experimental investigation of asymptotic state for anisotropic sand.” Acta Geotech. 10 (5): 571–585. https://doi.org/10.1007/s11440-014-0357-5.
Tong, Z., P. Fu, S. Zhou, and Y. F. Dafalias. 2014. “Experimental investigation of shear strength of sands with inherent fabric anisotropy.” Acta Geotech. 9 (2): 257–275. https://doi.org/10.1007/s11440-014-0303-6.
Wang, C., H. Liu, X. Ding, C. Wang, and Q. Ou. 2021. “Study on horizontal bearing characteristics of pile foundations in coral sand.” Can. Geotech. J. 58: 1928–1942. https://doi.org/10.1139/cgj-2020-0623.
Wang, X.-Z., Y.-Y. Jiao, R. Wang, M.-J. Hu, Q.-S. Meng, and F.-Y. Tan. 2011. “Engineering characteristics of the calcareous sand in Nansha islands, South China Sea.” Eng. Geol. 120: 40–47. https://doi.org/10.1016/j.enggeo.2011.03.011.
Wei, D., B. Zhao, D. Dias-da-Costa, and Y. Gan. 2019. “An FDEM study of particle breakage under rotational point loading.” Eng. Fract. Mech. 212: 221–237. https://doi.org/10.1016/j.engfracmech.2019.03.036.
Wei, H., T. Zhao, J. He, Q. Meng, and X. Wang. 2018. “Evolution of particle breakage for calcareous sands during ring shear tests.” Int. J. Geomech. 18 (2): 04017153. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001073.
Wu, Y., N. Li, X. Wang, J. Cui, Y. Chen, Y. Wu, and H. Yamamoto. 2021. “Experimental investigation on mechanical behavior and particle crushing of calcareous sand retrieved from South China Sea.” Eng. Geol. 280: 105932. https://doi.org/10.1016/j.enggeo.2020.105932.
Xiao, Y., H. Liu, C. S. Desai, Y. Sun, and H. Liu. 2016. “Effect of intermediate principal-stress ratio on particle breakage of rockfill material.” J. Geotech. Geoenviron. Eng. 142 (4): 06015017. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001433.
Xiao, Y., L. Long, T. M. Evans, H. Zhou, H. Liu, and A. W. Stuedlein. 2019. “Effect of particle shape on stress-dilatancy responses of medium-dense sands.” J. Geotech. Geoenviron. Eng. 145 (2): 04018105. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001994.
Xiao, Y., Y. Sun, W. Zhou, J. Shi, and C. S. Desai. 2022. “Evolution of particle shape produced by sand breakage.” Int. J. Geomech. 22 (4): 04022003. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002333.
Xiong, H., L. Guo, Y. Cai, and Z. Yang. 2016. “Experimental study of drained anisotropy of granular soils involving rotation of principal stress direction.” Eur. J. Environ. Civ. Eng. 20 (4): 431–454. https://doi.org/10.1080/19648189.2015.1039662.
Yamada, Y., and K. Ishihara. 1979. “Anisotropic deformation characteristics of sand under three dimensional stress conditions.” Soils Found. 19 (2): 79–94. https://doi.org/10.3208/sandf1972.19.2_79.
Yang, L.-T., X. Li, H.-S. Yu, and D. Wanatowski. 2016. “A laboratory study of anisotropic geomaterials incorporating recent micromechanical understanding.” Acta Geotech. 11 (5): 1111–1129. https://doi.org/10.1007/s11440-015-0423-7.
Yoshimine, M., K. Ishihara, and W. Vargas. 1998. “Effects of principal stress direction and intermediate principal stress on undrained shear behavior of sand.” Soils Found. 38 (3): 179–188. https://doi.org/10.3208/sandf.38.3_179.
Yu, F. 2017. “Particle breakage and the drained shear behavior of sands.” Int. J. Geomech. 17 (8): 04017041. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000919.
Yu, F. 2018. “Particle breakage in triaxial shear of a coral sand.” Soils Found. 58 (4): 866–880. https://doi.org/10.1016/j.sandf.2018.04.001.
Zhu, F., and J. Zhao. 2021. “Interplays between particle shape and particle breakage in confined continuous crushing of granular media.” Powder Technol. 378: 455–467. https://doi.org/10.1016/j.powtec.2020.10.020.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: May 10, 2022
Accepted: Nov 9, 2022
Published online: Feb 22, 2023
Published in print: May 1, 2023
Discussion open until: Jul 22, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.