Cone Penetrometer with a Helical-Type Outer Screw Rod for Evaluation of the Subgrade Condition
Publication: Journal of Transportation Engineering
Volume 139, Issue 2
Abstract
A weak railway subgrade may lead to instability of the railway track system. The condition of a railway subgrade is typically evaluated using trial pit excavation and a portable ballast sampler, which may severely disturb the ballast layer. Also, nondestructive geophysical techniques, such as ground penetrating radar (GPR), are used to investigate the condition of the ballast and subgrade along the track. The objective of this study is the development and application of a cone penetrometer with a helical-type outer screw rod (CPH) that minimizes the disturbance of the ballast layer for the evaluation of the subgrade condition by measuring the resistance of the cone tip. The CPH consists of a helical-type outer screw rod (helical rod) and a mini cone penetrometer inside the rod. The design concerns include easy installation of the helical rod into the ballast layer, the reaction force of the mini cone penetrometer, installation of the strain gauge, and calculation of the cone tip resistance. The helical rod, which penetrates into the ballast layer with a rotation force, provides the reaction force for the mini cone penetration test. The mini cone penetrometer with a diameter of 15 mm is pushed into the subgrade (sand layer) at the penetration rate of . In addition, dynamic cone penetrometer (DCP) tests are carried out to compare the cone tip resistance with the DCP index (DCPI). Field application tests reveal that the cone tip resistance increases with an increase in the depth and is inversely proportional to the DCPI. On the basis of the cone tip resistance, the soil types of subgrade at three sites are classified as sandy silt to silty sand. This study suggests that the CPH may be a useful device for providing a reliable geotechnical parameter and estimating the subgrade condition with minimal disturbance of the ballast layer.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MEST) (No. 2011-0018110).
References
Abu-Farsakh, M. Y., Alshibli, K., Nazzal, M., and Seyman, E. (2004). Assessment of in-situ test technology for construction control of base courses and embankments, Louisiana Transportation Research Center, Baton Rouge, LA.
Al-Qadi, I. L., Xie, W., Roberts, R., and Leng, Z. (2010). “Data analysis techniques for GPR used for assessing railroad ballast in high radio-frequency environment.” J. Transp. Eng., 136(4), 392–399.
Ampadu, S. I. K., and Arthur, T. D. (2006). “The dynamic cone penetrometer in compaction verification on a model road pavement.” Geotech. Test. J., 29(1), 70–79.
Aw, E. S. (2007). “Low cost monitoring system to diagnose problematic rail bed: Case study at a mud pumping site.” Ph.D. thesis, Massachusetts Institute of Technology, Cambridge, MA.
Ayres, D. J. (1986). “Geotextiles or geomembranes in track? British Railways experience.” Geotext. Geomembr., 3(2–3), 129–142.
Bemben, S. M., and Myers, H. J. (1974). “The influence of rate of penetration on static cone resistance in Connecticut river valley varved clay.” Proc., European Symp. on Penetration Testing, Vol. 2(2), National Swedish Council for Building Research, Stockholm, Swedish, 33–43.
Cho, G. C., Lee, J. S., and Santamarina, J. C. (2004). “Spatial variability in soils: High resolution assessment with electrical needle probe.” J. Geotech. Geoenviron. Eng., 130(8), 843–850.
De Lima, D. C., and Tumay, M. T. (1991). “Scale effects in cone penetration tests.” Proc., Geotechnical Engineering Congress, Vol. 1, ASCE, Boulder, CO, 38–51.
Gallego, I., Munoz, J., Rivas, A., and Sanchez-Cambronero, S. (2011). “Vertical track stiffness as a new parameter involved in designing high-speed railway infrastructure.” J. Transp. Eng., 137(12), 971–979.
Hird, C. C., Johnson, P., and Sills, G. C. (2003). “Performance of miniature piezocones in thinly layered soils.” Geotechnique, 53(10), 885–900.
Hird, C. C., and Springman, S. M. (2006). “Comparative performance of 5cm2 and 10cm2 piezocones in a lacustrine clay.” Geotechnique, 56(6), 427–438.
Joh, S. H., Hwang, S. K., and Nayan, K. A. M. (2011). “Real-time spatial profiling of subgrade stiffness for quality assurance of field compaction.” 90th Annual Meeting of the Transportation Research Board, TRB, Washington, DC.
Kim, D. S., Hwang, S. K., Shin, M. H., and Park, T. S. (2005). “Evaluation on the condition of track substructure using GPR/PBS/LFWD.” J. Korea Geotech. Soc., 21(5), 163–170.
Kim, R., Lee, W., and Lee, J. S. (2010). “Temperature-compensated cone penetration test mini-cone using fiber optic sensors.” Geotech. Test. J., 33(3), 243–252.
Lee, W., Shin, D. H., Yoon, H. K., and Lee, J. S. (2009). “Micro-cone penetrometer for more concise subsurface layer detection.” Geotech. Test. J., 32(4), 358–364.
Lunne, T., Robertson, P. K., and Powell, J. J. M. (1997). Cone penetration testing in geotechnical practice, Blakie Academic, London.
Mohammadi, S. D., Nikoudel, M. R., Rahimi, H., and Khamehchiyan, M. (2008). “Application of the dynamic cone penetrometer (DCP) for determination of the engineering parameters of sandy soils.” Eng. Geol., 101(3–4), 195–203.
Powell, J. J. M., and Quarterman, R. S. T. (1988). “Interpretation of cone penetration tests in clays, with particular reference to rate effects.” Proc., 1st Int. Symp. on Penetration, Vol. 2, Balkema, Rotterdam, 903–909.
Robertson, P. K., Campanella, R. G., Gillespie, D., and Greig, J. (1986). “Use of piezometer cone data.” Proc., ASCE Specialty Conf. In Situ ’86: Use of In Situ Tests in Geotechnical Engineering, ASCE, Reston, VA, 1263–1280.
Salgado, R., and Yoon, S. (2003). “Dynamic cone penetration test (DCPT) for subgrade assessment.” Joint Transportation Research Program Technical Report Series, Purdue Univ., West Lafayette, IN.
Shin, D. H., Lee, C., Lee, J. S., and Lee, W. (2009). “Detection of smear zone using micro-cone and electrical resistance probe.” Can. Geotech. J., 46(6), 719–726.
Siekmeier, J. A., Young, D., and Beberg, D. (1999). “Comparison of the dynamic cone penetrometer with other tests during subgrade and granular base characterization in Minnesota.” Nondestructive testing of pavements and backcalculation of moduli, Vol. 3, ASTM, West Conshohocken, PA.
Sussmann, T. R., Selig, E. T., and Hyslip, J. P. (2003). “Railway track condition indicators from ground penetrating radar.” NDT&E Int., 36(3), 157–167.
Tumay, M. T., and Kurup, P. U. (2001). “Development of a continuous intrusion miniature cone penetration test system for subsurface explorations.” Soils Found., 41(6), 129–138.
Yoon, H. K., Jung, S. H., and Lee, J. S. (2011). “Characterisation of subsurface spatial variability using a cone resistivity penetrometer.” Soil Dyn. Earthquake Eng., 31(7), 1064–1071.
Yoon, H. K., and Lee, J. S. (2012). “Microcones configured with full-bridge circuits.” Soil Dyn. Earthquake Eng., 41, 119–127.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Feb 10, 2012
Accepted: Sep 19, 2012
Published online: Sep 22, 2012
Published in print: Feb 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.