Nondestructive Assessment of Elastomeric Bridge Bearings Using 3D Digital Image Correlation
Publication: Journal of Structural Engineering
Volume 148, Issue 1
Abstract
Elastomeric bridge bearings are installed between the bridge superstructure and substructure to accommodate translational and rotational deformations. The manufacturing quality of elastomeric bridge bearings is of high significance because manufacturing defects (such as variations in rubber layer thickness and nonparallel steel laminates) may jeopardize their short- and long-term structural behavior and integrity. Current quality control procedures involve destructive testing of samples of bearings from a lot. This type of testing is time consuming and costly, and thus limited to a relatively small sample size, which may undermine confidence in the quality of remaining bearings in the lot. This paper presents an alternative, vision-based assessment methodology for the nondestructive identification of the internal structure of elastomeric bridge bearings. The methodology capitalizes on the high deformability of rubber and the near inextensibility of the steel laminates, which together result in a unique deformation pattern on the vertical surfaces of a bearing when it is subjected to axial load. This deformation pattern features local extrema in in-plane strain and horizontal displacement fields on the vertical surfaces. These local extrema are analyzed to deduce the thicknesses of the rubber layers and rubber side covers. The methodology is developed based on three-dimensional finite-element analyses (3D-FEA). Then, three-dimensional digital image correlation (3D-DIC) is used in experimental tests to evaluate its capability to identify manufacturing defects in elastomeric bridge bearings. Finally, the methodology is validated against destructive tests. The nondestructive method presented in this study is conducted in conjunction with compressive tests that departments of transportation carry out routinely and is therefore expected to facilitate rapid and cost-effective qualification of elastomeric bridge bearings.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This research was supported by the Ministry of Transportation of Ontario (MTO) through the Highway Infrastructure Innovation Funding Program (HIIFP), Award No. 9017-R-0022. The authors are grateful to Kris Mermigas, Head Engineer, Bridge Design Office, MTO, and Jennifer Astle-Tranmer, Senior Materials Officer, Materials Engineering & Research Office, MTO, for their committed support during this work. Any opinions, findings, and conclusions or recommendations expressed in this paper are those of the authors and do not necessarily reflect the views of the sponsor.
References
AASHTO. 2018. Standard specification for plain and laminated elastomeric bridge bearings. Washington, DC: AASHTO.
Ahmadi Soleimani, S., D. Konstantinidis, and G. P. Balomenos. 2020. “Vision-based quality control testing of elastomeric bridge bearings.” In Proc., Structures Congress, 651–664. Reston, VA: ASCE.
Belivanis, K. V. 2017. “Expanding the use of elastomeric bearings for higher demand applications.” Ph.D. thesis, Dept. of Civil, Architectural and Environmental Engineering, Univ. of Texas at Austin.
Birolini, A. 2013. Reliability engineering: Theory and practice. Berlin: Springer.
Bolhassani, M., S. Rajaram, A. A. Hamid, A. Kontsos, and I. Bartoli. 2016. “Damage detection of concrete masonry structures by enhancing deformation measurement using DIC.” In Proc., Nondestructive Characterization and Monitoring of Advanced Materials, Aerospace, and Civil Infrastructure 2016, 980411. Las Vegas, Nevada: International Society for Optics and Photonics.
Born, M., and E. Wolf. 1965. Principles of optics, 3rd ed. London: Pergamon Press Ltd.
CEN (European Commission for Standardization). 2005. Structural bearings—Part 3: Elastomeric bearings. Brussels, Belgium: CEN.
Chen, Z., C. Quan, F. Zhu, and X. He. 2015. “A method to transfer speckle patterns for digital image correlation.” Meas. Sci. Technol. 26 (9): 1–10. https://doi.org/10.1088/0957-0233/26/9/095201.
Dassault Systemes. 2019. ABAQUS 2019 theory manual. Providence, Rhode Island: Dassault Systemes Simulia Corp.
De Wilder, K., G. De Roeck, and L. Vandewalle. 2016. “The use of advanced optical measurement methods for the mechanical analysis of shear deficient prestressed concrete members.” Int. J. Concr. Struct. Mater. 10 (2): 189–203. https://doi.org/10.1007/s40069-016-0135-x.
Doyle, J. F. 2004. Modern experimental stress analysis: Completing the solution of partially specified problems. Chichester, UK: Wiley.
Dutton, M., W. A. Take, and N. A. Hoult. 2014. “Curvature monitoring of beams using digital image correlation.” J. Bridge Eng. 19 (3): 1–13. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000538.
Fastec Imaging. 2014. Fastec FasMotion controller software. San Diego: Fastec Imaging.
Forni, M., A. Martelli, and A. Dusi. 1999. Implementation and validation of hyperelastic finite element models of high damping rubber bearings.” In Proc., Constitutive models for rubber, 237–247. Rotterdam, Netherlands: A. A. Balkema.
Freddi, A., G. Olmi, and L. Cristofolini. 2015. Experimental stress analysis for materials and structures. New York: Springer.
Ghorbani, R., F. Matta, and M. A. Sutton. 2015. “Full-field deformation measurement and crack mapping on confined masonry walls using digital image correlation.” Exp. Mech. 55 (1): 227–243. https://doi.org/10.1007/s11340-014-9906-y.
GOM. 2018. GOM correlate professional software. Braunschweig, Germany: GOM.
Grediac, M. 2004. “The use of full-field measurement methods in composite material characterization: Interest and limitations.” Composites, Part A 35 (7–8): 751–761. https://doi.org/10.1016/j.compositesa.2004.01.019.
Hartley, R. I., and P. Sturm. 1997. “Triangulation.” Comput. Vision Image Understanding 68 (2): 146–157. https://doi.org/10.1006/cviu.1997.0547.
Iadicola, M. A. 2012. Digital image correlation measurements during gusset plate connection testing to structural failure. Gaithersburg, MD: NIST.
IO Industries. 2016. DVR express CoreView. London: IO Industries.
Kelly, J. M., and D. Konstantinidis. 2009. “Effect of friction on unbonded elastomeric bearings.” J. Eng. Mech. 135 (9): 953–960. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000019.
Kelly, J. M., and D. Konstantinidis. 2011. Mechanics of rubber bearings for seismic and vibration isolation. Chichester, UK: Wiley.
Kelly, J. M., and N. C. Van Engelen. 2015. Single series solution for the rectangular fiber-reinforced elastomeric isolator compression modulus. Berkeley, CA: Univ. of California.
Konstantinidis, D., J. M. Kelly, and N. Makris. 2008. Experimental investigation on the seismic response of bridge bearings. Berkeley, CA: Univ. of California.
Konstantinidis, D., and S. R. Moghadam. 2016. “Compression of unbonded rubber layers taking into account bulk compressibility and contact slip at the supports.” Int. J. Solids Struct. 87 (Jun): 206–221. https://doi.org/10.1016/j.ijsolstr.2016.02.008.
Lane, C., R. L. Burguete, and A. Shterenlikht. 2008. “An objective criterion for the selection of an optimum DIC pattern and subset size.” In Proc., 11th Int. Congress and Exposition, 1–9. Bethel, CT: Society for Experimental Mechanics.
Mayinger, F. 2013. Optical measurements: Techniques and applications. New York: Springer.
McGinnis, M. J., B. Smith, M. Holloman, M. Lisk, A. O’Donnell, and Y. C. Kurama. 2012. “3-D digital image correlation—An underused asset for structural testing.” In Proc., Structures Congress, 1958–1969. Reston, VA: ASCE.
Moghadam, S. R., and D. Konstantinidis. 2017. “Finite element study of the effect of support rotation on the horizontal behavior of elastomeric bearings.” Compos. Struct. 163 (Mar): 474–490. https://doi.org/10.1016/j.compstruct.2016.12.013.
Mojsilović, N., and A. H. Salmanpour. 2016. “Masonry walls subjected to in-plane cyclic loading: Application of digital image correlation for deformation field measurement.” Int. J. Masonry Res. Innov. 1 (2): 165–187. https://doi.org/10.1504/IJMRI.2016.077473.
Muscarella, J. V., and J. Yura. 1995. “An experimental study of elastomeric bridge bearings with design recommendations.” Ph.D. thesis, Center for Transportation Research, Univ. of Texas at Austin.
OPSS (Ontario Provincial Standard Specification). 2017. Material specification for bearings—Elastomeric plain and steel laminated. Toronto, ON: OPSS.
Orteu, J.-J. 2009. “3-D computer vision in experimental mechanics.” Opt. Lasers Eng. 47 (3–4): 282–291. https://doi.org/10.1016/j.optlaseng.2007.11.009.
Osgooei, P. M., M. J. Tait, and D. Konstantinidis. 2014. “Three-dimensional finite element analysis of circular fiber-reinforced elastomeric bearings under compression.” Compos. Struct. 108 (Feb): 191–204. https://doi.org/10.1016/j.compstruct.2013.09.008.
Pan, B., K. Qian, H. Xie, and A. Asundi. 2009. “Two-dimensional digital image correlation for in-plane displacement and strain measurement: A review.” Meas. Sci. Technol. 20 (6): 062001. https://doi.org/10.1088/0957-0233/20/6/062001.
Roeder, C. W., J. F. Stanton, and T. Feller. 1989. Low temperature behavior and acceptance criteria for elastomeric bridge bearings. Washington, DC: Transportation Research Board.
Sieffert, Y., F. Vieux-Champagne, S. Grange, P. Garnier, J. Duccini, and L. Daudeville. 2016. “Full-field measurement with a digital image correlation analysis of a shake table test on a timber-framed structure filled with stones and earth.” Eng. Struct. 123 (Sep): 451–472. https://doi.org/10.1016/j.engstruct.2016.06.009.
Sokoli, D., W. Shekarchi, E. Buenrostro, and W. M. Ghannoum. 2014. “Advancing behavioral understanding and damage evaluation of concrete members using high-resolution digital image correlation data.” Earthquakes Struct. 7 (5): 609–626. https://doi.org/10.12989/eas.2014.7.5.609.
Stanton, J. F., C. W. Roeder, P. Mackenzie-Helnwein, C. White, C. Kuester, and B. Craig. 2008. Rotation limits for elastomeric bearings. Washington, DC: Transportation Research Board.
Sun, C. 2015. “Material study of the steel reinforced elastomeric bridge bearings.” Ph.D. thesis, Dept. of Civil, Architectural and Environmental Engineering, Univ. of Texas at Austin.
Sutton, M., W. Wolters, W. Peters, W. Ranson, and S. McNeill. 1983. “Determination of displacements using an improved digital correlation method.” Image Vision Comput. 1 (3): 133–139. https://doi.org/10.1016/0262-8856(83)90064-1.
Sutton, M. A. 2013. “Computer vision-based, noncontacting deformation measurements in mechanics: A generational transformation.” Appl. Mech. Rev. 65 (5): 050802. https://doi.org/10.1115/1.4024984.
Sutton, M. A., H. Schreier, and J.-J. Orteu. 2009. Image correlation for shape, motion and deformation measurements. New York: Springer.
Triggs, B., P. F. McLauchlan, R. Hartley, and A. W. Fitzgibbon. 1999. “Bundle adjustment—A modern synthesis.” In International workshop on vision algorithms, 298–372. Berlin: Springer.
Yakut, A., and J. A. Yura. 2002. “Parameters influencing performance of elastomeric bearings at low temperatures.” J. Struct. Eng. 128 (8): 986–994. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:8(986).
Yeoh, O. H. 1993. “Some forms of the strain energy function for rubber.” Rubber Chem. Technol. 66 (5): 754–771. https://doi.org/10.5254/1.3538343.
Yura, J., A. Kumar, A. Yakut, C. Topkaya, E. Becker, and J. Collingwood. 2001. Elastomeric bridge bearings: Recommended test methods. Washington, DC: Transportation Research Board.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Dec 8, 2020
Accepted: Aug 2, 2021
Published online: Oct 21, 2021
Published in print: Jan 1, 2022
Discussion open until: Mar 21, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Saleh Ahmadi Soleimani, Dimitrios Konstantinidis, Georgios P. Balomenos, Effect of Manufacturing Imperfections on the Service-Level Performance of Elastomeric Bridge Bearings, Journal of Structural Engineering, 10.1061/(ASCE)ST.1943-541X.0003365, 148, 7, (2022).