Tightening Procedures for Proper Installation of Anchor Rods in Ancillary Structures
Publication: Journal of Structural Engineering
Volume 147, Issue 10
Abstract
In the last 2 decades, many ancillary structures have collapsed, with several instances traceable to loose anchor nuts. According to a quality assurance inspection conducted by the Virginia Department of Transportation (VDOT) in 2012, approximately 30% of the anchor nuts on the inspected ancillary structures across the state of Virginia were found to be loose. The exact cause of the loose anchor nuts is not known; however, one theory is that specified tightening procedures were not properly followed or were not adequate. Currently, a turn-of-the-nut method is used for the tightening of anchor nuts on double-nut moment connections at the base of ancillary structures. This research reviewed current tightening procedures for anchor nuts on ancillary structures. The relationship between three critical tightening parameters—applied torque, nut rotation, and pretension in the rod—was examined. One hundred galvanized steel anchor rods of five different diameters and three different grades were tested. The experimental tests serve as a benchmark to validate the current tightening procedures, as well as to recommend changes.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code generated or used during the study are available from the corresponding author by request, including incremental tightening data for nut rotations, measured pretension (strain gauge), and applied torque.
Acknowledgments
The research work reported herein was supported and funded by the Virginia Transportation Research Council (VTRC).
References
AASHTO. 2015. LRFD specifications for structural supports for highway signs, luminaires, and traffic signals. Washington, DC: AASHTO.
ASTM. 2014a. Standard specification for aluminum and aluminum-alloy sheet and plate. ASTM B209-14. West Conshohocken, PA: ASTM.
ASTM. 2014b. Standard specification for carbon structural steel. ASTM A36/A36M-14. West Conshohocken, PA: ASTM.
ASTM. 2015a. Standard specification for anchor bolts, steel, 36, 55, and 105-ksi yield strength. ASTM F1554-15. West Conshohocken, PA: ASTM.
ASTM. 2015b. Standard specification for carbon and alloy steel nuts. ASTM A563-15. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard specification for carbon steel, alloy steel, and stainless steel nuts for bolts for high pressure or high temperature service, or both. ASTM A194/A194M-16a. West Conshohocken, PA: ASTM.
ASTM. 2018a. Standard specification for aluminum-alloy sand castings. ASTM B26/B26M-18. West Conshohocken, PA: ASTM.
ASTM. 2018b. Standard specification for hardened steel washers inch and metric dimensions. ASTM F436/F436M-18a. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard specification for high strength structural bolts and assemblies, steel and alloy steel, heat treated, inch dimensions 120 ksi and 150 ksi minimum tensile strength, and metric dimensions 830 MPa and 1,040 MPa minimum tensile strength. ASTM F3125/F3125M-19e2. West Conshohocken, PA: ASTM.
Bickford, J. H. 2008. Introduction to the design and behavior of bolted joints. Boca Raton, FL: CRC Press.
Chen, A., C. Schaeffer, Y. Zhang, B. Phares, B. Shafei, M. Yang, Z. Lin, and S. Paudel. 2018. Re-tightening the large anchor bolts of support structures for signs and luminaires. St. Paul, MN: Minnesota DOT.
Dexter, R. J., and M. J. Ricker. 2002. Fatigue-resistant design of cantilevered signal, sign, and light supports. Washington, DC: National Academies Press.
Garlich, M. J., and J. W. Koonce. 2011. “Anchor rod tightening for highmast light towers and cantilever sign structures.” In Proc., 90th Annual Meeting of the Transportation Research Board. Washington, DC: Transportation Research Board.
Garlich, M. J., and E. T. Thorkildsen. 2005. Guidelines for the installation, inspection, maintenance and repair of structural supports for highway signs, luminaires, and traffic signals. Washington, DC: Federal Highway Administration.
Hoisington, D., and S. Hamel. 2016. “Evaluating the behavior of anchor rod foundations for high-mast light poles using nonlinear finite-element analysis.” J. Struct. Eng. 142 (9): 04016047. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001495.
Hoisington, D., J. Hoffman, and S. Hamel. 2014. “Measured anchor rod tightening of high-mast light poles in Alaska.” Transp. Res. Rec. 2431 (1): 67–72. https://doi.org/10.3141/2431-09.
James, R. W., P. B. Keating, R. W. Bolton, F. C. Benson, D. E. Bray, R. C. Abraham, and J. B. Hodge. 1997. Tightening procedures for large-diameter anchor bolts. Austin, TX: Texas DOT.
Johns, K. W., and R. J. Dexter. 1998. Fatigue related wind loads on highway support structures. Bethlehem, PA: Lehigh Univ.
Kaczinski, M. R., R. J. Dexter, and J. P. Van Dien. 1998. Fatigue-resistant design of cantilevered signal, sign and light supports. Washington, DC: National Academies Press.
RCSC (Research Council on Structural Connections). 2014. Specifications for assembly of structural joints using high tensile steel bolts. Chicago: AISC.
Richards, J. H. 2004. “Turn-of-the-nut tightening of anchor bolts.” M.Sc. thesis, Dept. of Civil and Environmental Engineering, Texas A&M Univ.
Till, R. D., and N. A. Lefke. 1994. The relationship between torque, tension, and nut rotation of large diameter anchor bolts. Lansing, MI: Michigan DOT.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Sep 30, 2019
Accepted: Apr 19, 2021
Published online: Jul 20, 2021
Published in print: Oct 1, 2021
Discussion open until: Dec 20, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.