Generalized Load Deformation Relationship for Bearing-Type Single-Bolted Connections
Publication: Journal of Structural Engineering
Volume 146, Issue 7
Abstract
The bearing boundary conditions in bolted connections can be classified either as open. when end tear-out is possible, or as closed, when end tear-out is physically impossible. In this study, comprehensive tests of single-bolted bearing connections were conducted and analyzed considering the two bearing boundary conditions. The primary objective was to develop a generalized load–deformation relationship that can be used when designing group-bolted connections based on the instantaneous center of rotation method (ICRM). A new bearing-strength formula, permissible deformation limits, and new load–deformation relationship covering high-strength steel were proposed.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
The data of this study are available from the corresponding author on request.
Acknowledgments
This research was supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (Grant No. 0415-20140028).
References
AISC. 1994. Manual of steel construction, load and resistance factor design. Chicago: AISC.
AISC. 2016. Specification for structural steel buildings. AISC 360. Chicago: AISC.
Crawford, S. F., and G. L. Kulak. 1968. Behavior of eccentrically loaded bolted connections: Studies in structural engineering no. 4. Halifax, NS: Nova Scotia Technical College.
Crawford, S. F., and G. L. Kulak. 1971. “Eccentrically loaded bolted connections.” J. Struct. Div. 97 (3): 765–783.
de Back, J., and A. de Jong. 1968. Measurements on connections with high strength bolts, particularly in view of the permissible arithmetical bearing stress. Delft, Netherlands: Delft Univ. of Technology.
Fisher, J. W. 1965. On the behavior of fasteners and plates with holes: Fritz engineering laboratory report no. 288.18. Bethlehem, PA: Lehigh Univ.
Frank, K. H., and J. A. Yura. 1981. An experimental study of bolted shear connections. Washington, DC: USDOT.
Hirano, M. 1970. “Bearing stresses in bolted joints.” In Vol. 6 of Society of steel construction of Japan. Tokyo: Society of Steel Construction of Japan.
Jones, J. 1958. “Bearing-ratio effect on strength of riveted joints.” J. Struct. Div. 82 (6): 1–10.
JSA (Japanese Standards Association). 2013. Sets of high strength hexagon bolt, hexagon nut and plain washers for friction grip joints. JIS B 1186. Tokyo: JSA.
Kim, D. K., C. H. Lee, and S. H. Jin. 2015. “Prediction of hysteretic response of group-bolted connections subjected to cyclic eccentric shear loading.” In Proc., 8th Int. Symp. on Steel Structures. Jeju, Korea: Korean Society of Steel Construction.
KSA (Korean Standards Association). 2009. Set of high strength hexagon bolt, hexagon nut and plain washers for friction grip joints. KS B 1010. Seoul: KSA.
Kulak, G. L., J. W. Fisher, and J. H. A. Struik. 2001. Guide to design criteria for bolted and riveted joints. 2nd ed. Chicago: AISC.
Manuel, T. J., and G. L. Kulak. 1998. Strength of joints that combine bolts and welds: Structural engineering report no. 222. Edmonton, Canada: Univ. of Alberta.
Munse, W. H. 1959. The effect of bearing pressure on the static strength of riveted connections: Bulletin 454 engineering experiment station. Champaign, IL: Univ. of Illinois at Urbana-Champaign.
Rex, C. O., and W. S. Easterling. 2003. “Behavior and modeling of a bolt bearing on a single plate.” J. Struct. Eng. 129 (6): 792–800. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:6(792).
Sato, A., and C. M. Uang. 2008. “Seismic design procedure development for cold-formed steel-special bolted moment frames.” J. Constr. Steel Res. 65 (4): 860–868. https://doi.org/10.1016/j.jcsr.2008.03.016.
Sato, A., and C. M. Uang. 2010. “Seismic performance factors for cold-formed steel special bolted moment frame.” J. Struct. Eng. 136 (8): 961–967. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000191.
Teh, L. H., and M. E. Uz. 2017. “Ultimate tilt-bearing capacity of bolted connections in cold-reduced steel sheets.” J. Struct. Eng. 143 (4): 04016206. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001702.
Wang, Y. B., Y. F. Lyu, G. Q. Li, and J. Y. R. Liew. 2017. “Behavior of single bolt bearing on high strength steel plate.” J. Constr. Steel Res. 137 (Oct): 19–30. https://doi.org/10.1016/j.jcsr.2017.06.001.
Yura, J. A., and K. H. Frank. 1994. “Minutes of the June 3.” In Proc., Meeting of the Research Council on Structural Connections. Chicago: Research Council on Structural Connections.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Jul 14, 2019
Accepted: Nov 8, 2019
Published online: Apr 20, 2020
Published in print: Jul 1, 2020
Discussion open until: Sep 20, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.