Effect of Temperature on the Response of Unbonded Fiber-Reinforced Elastomeric Isolators
Publication: Journal of Structural Engineering
Volume 145, Issue 11
Abstract
One of the most commonly used types of isolator is the steel-reinforced elastomeric isolator (SREI), but recent research has been completed on the use of fibers as a replacement to the steel reinforcement layers, reducing weight and potentially costs associated with isolation systems. These fiber-reinforced elastomeric isolators (FREI) can be used in bridges in an unbonded application, where they are placed between the bridge deck and bent cap beams. The use of isolators with bridges requires that the isolators are able to withstand the same negative temperatures that bridges located in cold climates will experience. This study investigates the behavior of unbonded fiber-reinforced elastomeric isolators (U-FREI) subjected to low temperature conditioning, representative of conditions that can be experienced in various regions throughout Canada. The response under lateral deformations expected during seismic events and vertical and rotational loading expected during regular operation were evaluated. The experimental results, in terms of effective stiffness and energy dissipated, indicate that the influence of temperature on the lateral, vertical, and rotational response of U-FREI is acceptable.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was completed as part of the mandate of the Centre for Effective Design of Structures (CEDS) at McMaster University and is partially funded by the Ontario Ministry of Economic Development and Innovation and by the Natural Sciences and Engineering Research Council of Canada (NSERC).
References
AASHTO. 2012. LRFD bridge design specifications. Washington, DC: AASHTO.
AASHTO. 2016. Standard specification for plain and laminated elastomeric bridge bearings. AASHTO M251. Washington, DC: AASHTO.
Al-Anany, Y. M., and M. J. Tait. 2015. “A numerical study on the compressive and rotational behaviour of fiber reinforced elastomeric isolators (FREI).” Compos. Struct. 133 (1): 1249–1266. https://doi.org/10.1016/j.compstruct.2015.07.042.
Al-Anany, Y. M., and M. J. Tait. 2017a. “Experimental assessment of utilizing fiber reinforced elastomeric isolators as bearings for bridge applications.” Composites Part B 114 (1): 373–385. https://doi.org/10.1016/j.compositesb.2017.01.060.
Al-Anany, Y. M., and M. J. Tait. 2017b. “Fiber reinforced elastomeric isolators for the seismic isolation of bridges.” Compos. Struct. 160 (Jan): 300–311. https://doi.org/10.1016/j.compstruct.2016.10.008.
Al-Anany, Y. M., N. C. Van Engelen, and M. J. Tait. 2017. “Vertical and lateral behavior of unbonded fiber-reinforced elastomeric isolators.” Compos. Constr. 21 (5): 04017019. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000794.
ASCE. 2013. Minimum design loads for buildings and other structures. ASCE/SEI 7-10. New York: ASCE.
Bukhina, M. F., and S. K. Kurlyand. 2007. New concepts in polymer science: Low-temperature behaviour of elastomers. Boca Raton, FL: CRC Press.
Cardone, D., and G. Gesualdi. 2012. “Experimental evaluation of the mechanical behavior of elastomeric materials for seismic applications at different air temperatures.” Int. J. Mech. Sci. 64 (1): 127–143. https://doi.org/10.1016/j.ijmecsci.2012.07.008.
Coe, D. G., and P. G. Howgate. 1986. “Effect on crystallization of low frequency shear strain.” In Proc., Int. Rubber Conf. (IRC 86). Goteborg, Sweden: Swedish Institution of Rubber Technology.
Constantinou, M. C., A. S. Whittaker, Y. Kalpakidis, D. M. Fenz, and G. P. Warn. 2007. Performance of seismic isolation hardware under service and seismic loading. Buffalo, NY: Multidisciplinary Center for Earthquake Engineering Research.
CSA (Canadian Standard Association). 2014. Canadian highway bridge design code (CHBDC). CAN/CSA-S6. Rexdale, ON: CSA.
de Raaf, M. G. P., M. J. Tait, and H. Toopchi-Nezhad. 2010. “Stability of fiber-reinforced elastomeric bearings in an unbonded application.” Compos. Mater. 45 (18): 1873–1884. https://doi.org/10.1177/0021998310388319.
Fuller, K. N. G., J. Gough, and A. G. Thomas. 2004. “The effect of low-temperature crystallization on the mechanical behavior of rubber.” Polym. Sci. Part B: Polym. Phys. 42 (11): 2181–2190. https://doi.org/10.1002/polb.20091.
Harris, H. G., and G. M. Sabnis. 1999. Structural modeling and experimental techniques. New York: CRC Press.
ISO. 2010. Elastomeric seismic-protection isolators. ISO 22762-1. Geneva: ISO.
Kelly, J. M. 1999. “Analysis of fiber-reinforced elastomeric isolators.” Seismolog. Earthquake Eng. 2 (1): 19–34.
Kelly, J. M. 2008. “Analysis of the run-in effect in fiber-reinforced isolators under vertical load.” Mech. Mater. Struct. 3 (7): 1383–1401. https://doi.org/10.2140/jomms.2008.3.1383.
Kulak, R. F., and T. H. Hughes. 1993. “Frequency and temperature dependence of high damping elastomers.” In Proc., 12th Biennial Conf. of the Int. Association on Structural Mechanics in Reactor Technology. Washington, DC: USDOE.
Murray, R. M., and J. D. Detenber. 1961. “First and second order transitions in neoprene.” Rubber Chem. Technol. 34 (2): 668–685. https://doi.org/10.5254/1.3540237.
OPSS (Ontario Provincial Standard Specification). 2016. Material specification for bearings: Elastomeric plain and steel laminated. OPSS.MUNI 1202. Ontario, Canada: OPSS.
Pinarbasi, S., U. Akyuz, and G. Ozdemir. 2007. “An experimental study on low temperature behavior of elastomeric bridge bearings.” In Proc., 10th World Conf. on Seismic Isolation, Energy Dissipation and Active Vibrations Control of Structures. Ankara, Turkey: Middle East Technical Univ., Earthquake Engineering Research Center.
Roeder, C. W., J. Stanton, and T. Feller. 1989. Low temperature behavior and acceptance criteria for elastomeric bridge bearings. Washington, DC: National Cooperative Highway Research Program, Transportation Research Board.
Russell, E. W. 1951. “The crystallization of vulcanized natural rubber at low temperatures.” Trans. Faraday Soc. 47: 539–552. https://doi.org/10.1039/tf9514700539.
Sciascetti, A. N., Y. M. Al-Anany, and M. J. Tait. 2016. “The effect of temperature on the lateral response of unbonded fiber-reinforced elastomeric isolators.” In Proc., Canadian Society for Civil Engineering Annual Conf. on Resilient Infrastructure, 1–10. Montreal: Canadian Society for Civil Engineering.
Stevenson, A., and D. L. Maxwell. 1986. “Low temperature stiffening of structural rubber bearings.” In Proc., Int. Rubber Conf. (IRC 86). Goteborg, Sweden: Swedish Institution of Rubber Technology.
Toopchi-Nezhad, H., R. G. Drysdale, and M. J. Tait. 2009. “Parametric study on the response of stable unbonded-fiber reinforced elastomeric isolators (SU-FREIs).” Compos. Mater. 43 (15): 1569–1587. https://doi.org/10.1177/0021998308106322.
Toopchi-Nezhad, H., M. J. Tait, and R. G. Drysdale. 2008a. “Lateral response evaluation of fiber-reinforced neoprene seismic isolators utilized in an unbonded application.” Struct. Eng. 134 (10): 1627–1637. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:10(1627).
Toopchi-Nezhad, H., M. J. Tait, and R. G. Drysdale. 2008b. “A novel elastomeric base isolation system for seismic mitigation of low-rise buildings.” In Proc., 14th World Conf. on Earthquake Engineering. Tokyo: International Associate for Earthquake Engineering.
Toopchi-Nezhad, H., M. J. Tait, and R. G. Drysdale. 2008c. “Testing and modeling of square carbon fiber-reinforced elastomeric seismic isolators.” Struct. Control Health Monit. 15 (6): 876–900. https://doi.org/10.1002/stc.225.
Van Engelen, N. C., P. M. Osgooei, M. J. Tait, and D. Konstantinidis. 2014a. “Experimental and finite element study on the compression properties of modified rectangular fiber-reinforced elastomeric isolators.” Eng. Struct. 74: 52–64. https://doi.org/10.1016/j.engstruct.2014.04.046.
Van Engelen, N. C., M. J. Tait, and D. Konstantinidis. 2014b. “Model of the shear behavior of unbonded fiber-reinforced elastomeric isolators.” Struct. Eng. 141 (7): 04014169. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001120.
Yakut, A., and J. A. Yura. 2002. “Parameters influencing performance of elastomeric bearings at low temperatures.” Struct. Eng. 128 (8): 986–994. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:8(986).
Yura, J., A. Kumar, A. Yakut, C. Topkaya, E. Becker, and J. Collingwood. 2001. Elastomeric bridge bearings: Recommended test methods. Washington, DC: National Cooperative Highway Research Program, Transportation Research Board.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jun 11, 2018
Accepted: Mar 4, 2019
Published online: Aug 27, 2019
Published in print: Nov 1, 2019
Discussion open until: Jan 27, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.