Compression Tests of Cold-Formed Steel C- and Z-Sections with Different Stiffeners
Publication: Journal of Structural Engineering
Volume 145, Issue 5
Abstract
This paper describes an experimental investigation of stub column tests of cold-formed steel C- and Z-sections with different stiffeners. The experimental program consisted of 30 fixed-ended column tests of 6 series of C-sections and 4 series of Z-sections. The configurations of stiffeners comprised simple edge stiffeners, simple lips with inward or outward return lips, and intermediate web stiffeners. The specimens were brake-pressed from high-strength zinc-coated grades G450 and G550 structural steel sheets. The material properties were measured through tensile coupon tests. The load-carrying capacities, load-end shortening responses, and failure modes of stub column specimens are presented and discussed in this paper. The test strengths and observed failure modes were compared with the design strengths and failure modes predicted by the Direct Strength Method. The comparison showed that the Direct Strength Method provides accurate and reliable design strength predictions for C- and Z-sections with different edge stiffeners but provides less accurate design strength predictions for C-sections with intermediate web stiffeners.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful to BHP Steel Building Products for supplying the test specimens.
References
AISI (American Iron and Steel Institute). 2016. North American specification for the design of cold-formed steel structural members. AISI S100. Washington, DC: AISI.
ASCE. 2010. Minimum design loads for buildings and other structures. ASCE/SEI 7. Reston, VA: ASCE.
AS/NZS (Australia/New Zealand Standard). 2005. Cold-formed steel structure. AS/NZS 4600. Sydney, Australia: AS/NZS.
Camotim, D., P. B. Dinis, A. D. Martins, and B. Young. 2018. “Interactive behaviour, failure and DSM design of cold-formed steel members prone to distortional buckling.” Thin Walled Struct. 128: 12–42. https://doi.org/10.1016/j.tws.2017.07.011.
Chen, J., Y. He, and W. L. Jin. 2010. “Stub column tests of thin-walled complex section with intermediate stiffeners.” Thin Walled Struct. 48 (6): 423–429. https://doi.org/10.1016/j.tws.2010.01.008.
Chen, M. T., and B. Young. 2018. “Cross-sectional behavior of cold-formed steel semi-oval hollow sections.” Eng. Struct. 177: 318–330. https://doi.org/10.1016/j.engstruct.2018.08.057.
Chen, M. T., and B. Young. 2019. “Material properties and structural behavior of cold-formed steel elliptical hollow section stub columns.” Thin Walled Struct. 134: 111–126. https://doi.org/10.1016/j.tws.2018.07.055.
Dinis, P. B., D. Camotim, B. Young, and E. M. Batista. 2018. “CFS lipped channel columns affected by LDG interaction. Part II: Numerical simulations and design considerations.” Comput. Struct. 207: 200–218. https://doi.org/10.1016/j.compstruc.2017.03.017.
Dinis, P. B., B. Young, and D. Camotim. 2014a. “Local–distortional interaction in cold-formed steel rack-section columns.” Thin Walled Struct. 81: 185–194. https://doi.org/10.1016/j.tws.2013.09.010.
Dinis, P. B., B. Young, and D. Camotim. 2014b. “Strength, interactive failure and design of web-stiffened lipped channel columns exhibiting distortional buckling.” Thin Walled Struct. 81: 195–209. https://doi.org/10.1016/j.tws.2013.09.016.
Kumar, M. V., and V. Kalyanaraman. 2014. “Distortional buckling of CFS stiffened lipped channel compression members.” J. Struct. Eng. 140 (12): 04014099. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001027.
Martins, A. D., D. Camotim, P. B. Dinis, and B. Young. 2015. “Local–distortional interaction in cold-formed steel columns: Mechanics, testing, numerical simulation and design.” Structures 4: 38–57. https://doi.org/10.1016/j.istruc.2015.10.005.
Miller, T. H., and T. Pekoz. 1994. “Load-eccentricity effects on cold-formed steel lipped-channel columns.” J. Struct. Eng. 120 (3): 805–823. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:3(805).
Papangelis, J. P., and G. J. Hancock. 1995. “Computer analysis of thin-walled structural members.” Comput. Struct. 56 (1): 157–176. https://doi.org/10.1016/0045-7949(94)00545-E.
Polyzois, D., and P. Charnvarnichborikarn. 1993. “Web-flange interaction in cold-formed steel Z-section columns.” J. Struct. Eng. 119 (9): 2607–2628. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:9(2607).
Rasmussen, K. J. R. 1994. “Design of thin-walled columns with unstiffened flanges.” Eng. Struct. 16 (5): 307–316. https://doi.org/10.1016/0141-0296(94)90022-1.
Rasmussen, K. J. R., and G. J. Hancock. 1993. “The flexural behaviour of fixed-ended channel section columns.” Thin Walled Struct. 17 (1): 45–63. https://doi.org/10.1016/0263-8231(93)90018-6.
Rasmussen, K. J. R., and G. J. Hancock. 1994. “Design of thin-walled plain channel section columns against flexural buckling.” Thin Walled Struct. 20 (1–4): 219–240. https://doi.org/10.1016/0263-8231(94)90067-1.
Schafer, B. W. 2001. “Thin-walled column design considering local, distortional and Euler buckling.” In Proc., Structural Stability Research Council. Chicago, IL: Structural Stability Research Council.
Schafer, B. W., and T. Pekoz. 1998. “Direct strength prediction of cold-formed steel members using numerical elastic buckling solutions.” In Proc., 14th Int. Specialty Conf. on Cold-Formed Steel Structures. Rolla, MO: Univ. of Missouri.
Schafer, B. W., A. Sarawit, and T. Peköz. 2006. “Complex edge stiffeners for thin-walled members.” J. Struct. Eng. 132 (2): 212–226. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:2(212).
Wang, C., Z. Zhang, D. Zhao, and Q. Liu. 2016. “Compression tests and numerical analysis of web-stiffened channels with complex edge stiffeners.” J. Constr. Steel Res. 116: 29–39. https://doi.org/10.1016/j.jcsr.2015.08.013.
Yan, J., and B. Young. 2004. “Numerical investigation of channel columns with complex stiffeners—Part I: Test verification.” Thin Walled Struct. 42 (6): 883–893. https://doi.org/10.1016/j.tws.2003.12.002.
Young, B. 2004. “Design of channel columns with inclined edge stiffeners.” J. Constr. Steel Res. 60 (2): 183–197. https://doi.org/10.1016/j.jcsr.2003.09.001.
Young, B., P. B. Dinis, and D. Camotim. 2018. “CFS lipped channel columns affected by LDG interaction. Part I: Experimental investigation.” Comput. Struct. 207: 219–232. https://doi.org/10.1016/j.compstruc.2017.03.016.
Young, B., and G. J. Hancock. 2001. “Design of cold-formed channels subjected to web crippling.” J. Struct. Eng. 127 (10): 1137–1144. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:10(1137).
Young, B., and G. J. Hancock. 2002. “Tests of channels subjected to combined bending and web crippling.” J. Struct. Eng. 128 (3): 300–308. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:3(300).
Young, B., and G. J. Hancock. 2003a. “Cold-formed steel channels subjected to concentrated bearing load.” J. Struct. Eng. 129 (8): 1003–1010. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:8(1003).
Young, B., and G. J. Hancock. 2003b. “Compression tests of channels with inclined simple edge stiffeners.” J. Struct. Eng. 129 (10): 1403–1411. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:10(1403).
Young, B., and G. J. Hancock. 2004. “Web crippling of cold-formed unlipped channels with flanges restrained.” Thin Walled Struct. 42 (6): 911–930. https://doi.org/10.1016/j.tws.2003.12.001.
Young, B., and K. J. R. Rasmussen. 1998a. “Design of lipped channel columns.” J. Struct. Eng. 124 (2): 140–148. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:2(140).
Young, B., and K. J. R. Rasmussen. 1998b. “Tests of fixed-ended plain channel columns.” J. Struct. Eng. 124 (2): 131–139. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:2(131).
Young, B., N. Silvestre, and D. Camotim. 2012. “Cold-formed steel lipped channel columns influenced by local-distortional interaction: Strength and DSM design.” J. Struct. Eng. 139 (6): 1059–1074. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000694.
Young, B., N. Silvestre, and D. Camotim. 2013. “Cold-formed steel lipped channel columns influenced by local-distortional interaction: Strength and DSM design.” J. Struct. Eng. 139 (6): 1059–1074. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000694.
Young, B., and J. Yan. 2004a. “Design of cold-formed steel channel columns with complex edge stiffeners by direct strength method.” J. Struct. Eng. 130 (11): 1756–1763. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:11(1756).
Young, B., and J. Yan. 2004b. “Numerical investigation of channel columns with complex stiffeners—Part II: Parametric study and design.” Thin Walled Struct. 42 (6): 895–909. https://doi.org/10.1016/j.tws.2004.01.004.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Apr 23, 2018
Accepted: Oct 18, 2018
Published online: Feb 25, 2019
Published in print: May 1, 2019
Discussion open until: Jul 25, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.