Experimental and Analytical Investigation of Crack Spacing and Width for Overlaid RC Beams at Elevated Temperatures
Publication: Journal of Structural Engineering
Volume 143, Issue 12
Abstract
Cracking in overlay-strengthened RC structures significantly influences their structural performance; however, the effect of elevated temperatures on cracking behavior remains unclear. This work summarizes the experimental and analytical investigations of flexural crack spacing and crack widths of overlaid reinforced concrete (RC) beams at elevated temperatures. Flexural crack spacing was observed experimentally by conducting four-point bending tests on control RC beams and beams overlaid by polymer cement mortar (PCM) together with steel reinforcements at 20, 40, and 60°C during both exposure and loading. The flexural crack width was measured during testing at 20 and 40°C. The flexural crack spacing and crack width increased with increasing temperature for the same reinforcement ratio in the overlay, whereas the flexural crack spacing and crack width decreased with increasing total area of steel reinforcements in the overlay at the same temperature. Based on the existing models for predicting the average crack spacing of overlaid beams, the bond deterioration of concrete/steel and PCM/steel bonds was incorporated to predict the flexural crack spacing of overlaid beams at elevated temperatures. The flexural crack width at an elevated temperature was predicted by incorporating the flexural crack spacing and the tensile stress of tension reinforcements in both the substrate beam and overlay at the cracked section. Close agreement was obtained between the experimental and predicted values of the flexural crack spacing and width.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support from the National Key Research and Development Program of China (2016YFC0701400), the Grant-in-Aid for Scientific Research (A) of the Japan Society of Promotion of Science (No. 26249064), the Natural Science Foundation of China (Grant No. 51178206) and NEXCO Group Companies’ Support Fund to Disaster Prevention Measures on Expressways is greatly appreciated.
References
Al-Jabri, K. S., Hago, A., Al-Nuaimi, A., and Al-Saidy, A. (2005). “Concrete blocks for thermal insulation in hot climate.” Cem. Concr. Res., 35(8), 1472–1479.
Bingöl, A. F., and Gül, R. (2009). “Residual bond strength between steel bars and concrete after elevated temperatures.” Fire Saf. J., 44(6), 854–859.
CEB-FIP (Comité Euro-Internationale du Béton et Fédération Internationale e la Précontrainte). (2010). CEB-FIP model code, Lausanne, Switzerland.
CEN (European Committee for Standardization). (2004). “Design of concrete structures. I: General rules and rules or buildings.” Eurocode 2, Brussels, Belgium.
Ceroni, F., and Pecce, M. (2009). “Design provisions for crack spacing and width in RC elements externally bonded with FRP.” Compos. Part B, 40(1), 17–28.
Chiang, C.-H., and Tsai, C.-L. (2003). “Time-temperature analysis of bond strength of a rebar after fire exposure.” Cem. Concr. Res., 33(10), 1651–1654.
Chiang, C.-H., Tsai, C.-L., and Kan, Y.-C. (2000). “Acoustic inspection of bond strength of steel-reinforced mortar after exposure to elevated temperatures.” Ultrasonics, 38(1), 534–536.
CSA (Canadian Standard Association). (2004). “S474 concrete structures.” CSA-S474, Mississauga, ON, Canada.
JSCE (Japan Society of Civil Engineers). (2007). “Standard specification for concrete structures: Design.” JGC15, Tokyo.
Noël, M., and Soudki, K. (2014). “Estimation of the crack width and deformation of FRP-reinforced concrete flexural members with and without transverse shear reinforcement.” Eng. Struct., 59(Feb), 393–398.
Raoof, M., and Hassanen, M. (2000). “Peeling failure of reinforced concrete beams with fibre-reinforced plastic or steel plates glued to their soffits.” Proc. Inst. Civ. Eng. Struct. Build., 140(3), 291–305.
Rashid, K., Ueda, T., and Zhang, D. (2015a). “Study on strengthening of RC beam by overlaying with polymer cement mortar at elevated temperature.” Proc., Symp. on Reliability of Engineering System, Tongji University Press, Beijing.
Rashid, K., Ueda, T., Zhang, D., and Fujima, S. (2014). “Tensile strength and failure modes of concrete repaired by polymer cement mortar in hot region.” Proc., 6th Int. Conf. of Asian Concrete Federation, Korea Concrete Institute, Seoul, 1338–1345.
Rashid, K., Ueda, T., Zhang, D., and Fujima, S. (2015b). “Study on behavior of polymer cement mortar in severe environmental conditions.” Proc., 37th Annual Convention of Japan Concrete Institute (JCI), Japan Concrete Institute, Tokyo, 1597–1602.
Rashid, K., Ueda, T., Zhang, D., and Miyaguchi, K. (2015c). “Study on influence of temperature on bond integrity between polymer cement mortar and concrete.” Proc., 5th Int. Conf. on Advances in Construction Materials, University of British Columbia Press, Vancouver, BC, Canada.
Rashid, K., Ueda, T., Zhang, D., Miyaguchi, K., and Nakai, H. (2015d). “Experimental and analytical investigations on the behavior of interface between concrete and polymer cement mortar under hygrothermal conditions.” Constr. Build. Mater., 94(Sep), 414–425.
Rashid, K., Zhang, D., Ueda, T., and Jin, W. (2016). “Investigation on concrete-PCM interface under elevated temperature: At material level and member level.” Constr. Build. Mater., 125(Oct), 465–478.
Satoh, K., and Kodama, K. (2005). “Central peeling failure behavior of polymer cement mortar retrofitting of reinforced concrete beams.” J. Mater. Civ. Eng., 126–136.
Zhang, D., Ueda, T., and Furuuchi, H. (2011). “Average crack spacing of overlay-strengthened RC beams.” J. Mater. Civ. Eng., 1460–1472.
Zhang, D., Ueda, T., and Furuuchi, H. (2012). “Concrete cover separation failure of overlay-strengthened reinforced concrete beams.” Constr. Build. Mater., 26(1), 735–745.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Jul 13, 2016
Accepted: Jun 9, 2017
Published online: Sep 29, 2017
Published in print: Dec 1, 2017
Discussion open until: Feb 28, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.