In-Plane Cyclic Testing of Concrete-Filled Sandwich Steel Panel Walls with and without Boundary Elements
Publication: Journal of Structural Engineering
Volume 143, Issue 9
Abstract
Concrete-filled sandwich steel panel (CFSSP) walls are composed of two steel skin plates interconnected by tie bars, with the space between the skin plates filled with concrete. These walls are attractive for use in seismic regions, but limited knowledge exists on their in-plane cycling inelastic flexural behavior. This paper reports results from an experimental study investigating this behavior by testing four cantilever CFSSP walls with and without circular boundary elements, having length-to-width ratios of 2.46 and 2.76, respectively. All of the tested walls were able to exceed their theoretical plastic moment capacity, calculated assuming a full plastic stress distribution of the cross section. The tested specimens exhibited stable ductile behavior up to 3% drift (and beyond in some conditions). Local buckling of the steel skin led to minor degradation in flexural strength. Fracture of the skin plates eventually developed as the ultimate failure mode. The effect of using different tie bars spacing to steel plate thickness ratios, and different techniques for welding the tie bars to the skin plates, are also addressed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by AISC and the Egyptian Ministry of Higher Education. However, any opinions, findings, conclusions, and recommendations presented in this paper are those of the authors and do not necessarily reflect the views of the sponsors.
References
ABAQUS [Computer software]. Dassault Systemes, Providence, RI.
AISC. (2010). “Seismic provisions for structural steel buildings.” AISC 341, Chicago.
AISC. (2016). “Seismic provisions for structural steel buildings.” AISC 341-16, Chicago.
Alzeni, Y., and Bruneau, M. (2014). “Cyclic inelastic behavior of concrete filled sandwich panel walls subjected to in plane flexure.”, MCEER Univ. at Buffalo, the State Univ. of New York, Buffalo, NY.
ASTM. (2010). “Standard specification for welded and seamless steel pipe piles.” ASTM A252, West Conshohocken, PA.
ASTM. (2015). “Standard specification for high-strength low-alloy columbium-vanadium structural steel.” ASTM A572, West Conshohocken, PA.
ASTM. (2017). “Standard test methods and definitions for mechanical testing of steel products.” ASTM A370, West Conshohocken, PA.
ATC (Applied Technology Council). (1992). “The guidelines for cyclic seismic testing of components of steel structures.” Redwood City, CA.
Bowerman, H., Gough, M., and King, C. (1999). Bi-steel design and construction guide, British Steel Ltd, Scunthorpe, U.K.
Bruneau, M., Uang, C. M., and Sabelli, R. (2011). Ductile design of steel structures, 2nd Ed., McGraw-Hill, New York, 921.
Cho, S. H., Tupper, B., Cook, W. D., and Mitchell, D. (2004). “Structural steel boundary elements for ductile concrete walls.” J. Struct. Eng., 762–768.
Corus. (2003), Bi-steel design and construction guide, 2nd Ed., Corus UK Ltd., Scunthorpe, U.K.
Corus. (2007), “Fast steel cores.” AISC, Modern Steel Construction Magazine, Chicago.
Dan, D., Fabian, A., and Stoian, V. (2011). “Theoretical and experimental study on composite steel-concrete shear walls with vertical steel encased profiles.” J. Constr. Steel Res., 67(5), 800–813.
El-Bahey, S., and Bruneau, M. (2011). “Bridge piers with structural fuses and bi-steel columns. I: Experimental testing.” J. Bridge Eng., 25–35.
Eom, T.-S., Park, H.-G., Lee, C.-H., Kim, J.-H., and Chang, I.-H. (2009). “Behavior of double skin composite wall subjected to in-plane cyclic loading.” J. Struct. Eng., 1239–1249.
Epackachi, S., Nguyen, N. H., Whittaker, A. S., and Varma, A. H. (2014). “In-plane seismic behavior of rectangular steel-plate composite wall piers.” J. Struct. Eng., 04014176.
Ge, H., and Usami, T. (1996). “Cyclic tests of concrete-filled steel box columns.” J. Struct. Eng, 1169–1177.
Hossain, K. A., and Wright, H. D. (1998). “Performance of profiled concrete shear panels.” J. Struct. Eng., 368–381.
Kawashima, K., and Unjoh, S. (1997). “The damage of highway bridges in the 1995 Hyogo-Ken Nanbu earthquake and its impact on Japanese seismic design.” J. Earthquake Eng., 1(3), 505–541.
Kurt, E. G., Varma, A. H., Booth, P. N., and Whittaker, A., (2016). “In-plane behavior and design of rectangular SC wall piers without boundary elements.” J. Struct. Eng., 04016026.
Liao, F.-Y., Han, L.-H., and Tao, Z. (2012). “Performance of reinforced concrete shear walls with steel reinforced concrete boundary columns.” Eng. Struct., 44, 186–209.
Lin, Y. C., and Tsai, K. C. (2004). “Seismic responses of steel shear wall constructed with restrainers.”, National Center for Research on Earthquake Engineering, Taipei, Taiwan (in Chinese).
Rahai, A., and Hatami, F. (2009). “Evaluation of composite shear wall behavior under cyclic loadings.” J. Constr. Steel Res., 65(7), 1528–1537.
Ramesh, S., Kreger, M. E., and Bowman, M. D. (2013). “Behavior and design of earthquake-resistant dual-plate composite shear wall systems.” ⟨http://www.pankowfoundation.org/grants.cfm?prodonly=1⟩ (May 24, 2013).
Roeder, C. W., Macrae, G., Gunderson, C., and Lehman, D. (2003). “Seismic design criteria for CFT braced frame connections” Proc., Int. Workshop on Steel and Concrete Composite Construction, Taipei, Taiwan, 97–106.
Sener, K., and Varma, A. H. (2014). “Steel-plate composite SC walls: Experimental database and design for out-of-plane shear.” J. Constr. Steel Res., 100, 197–210.
Sener, K., Varma, A. H., and Ayhan, D. (2016). “Steel-plate composite SC walls: Experimental database and design for out-of-plane flexure.” J. Constr. Steel Res., 108, 46–59.
Seo, J., Varma, A. H., Sener, K., and Ayhan, D. (2016). “Steel-plate composite (SC) walls: In-plane shear behavior, database, and design.” J. Constr. Steel Res., 119, 202–215.
Usami, T., and Ge, H. (1994). “Ductility of concrete-filled steel box columns under cyclic loading.” J. Struct. Eng, 2021–2040.
Varma, A. H., Malushte, S., Sener, K., and Lai, Z. (2014). “Steel-plate composite (SC) walls for safety related nuclear facilities: Design for in-plane force and out-of-plane moments.” Nucl. Eng. Des., 46(8), 240–249.
Wright, H. (1995). “Local stability of filled and encased steel sections.” J. Struct. Eng., 1382–1388.
Wright, H. (1998). “Axial and bending behavior of composite walls.” J. Struct. Eng., 758–764.
Zhang, K., Varma, A. H., Malushte, S., and Gallocher, S. (2014). “Effects of shear connectors on the local buckling and composite action in steel concrete composite walls.” Nucl. Eng. Des., 46(8), 231–239.
Zhao, Q., and Astaneh-Asl, A. (2004). “Cyclic behavior of traditional and innovative composite shear walls.” J. Struct. Eng., 271–284.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Apr 29, 2015
Accepted: Jan 4, 2017
Published online: Jun 21, 2017
Published in print: Sep 1, 2017
Discussion open until: Nov 21, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.