Buildings with Rigid Walls and Flexible Roof Diaphragms. II: Evaluation of a New Seismic Design Approach Based on Distributed Diaphragm Yielding
Publication: Journal of Structural Engineering
Volume 142, Issue 3
Abstract
A seismic collapse evaluation study of buildings with rigid walls and flexible roof diaphragms (RWFD) presented in the companion paper indicates that this type of structure, as designed to current seismic design provisions in the United States, does not satisfy FEMA P695 performance criteria for Risk Category II Buildings. The seismic performance of RWFD buildings is often characterized by large deformations and yielding in the roof diaphragm rather than in the vertical elements of the seismic force–resisting system (SFRS). In this paper, a new seismic design approach is proposed to account for flexible roof diaphragm response. The proposed approach relies on distributed yielding in the roof diaphragm as the predominant inelastic response under extreme ground shaking. This is obtained by strengthening the end diaphragm regions, thereby allowing yielding to spread deeper into the diaphragm. The basic steps of the design approach and its limitations are described. A validation study of the proposed design procedure is conducted for 17 RWFD building archetypes with wood roof diaphragms in accordance with the FEMA P695 methodology. The results of this study indicate that the proposed seismic design approach, produces a system that meets the probability of collapse requirement for a Risk Category II building of the FEMA P695 methodology under maximum considered earthquake ground motion for RWFD buildings with wood roof diaphragms.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was conducted as part of a project directed by the Building Seismic Safety Council (BSSC) of the National Institute of Building Sciences (NIBS) and funded by the Federal Emergency Management Agency (FEMA) under DHS/FEMA Contract HSFEHQ-09-D-0147, Task Order HSFE60-12-J-0002C. The main objective of this project was to develop simplified seismic design procedures for rigid wall-flexible roof diaphragm buildings. This financial support is gratefully acknowledged. Any opinions, findings, conclusions, or recommendations expressed in this paper are those of the authors and do not necessarily reflect the views of NIBS and FEMA. The Structural Engineering and Earthquake Simulation Laboratory (SEESL) at the University at Buffalo is also acknowledged for providing partial financial support to the first author.
References
ACI (American Concrete Institute). (2011). “Building code requirements for structural concrete and commentary.” ACI 318-11, Farmington Hills, MI.
AF&PA. (2008). “ASD/LRFD wind & seismic special design provisions for wind and seismic with commentary (SDPWS).” American Forest & Paper Association, Washington, DC.
ASCE. (2010). Minimum design loads for buildings and other structures, ASCE, Reston, VA.
AWC (American Wood Council). (2012). “National design specification (NDS) for wood construction.” Leesburg, VA.
Christovasilis, I. P., Filiatrault, A., and Wanitkorkul, A. (2009). “Seismic testing of a full-scale two-story light-frame wood building: NEESWood benchmark test.”, Multidisciplinary Center for Earthquake Engineering, Buffalo, NY.
Cohen, G. L., Klingner, R. E., Hayes, J. R., and Sweeney, S. C. (2004). “Seismic evaluation of low-rise reinforced masonry buildings with flexible diaphragms. I. Seismic and quasi-static testing.” Earthquake Spectra, 20(3), 779–801.
FEMA. (2009). “Quantification of building seismic performance factors.” FEMA P695, Washington, DC.
FEMA. (2011). “Quantification of building seismic performance factors: Component equivalency methodology.” FEMA P795, Washington, DC.
FEMA. (2015). “Seismic design of rigid wall-flexible diaphragm buildings: An alternate procedure.” FEMA P1026, Washington, DC.
Fonseca, F. S., Sterling, K. R., and Campbell, S. H. (2002). Nail, wood screw, and staple fastener connections, CUREE, Richmond, CA.
IBC (International Building Code). (2000). “International code council.” Washington, DC.
IBC (International Building Code). (2012). “International code council.” Washington, DC.
ICBO (International Conference of Building Officials). (1994). “Uniform building code.” Washington, DC.
ICBO (International Conference of Building Officials). (1997). “Uniform building code.” Washington, DC.
Koliou, M. (2014). “Seismic analysis and design of rigid wall-flexible roof diaphragm structures.” Ph.D. thesis, Univ. at Buffalo–State Univ. of New York, Buffalo, NY.
Koliou, M., Filiatrault, A., Kelly, D. J., and Lawson, J. (2015a). “Buildings with rigid walls and flexible roof diaphragms. I: Seismic collapse evaluation of existing design provisions.” J. Struct. Eng, in press.
Koliou, M., Filiatrault, A., Kelly, D. J., and Lawson, J. (2015b). “Distributed yielding concept for improved seismic collapse performance of rigid wall-flexible diaphragm buildings.” J. Struct. Eng., 04015137.
Lawson, J., Kelly, D. J., Koliou, M., and Filiatrault, A. (2014). “Evaluating existing and proposing new seismic design provisions for rigid wall-fexible diaphragm buildings.” Proc., SEAOC 2014 83rd Annual Convention, Structural Engineering Association of California, Indian Wells, CA.
Newmark, N. M., and Hall, W. J. (1973). “Seismic design criteria for nuclear reactor facilities.”, National Bureau of Standards, U.S. Dept. of Commerce, Washington, DC, 209–236.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Nov 11, 2014
Accepted: Sep 14, 2015
Published online: Dec 10, 2015
Published in print: Mar 1, 2016
Discussion open until: May 10, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.