Buildings with Rigid Walls and Flexible Roof Diaphragms. I: Evaluation of Current U.S. Seismic Provisions
Publication: Journal of Structural Engineering
Volume 142, Issue 3
Abstract
Buildings having rigid walls and flexible roof diaphragms (RWFD) are a type of building construction widely used for light industry in the United States; they incorporate rigid in-plane concrete or masonry walls and flexible in-plane wood, steel, or hybrid roof diaphragms. In this first of two companion papers, the probability of collapse of this type of building designed to current code provisions in the United States, given an MCE earthquake event, is evaluated according to the FEMA P695 methodology for a large set of representative building archetypes. The results of the study indicate that current code provisions for this type of building do not satisfy the collapse objective requirements of FEMA P695 under maximum considered earthquake ground motions. This is because the analysis provisions are based on assumed yielding of the walls rather than the roof diaphragm. Also, current code provisions considerably underestimate the period of RWFD buildings. To assist with creating provisions that take into account large flexible diaphragm deformations, a semi-empirical formula to estimate the fundamental period of RWFD buildings that accounts for roof diaphragm flexibility is derived in this paper. A new proposed seismic design approach for RWFD buildings is developed and evaluated in the second companion paper.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was conducted as part of a project directed by the Building Seismic Safety Council (BSSC) of the National Institute of Building Sciences (NIBS) and funded by the Federal Emergency Management Agency (FEMA) under DHS/FEMA Contract HSFEHQ-09-D-0147, Task Order HSFE60-12-J-0002C. The main objective of this project was to develop simplified seismic design procedures for rigid wall-flexible roof diaphragm buildings. This financial support is gratefully acknowledged. Any opinions, findings, conclusions, or recommendations expressed in this paper are those of the authors and do not necessarily reflect the views of NIBS and FEMA. The Structural Engineering and Earthquake Simulation Laboratory (SEESL) at the University at Buffalo is also acknowledged for providing partial financial support to the first author.
References
ACI (American Concrete Institute). (2011a). “Building code requirements and specification for masonry structures and related commentaries.” ACI 530-11, Farmington Hills, MI.
ACI (American Concrete Institute). (2011b). “Building code requirements for structural concrete and commentary.” ACI 318-11, Farmington Hills, MI.
AF&PA. (2008). “ASD/LRFD wind & seismic special design provisions for wind and seismic with commentary (SDPWS).” American Forest & Paper Association, Washington, DC.
ASCE. (2005). “Minimum design loads for buildings and other structures.” ASCE/SEI 7-05, Reston, VA.
ASCE. (2010). Minimum design loads for buildings and other structures, ASCE/SEI 7-10, Reston, VA.
AWC (American Wood Council). (2012). “National design specification (NDS) for wood construction.” Leesburg, VA.
Carr, A. J. (2007). “RUAUMOKO2D.” Univ. of Canterbury, Christchurch, New Zealand.
Christovasilis, I. P., Filiatrault, A., and Wanitkorkul, A. (2009). “Seismic testing of a full-scale two-story light-frame wood building: NEESWood benchmark test.”, Multidisciplinary Center for Earthquake Engineering, Buffalo, NY.
Cohen, G. L., Klingner, R. E., Hayes, J. R., and Sweeney, S. C. (2004). “Seismic evaluation of low-rise reinforced masonry buildings with flexible diaphragms. I. Seismic and quasi-static testing.” Earthquake Spectra, 20(3), 779–801.
EQE Engineering. (1989). “The October 17, 1989 Loma Prieta earthquake.” EQE Engineering, San Francisco.
FEMA. (2009). “Quantification of building seismic performance factors.” FEMA P695, Washinghton, DC.
FEMA. (2015). “Seismic design of rigid wall-flexible diaphragm buildings: An alternate procedure.” FEMA P1026, Washinghton, DC.
Fonseca, F. S., Sterling, K. R., and Campbell, S. H. (2002). Nail, wood screw, and staple fastener connections, CUREE, Richmond, CA.
Freeman, S. A., Searer, G. R., and Gilmartin, U. M. (2002). “Proposed seismic design provisions for rigid shear wall/flexible diaphragm structures.” Proc., 7th U.S. National Conf. on Earthquake Engineering, Boston.
Hamburger, R. O., McCormick, D. L., and Hom, S. (1988). “The Whittier Narrows earthquake of October 1, 1987—Performance of tilt-up buildings.” Earthquake Spectra, 4(2), 219–254.
IBC (International Building Code). (2012). “International code council.” Washington, DC.
Koliou, M. (2014). “Seismic analysis and design of rigid wall-flexible roof diaphragm structures.” Ph.D. dissertation, Univ. at Buffalo–State Univ. of New York, Buffalo, NY.
Koliou, M., Filiatrault, A., Kelly, D. J., and Lawson, J. (2014). “Numerical framework for seismic collapse assessment of rigid wall-flexible diaphragm structures.” Proc., 10th U.S. National Conf. on Earthquake Engineering, Anchorage, AK, 11.
Koliou, M., Filiatrault, A., Kelly, D. J., and Lawson, J. (2015). “Distributed yielding concept for improved seismic collapse performance of rigid wall-flexible diaphragm buildings.” J. Struct. Eng., 04015137.
Lawson, J., Kelly, D. J., Koliou, M., and Filiatrault, A. (2014). “Evaluating existing and proposing new seismic design provisions for rigid wall-flexible diaphragm buildings.” Proc., SEAOC 2014 83rd Annual Convention, Structural Engineering Association of California, Indian Wells, CA.
MATLAB 8.10.1.604 [Computer software]. Mathworks, Natick, MA.
Press, W. H., Teukolsky, S. A., Vetterling, W. T., and Flannery, B. P. (1997). Numerical recipes in Fortran 77: The art of scientific computing, Cambridge University Press, Cambridge, England.
Rogers, C. A., and Tremblay, R. (2003a). “Inelastic seismic response of frame connectors for steel roof deck diaphragms.” J. Struct. Eng., 1647–1657.
Rogers, C. A., and Tremblay, R. (2003b). “Inelastic seismic response of side lap connectors for steel roof deck diaphragms.” J. Struct. Eng., 1637–1646.
SDI (Steel Deck Institute). (2004). Diaphragm design manual, 3rd Ed., Fox River Grove, IL.
SEAONC (Structural Engineers Association of Northern California). (2001). “Guidelines for seismic evaluation and rehabilitation of tilt-up buildings and other rigid wall/flexible diaphragm structures.” San Francisco.
Stewart, W. G. (1987). “The seismic design of plywood sheathed shear walls.” Ph.D. dissertation, Univ. of Canterbury, Christchurch, New Zealand.
Tremblay, R., Martin, E., Yang, W., and Rogers, C. A. (2004). “Analysis, testing and design of steel roof deck diaphragms for ductile earthquake resistance.” J. Earthquake Eng., 8(5), 775–816.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Nov 11, 2014
Accepted: Sep 14, 2015
Published online: Dec 10, 2015
Published in print: Mar 1, 2016
Discussion open until: May 10, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.