Experimental Study of Longitudinally Stiffened Web Channels Subjected to Combined Bending and Shear
Publication: Journal of Structural Engineering
Volume 141, Issue 11
Abstract
The direct strength method (DSM) of design of cold-formed sections has been recently extended in the North American Specification for Cold-Formed Steel Structural Members NAS S100:2012 to include shear. The two new features of the DSM rules for shear researched are the effect of full-section shear buckling as opposed to web-only shear buckling and tension field action (TFA). The prequalified sections in the rules include sections with flat webs and webs with small intermediate longitudinal stiffeners. In order to extend the range to larger intermediate stiffeners as occurs in practice, a series of fourteen shear tests have been performed at the University of Sydney for C-sections with rectangular stiffeners of varying sizes. Six different types of stiffeners were tested with an additional preferred plain section. Each type of section was tested twice to ensure accuracy. As the web stiffener sizes increase, the shear buckling and strength of the sections are expected to improve accordingly. However, the tests show that the shear ultimate strengths only increase slightly in association with the respective increases of stiffener sizes. The test results are compared with the DSM design rules for shear and found to be lower than those predicted by the DSM curve for shear with TFA. The test failures were observed mainly due to the combined bending and shear modes. The effect of the bending is therefore significant and starts to govern when the shear capacity is significantly strengthened by adding the large longitudinal web stiffener. The test results are subsequently plotted against the DSM interaction curves between bending and shear, where the interaction is found to be significant. Recommendations for prequalified sections with longitudinally stiffened web channels in combined bending and shear are validated in the paper.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding provided by the Australian Research Council Discovery Project Grant DP110103948 has been used to perform this project.
References
AISI. (2012). “North American specification for the design of cold-formed steel structural members.”, American Iron and Steel Institute, Washington, DC.
Basler, K. (1961). “Strength of plate girders in shear.” J. Struct. Div., 87(ST7), 151–180.
Hancock, G. J., and Pham, C. H. (2011). “A signature curve fold-formed channel sections in pure shear.”, School of Civil Engineering, Univ. of Sydney, Sydney, Australia.
Hancock, G. J., and Pham, C. H. (2012). “Direct strength method of design for shear of cold-formed channels based on a shear signature curve.” Proc., 21st Int. Specialty Conf. on Cold-Formed Steel Structures, Missouri Univ. of Science & Technology, Rolla, MO, 207–221.
Hancock, G. J., and Pham, C. H. (2013). “Shear buckling of channel sections with simply supported ends using the semi-analytical finite strip method.” Thin Walled Struct., 71, 72–80.
Lau, S. C. W., and Hancock, G. J. (1986). “Buckling of thin flat-walled structures by a spline finite strip method.” Thin Walled Struct., 4(4), 269–294.
Pham, C. H., and Hancock, G. J. (2009). “Shear buckling of thin-walled channel sections.” J. Constr. Steel Res., 65(3), 578–585.
Pham, C. H., and Hancock, G. J. (2010). “Experimental investigation of high strength cold-formed C-section in combined bending and shear.” J. Struct. Eng., 866–878.
Pham, C. H., and Hancock, G. J. (2012a). “Direct strength design of cold-formed C-section for shear and combined actions.” J. Struct. Eng., 759–768.
Pham, C. H., and Hancock, G. J. (2012b). “Elastic buckling of cold-formed channel sections in shear.” Thin Walled Struct., 61, 22–26.
Pham, C. H., and Hancock, G. J. (2013). “Experimental investigation and direct strength design of high strength, complex C-sections in pure bending.” J. Struct. Eng., 1842–1852.
Pham, S. H., Pham, C. H., and Hancock, G. J. (2012a). “Shear buckling of channel sections with complex web stiffeners.”, School of Civil Engineering, Univ. of Sydney, Sydney, Australia.
Pham, S. H., Pham, C. H., and Hancock, G. J. (2012b). “Shear buckling of thin-walled channel sections with complex stiffened webs.” Proc., 21st Int. Specialty Conf. on Cold-Formed Steel Structures, Missouri Univ. of Science & Technology, Rolla, MO, 281–262.
Plank, R. J., and Wittrick, W. H. (1974). “Buckling under combined loading of thin, flat-walled structures by a complex finite strip method.” Int. J. Numer. Methods Eng., 8(2), 323–339.
Standards Australia. (1991). “Methods for tensile testing of metals.”, Standards Australia/Standards New Zealand, Sydney.
Standards Australia. (2005). “Cold-formed steel structures.”, Standards Australia/Standards New Zealand, Sydney.
Standards Australia. (2011). “Continuous hot-dipped metallic coated steel sheet and strip—Coatings of zinc and zinc alloyed with aluminium and magnesium.”, Sydney, Australia.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 141 • Issue 11 • November 2015
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jul 4, 2014
Accepted: Dec 19, 2014
Published online: Feb 9, 2015
Discussion open until: Jul 9, 2015
Published in print: Nov 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.