Tension Chord Model Modification for Uniaxial Unloading and Reloading in Elastic and Plastic States
This article has been corrected.
VIEW CORRECTIONThis article is a reply.
VIEW THE ORIGINAL ARTICLEPublication: Journal of Structural Engineering
Volume 140, Issue 10
Abstract
The bond properties between concrete and steel reinforcement influence structural stiffness and deformation behavior as a result of tension stiffening. In specific cases, the load-bearing capacity of engineering structures depends on the deformation behavior and may be affected by load history because of unloading and reloading (UR) cycles. The bond stress-slip relationship of the original tension chord model was modified to make it applicable for general UR cycles in the elastic and plastic states of the reinforcing steel by reducing the admissible bond shear stress, thus taking into account the progressive and irreversible damage to the concrete around the ribbed bar attributable to yielding and the load history. The residual tension stiffening in the elastic state is influenced by the degree of slip reversal, for which an analytical function was found that is dependent on the crack spacing, bond strength, and stress levels before and after unloading. The proposed analytical model was successfully validated with experimental results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to acknowledge the support and funding of this research by the Swiss Federal Commission for Technology and Innovation CTI (Grant No. 11569.1 PFIW-IW) and F.J. Aschwanden AG, Lyss, Switzerland.
References
Alvarez, M. (1998). “Einfluss des Verbundverhaltens auf das Verformungsvermögen von Stahlbeton.” Doctoral thesis, ETH Zürich, Switzerland (in German).
Balázs, G. L. (1991). “Fatigue of bond.” ACI Mater. J., 88(6), 620–629.
Borosnyói, A., and Balázs, G. L. (2005). “Models for flexural cracking in concrete: The state of the art.” Struct. Concr., 6(2), 53–62.
Burns, C. (2011). “Serviceability analysis of reinforced concrete based on the tension chord model.” Doctoral thesis, ETH Zürich, Switzerland.
Fürst, A. (2001). “Vorgespannte Betonzugglieder im Brückenbau.” Doctoral thesis, ETH Zürich, Switzerland (in German).
Goto, Y. (1971). “Cracks formed in concrete around deformed tension bars.” Proc., ACI J., 68(4), 244–251.
International Federation for Structural Concrete (FIB). (2000). “Bond of reinforcement in concrete.” FIB Bulletin No. 10, FIB, Lausanne, Switzerland.
International Federation for Structural Concrete (FIB). (2012). “Model code 2010—Final draft.” FIB Bulletin No. 66, Vol. 2, FIB, Lausanne, Switzerland.
Kaufmann, W. (1998). “Strength and deformations of structural concrete subjected to in-plane shear and normal forces.” Doctoral thesis, ETH Zürich, Switzerland.
Kenel, A. (2002). “Biegetragverhalten und Mindestbewehrung von Stahlbetonbauteilen.” Doctoral thesis, ETH Zürich, Switzerland (in German).
Kenel, A., and Marti, P. (2002). “Faseroptische Dehnungsmessungen an einbetonierten Bewehrungsstäben.”, ETH Zürich, Switzerland (in German).
Kenel, A., Nellen, P., Frank, A., and Marti, P. (2005). “Reinforcing steel strains measured by Bragg grating sensors.” J. Mater. Civ. Eng., 423–431.
Leonhardt, F. (1978). Vorlesungen über Massivbau. Vierter Teil: Nachweis der Gebrauchsfähigkeit, 2nd Ed., Springer, New York, (in German).
Marti, P., Alvarez, M., Kaufmann, W., and Sigrist, V. (1998). “Tension chord model for structural concrete.” Struct. Eng. Int., 8(4), 287–298.
Muttoni, A. (2008). “Punching shear strength of reinforced concrete slabs without transverse reinforcement.” ACI Struct. J., 105(4), 440–450.
Pfyl, T. (2003). “Tragverhalten von Stahlfaserbeton.” Ph.D. thesis, ETH Zürich, Switzerland, (in German).
Pfyl, T., and Marti, P. (2001). “Versuche an stahlfaserverstärkten Stahlbetonelementen.”, ETH Zürich, Zürich, Switzerland, (in German).
Ramberg, W., and Osgood, W. R. (1943). “Description of stress-strain curves by three parameters.”, National Advisory Committee for Aeronautics, Washington, DC.
Rehm, G. (1961). “Über die Grundlagen des Verbundes zwischen Stahl und Beton.” Deutscher Ausschuss für Stahlbeton, Vol. 138, Ernst Berlin, Germany, (in German).
Shima, H., Chou, L.-L., and Okamura, H. (1987). “Micro and macro models for bond in reinforced concrete.” J. Facul. Eng. Univ. Tokyo, 39(2), 133–194.
Shima, H., Kanakubo, T., Uchida, Y., and Watanabe, K. (2011). “Technical committee on bond models and their applications for numerical analyses.”, Japanese Concrete Institute, Tokyo, 25–48.
Sigrist, V. (1995). “Zum Verformungsvermögen von Stahlbetonträgern.” Doctoral thesis, ETH Zürich, Switzerland (in German).
Swiss Society of Engineers and Architects. (2004). “Concrete structures.”, Zurich, Switzerland.
Zanuy, C., Albajar, L., and de la Fuente, P. (2010). “On the cracking behaviour of the reinforced concrete tension chord under repeated loading.” Mater. Struct., 43(5), 611–632.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jul 12, 2013
Accepted: Nov 7, 2013
Published online: May 15, 2014
Published in print: Oct 1, 2014
Discussion open until: Oct 15, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.