Ultimate Resistance Design of Shuttle-Shaped Steel Tubular Latticed Columns
Publication: Journal of Structural Engineering
Volume 140, Issue 10
Abstract
As a new type of nonprismatic built-up columns, the shuttle-shaped steel tubular latticed (SSTL) column is widely used in engineering structures. However, there are no methods available to test its ultimate resistance design and little research about its behavior. This article investigates the elastic buckling behavior of three-tube SSTL columns only with horizontal web members and subject to an axial load, and it is found that the SSTL column may buckle in a symmetric flexure-dominated mode or an antisymmetric shear-dominated mode, depending on distributions of sectional flexural stiffness and shear stiffness along the column length. The formulas for predicting elastic buckling loads are derived by accounting for the effects of sectional shear deformations. With the elastic buckling loads obtained, formulas for the effective slenderness and the normalized effective slenderness are proposed. The resistance design procedure for SSTL columns only with horizontal web members is developed in association with Chinese code GB50017 and Eurocode 3. Comparisons with finite element results demonstrate the proposed procedure can provide reasonably accurate predictions for the resistances of SSTL columns.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
We gratefully acknowledge financial support from Tsinghua University of China under grant No. 2012Z10134.
References
American Institute of Steel Construction (AISC). (1999). Load and resistance factor design specification for structural steel buildings, Chicago.
Aristizábal-Ochoa, J. D. (1993). “Statics, stability and vibration of non-prismatic beams and columns.” J. Sound. Vib., 162(3), 441–455.
Aslani, F., and Goel, S. C. (1991). “An analytical criterion for buckling strength of built-up compression members.” Eng. J., 28(4), 159–168.
China Association for Standardization. (2010). CECS280 technical specification for structures with steel hollow sections, China Planning Press, Beijing.
Deng, K., and Guo, Y. L. (2005). “Buckling behavior of shuttle-shaped latticed tubular steel column under axially compressive load.” Eng. Mech., 22(4), 31–37 (in Chinese).
Duan, L., and Chen, W. F. (1988). “Design rules of built-up members in load and resistance factor design.” J. Struct. Eng., 2544–2554.
Duan, L., Reno, M., and Uang, C. (2002). “Effect of compound buckling on compression strength of built-up members.” Eng. J., 39(1), 30–37.
European Committee for Standardization. (2005). “Design of steel structures—Part 1.1: General rules and rules for buildings.”, Brussels, Belgium.
Guo, Y., and Wang, J. (2009). “Instability behavior and application of prismatic multi-tube latticed steel column.” J. Construct. Steel Res., 65(1), 12–22.
Guo, Y. L., Chen, G. D., and Lan, Y. (2002). “Ultimate load-carrying capacity of 3-tube shuttle-shaped steel latticed column.” J. Build. Struct., 23(5), 25–30 (in Chinese).
Guo, Y. L., and Lan, Y. (2002). “Experimental investigation of the full scale 3-tube shuttle-shaped steel latticed column.” J. Build. Struct., 23(5), 31–40 (in Chinese).
Kalochairetis, K. E., and Gantes, C. J. (2011). “Numerical and analytical investigation of collapse loads of laced built-up columns.” Comput. Struct., 89(11), 1166–1176.
Li, J. J., and Li, G. Q. (2004). “Buckling analysis of tapered lattice columns using a generalized finite element.” Comm. Numer. Meth. Eng., 20(6), 479–488.
Liu, J. L., Lue, D. M., and Lin, C. H. (2009). “Investigation on slenderness ratios of built-up compression members.” J. Construct. Steel Res., 65(1), 237–248.
Lue, D. M., Yen, T., and Liu, J. L. (2006). “Experimental investigation on built-up columns.” J. Construct. Steel Res., 62(12), 1325–1332.
Marques, L., Taras, A., Simões da Silva, L., Greiner, R., and Rebelo, C. (2012). “Development of a consistent buckling design procedure for tapered columns.” J. Construct. Steel Res., 72(1), 61–74.
Multiphysics, ANSYS 13.0 [computer software]. Ansys, Canonsberg, PA.
National Standard of People’s Republic of China. (2003). GB50017 Code for design of steel structures, China Architecture and Building Press, Beijing (in Chinese).
Razdolsky, A. G. (2005). “Euler critical force calculation for laced columns.” J. Eng. Mech., 997–1003.
Serna, M. A., Ibáñez, J. R., and López, A. (2011). “Elastic flexural buckling of non-uniform members: Closed-form expression and equivalent load approach.” J. Construct. Steel Res., 67(7), 1078–1085.
Temple, M. C., and Elmahdy, G. M. (1996). “Slenderness ratio of main members between interconnectors of built-up compression members.” Can. J. Civ. Eng., 23(6), 1295–1304.
Timoshenko, S. P., and Gere, J. M. (1961). Theory of elastic stability, McGraw Hill, New York.
Tong, G. S. (2005). In-plane stability of steel structures, China Architecture and Building Press, Beijing (in Chinese).
Tong, G. S., and Chen, S. F. (1989). “An interactive buckling theory for built-up beam-columns and its application to centrally compressed built-up members.” J. Construct. Steel Res., 14(3), 221–241.
Ziemian, R. D., ed. (2010). Guide to stability design criteria for metal structures, 6th Ed., John Wiley & Sons, Hoboken.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jul 9, 2013
Accepted: Nov 7, 2013
Published online: May 14, 2014
Published in print: Oct 1, 2014
Discussion open until: Oct 14, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.