Using Dune Sand in Controlled Low-Strength Material for Backfilling: Field Installation and Numerical Simulation
Publication: Journal of Pipeline Systems Engineering and Practice
Volume 12, Issue 1
Abstract
The deflection of buried pipes depends on the exerted load and the embedment material. The portion of the exerted load transferred by the embedment material depends on the stiffness of the embedment material relative to that of the pipe. In the current study, four glass-reinforced polymer (GRP) pipes were buried in two different locations at the same depth under different geotechnical and installation conditions. For each of the test locations, two installation methods, namely controlled low-strength material (CLSM) and crushed rock, were used. The CLSM mixes were designed based on available native soil to satisfy the flow and strength criteria. Pipe deflection was meticulously measured at different stages of installation. In both cases, the behavior of the pipe showed the superior performance of CLSM as the backfill material. The behavior of the pipe was also evaluated by numerical modeling. The results of the numerical simulation were then compared with field test results, which showed a reasonable agreement. The pipe deflection was also predicted by a semiempirical equation and a numerical solution for the hardened CLSM. The effect of trench width on the vertical deformation was also evaluated through a parametric study.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data and models generated or used during the current study are available from the corresponding author upon reasonable request, including laboratory tests on soils and CLSM mixes, data collected during field test, and finite-element models for different backfilling conditions.
Acknowledgments
This research was funded and financially and technically supported by Faratec Novin Parseh as the research and development (R&D) center for Farassan Industrial and Manufacturing Co., Shiraz, Iran. The full supports of Dr. Mohammad-Reza Zahir-Emami, Dr. Mahnaz Zahir-Emami, and Mr. Amin Jahedi throughout the project are gratefully acknowledged.
References
Abdel-Rahman, K., T. Gerlach, and M. Achmus. 2017. “Behavior of pipelines embedded in self-compacting materials under traffic loads.” In Proc., Int. Congress and Exhibition “Sustainable Civil Infrastructures: Innovative Infrastructure Geotechnology,” 89–99. Berlin: Springer.
ACI (American Concrete Institute). 2005. ACI publication 229-R, reapproved 2005. Farmington Hills, MI: ACI.
ASTM. 2006a. Standard practice for classification of soils for engineering purposes (unified soil classification system). West Conshohocken, PA: ASTM.
ASTM. 2006b. Standard test method for long-term ring-bending strain of fiberglass (glass-fiber-reinforced thermosetting-resin) pipe. West Conshohocken, PA: ASTM.
ASTM. 2006c. Standard test method for preparation and testing of controlled low strength material (CLSM) test cylinders. West Conshohocken, PA: ASTM.
ASTM. 2010. Standard test method for determination of external loading characteristics of plastic pipe by parallel-plate loading. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard practice for sampling freshly mixed controlled low-strength material. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard practice for the underground installation of ‘Fiberglass’ (glass-fiber reinforced thermosetting resin) pipe. West Conshohocken, PA: ASTM.
AWWA (American Water Works Association). 2013. Fiberglass pipe design. AWWA M45. Denver: AWWA.
Bellavar, F. 2013. “Large diameter steel pipe field test using controlled low strength material and stage construction modeling using 3-D nonlinear finite element analysis.” MS thesis, Faculty of the Graduate School, Univ. of Texas at Arlington.
Chittoori, B., A. J. Puppala, A. Pedarla, and D. P. R. Vanga. 2014. “Durability studies on native soil-based controlled low strength materials.” In Ground improvement and geosynthetics, 249–257. New York: ASCE.
Cho, S., and C. Vipulanandan. 2005. “Flowable backfill with flexible pipe in trench condition and FEM verification.” In Pipelines 2005: Optimizing pipeline design, operations, and maintenance in today’s economy, 1079–1088. New York: ASCE.
Dezfooli, M. S., A. Abolmaali, and M. Razavi. 2014. “Coupled nonlinear finite-element analysis of soil–steel pipe structure interaction.” Int. J. Geomech. 15 (1): 04014032. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000387.
Duncan, J. M. 1979. “Behavior and design of long-span metal culverts.” J. Geotech. Geoenviron. Eng. 105 (Mar): 14429.
Gondle, R. K. 2006. “Finite element analysis of long-term performance of buried high density polyethylene pipes.” MS thesis, Dept. of Civil and Environmental Engineering, Univ. of West Virginia.
Green, B. H., and D. W. Schmitz. 2004. “Soil-based controlled low-strength materials.” Environ. Eng. Geosci. 10 (2): 169–174. https://doi.org/10.2113/10.2.169.
Hamilton County and the City of Cincinnati, Ohio (HAMCIN). 1996. “A performance specification for controlled low strength material controlled density fill.” Accessed March 3, 2014. http://www.cincinnati-oh.gov/dote/linkservid/4B3C34CC-FAB9-4315B660D6B8C22DA441/showMeta/0/.
Howard, A. 1977. “Modulus of soil reaction values for buried flexible pipe.” J. Geotech. Eng. 103 (1): 33–43.
Katona, M. G., and J. M. Smith. 1976. “A modern approach for structural design of pipe culverts.” In Proc., 2nd Int. Conf. on Computers in Engineering and Building Design (CAD76) IPC Science. Cambridge, UK: Technology Press.
Ling, T. C., S. K. Kaliyavaradhan, and C. S. Poon. 2018. “Global perspective on application of controlled low-strength material (CLSM) for trench backfilling—An overview.” Constr. Build. Mater. 158: 535.
Mada, H. 2005. “Numerical modeling of buried pipes with flowable fill as a backfill material.” M.S. thesis, Dept. of Civil and Environmental Engineering, Univ. of West Virginia.
McGrath, T. J. 1998. “Pipe-soil interactions during backfill placement.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of Massachusetts.
Motahari, A., and A. Abolmaali. 2009. “Structural deformation characteristics of installed HDPE circular pipelines” J. Transp. Eng. 136 (4): 298–303. https://doi.org/10.1061/(ASCE)TE.1943-5436.0000091.
Puppala, A. J., B. Chittoori, and A. Raavi. 2014. “Flowability and density characteristics of controlled low-strength material using native high-plasticity clay.” J. Mater. Civ. Eng. 27 (1): 06014026. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001127.
Raavi, A. 2012. “Design of controlled low strength material for bedding and backfilling using high plastic clay.” M.S. thesis, Faculty of the Graduate School, Univ. of Texas at Arlington.
Sharma, J. R., M. Najafi, D. Marshall, V. Kaushal, and M. Hatami. 2019. “Development of a model for estimation of buried large-diameter thin-walled steel pipe deflection due to external loads.” J. Pipeline Syst. Eng. Pract. 10 (3): 04019019. https://doi.org/10.1061/(ASCE)PS.1949-1204.0000384.
Siriwardane, H. J., S. B. K. Varre, and R. K. Gondle. 2014. “Numerical modeling of long-term performance of buried pipes.” In Proc., Int. Conf. on Geotechnical Engineering. Colombo: International Conference on Geotechnical Engineering.
Spangler, M. G. 1941. The structural design of flexible pipe culverts. Ames, IA: Iowa State College.
Suleiman, M. T., R. A. Lohnes, T. J. Wipf, and F. W. Klaiber. 2002. “Analysis of deeply buried flexible pipes.” Transp. Res. Rec. 1849 (1): 124–133. https://doi.org/10.3141/1849-14.
Takou, M. 2016. “Numerical and experimental investigation of buried large-diameter steel pipe with controlled low-strength material.” Ph.D. thesis, Faculty of the Graduate School, Univ. of West Virginia.
Talesnick, M. L., and S. Frydman. 2018. “Soil pressure and pipe deformation measurements for characterizing flexible pipe—Soil systems under shallow cover.” J. Pipeline Syst. Eng. Pract. 9 (1): 04017028. https://doi.org/10.1061/(ASCE)PS.1949-1204.0000294.
Tian, Y., and M. J. Cassidy. 2008. “Modeling of pipe–soil interaction and its application in numerical simulation.” Int. J. Geomech. 4 (213): 213–229. https://doi.org/10.1061/(ASCE)1532-3641(2008)8:4(213),213%E2%80%93229.
Watkins, R. K., and M. G. Spangler. 1958. “Some characteristics of the modulus of passive resistance of soil: A study in similitude.” In Proc., Highway Research Board, 576–583. Washington, DC: Highway Research Board.
Wu, J. Y. 2005. “Soil-based flowable fill for pipeline construction.” In Pipelines 2005: Optimizing pipeline design, operations, and maintenance in today’s economy, 925–938. Reston, VA: ASCE.
Zarghamee, M. S., and D. Tigue. 1986. “Soil structure interaction of flexible pipe under pressure.” Transp. Res. Rec. 1087 (1): 46–53.
Zhang, J., D. P. Stewart, and M. F. Randolph. 2002. “Kinematic hardening model for pipeline-soil interaction under various loading conditions.” Int. J. Geomech. 4 (419): 419–446. https://doi.org/10.1061/(ASCE)1532-3641(2002)2:4(419),419446.
Information & Authors
Information
Published In
Journal of Pipeline Systems Engineering and Practice
Volume 12 • Issue 1 • February 2021
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Feb 28, 2019
Accepted: Jul 8, 2020
Published online: Sep 17, 2020
Published in print: Feb 1, 2021
Discussion open until: Feb 17, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.