Effects of Corrosion Pits on Wall Stresses in Cast-Iron Water Mains
Publication: Journal of Pipeline Systems Engineering and Practice
Volume 8, Issue 4
Abstract
Circumferential cracking or ring fracture has been identified as the most common type of failure mode for cast-iron water mains. However, the cause of circumferential cracking in water mains is not well understood. A number of different postulates exist in the literature on the causes of longitudinal stresses leading to circumferential cracking. The postulates are, however, not proven. This paper presents a finite element analysis to investigate the effect of corrosion pits on the failure mechanism of cast-iron water mains. The study shows that corrosion pits, voids in the bedding, and high relative stiffness of the pipe (with respect to the surrounding soil) can contribute to longitudinal stress development in the pipe wall. Longitudinal stress is generally higher than circumferential stress for a pipe with high relative stiffness. For a particular pipe, longitudinal stress is higher for smaller corrosion pits. Localized forces on the pipe wall from the surrounding ground can increase the longitudinal stress significantly. A localized support equivalent to a spring with a spring constant of can result in circumferential cracking of pipes. Based on the findings, a failure hypothesis has been provided for cast-iron water mains.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support for this research was provided by Research and Development Corporation of Newfoundland and Labrador, which is gratefully acknowledged. The authors would also like to acknowledge the comments from Dr. Bipul Hawlader in the Department of Civil Engineering at Memorial University of Newfoundland.
References
Ali, I. M. (2017). “Mechanical properties of an exhumed cast iron pipe material.” Master thesis, Faculty of Engineering and Applied Science, Memorial Univ. of Newfoundland, St. John’s, NL, Canada.
ANSYS version 16.2 [Computer software]. ANSYS, Canonsburg, PA.
ASM (American Society for Metals). (1990). “Properties and selection: Irons, steels, and high-performance alloys.” ⟨http://www.asminternational.org.⟩ (Oct. 15, 2015).
AWWSC (American Water Works Service Co.). (2002). “Deteriorating buried infrastructure management challenges and strategies.” ⟨http://www.epa.gov/safewater/⟩ (May 16, 2016).
Balkaya, M., Moore, I. D., and Sağlamer, A. (2012). “Study of nonuniform bedding support because of erosion under cast iron water distribution pipes.” J. Geotech. Geoenviron. Eng., 1247–1256.
Dhar, A. S., Moore, I. D., and McGrath, T. J. (2004). “Two-dimensional analyses of thermoplastic culvert deformations and strains.” J. Geotech. Geoenviron. Eng., 199–208.
Folkman, S. (2012). “Water main break rates in the USA and Canada: A comprehensive study.”, Utah State Univ. Buried Structures Laboratory, Logan, UT.
Liyanage, K. T. H. (2016). “Numerical investigation of failure mechanisms of cast iron water mains.” Master thesis, Faculty of Engineering and Applied Science, Memorial Univ. of Newfoundland, St. John’s, NL, Canada.
Liyanage, K. T. H., and Dhar, A. S. (2015). “Three dimensional finite element analyses of partially supported water mains.” 68th Canadian Geotechnical Conf. GeoQuebec 2015, Canadian Geotechnial Society, Richmond, BC, Canada.
Liyanage, K. T. H., and Dhar, A. S. (2017). “Stresses in cast iron water mains subjected to nonuniform bedding and localized concentrated forces.” Int. J. Geotech. Eng., 1–9.
Makar, J. M., Rogge, R., McDonald, S., and Tesfamariam, S. (2005). “The effect of corrosion pitting on circumferential failures in grey iron pipes.”, American Water Works Association, Denver, 115.
Rajani, B., and Kleiner, Y. (2010). “Fatigue failure of large-diameter cast iron mains.” Water distribution system analysis 2010, ASCE, Reston, VA.
Rajani, B., Makar, J., McDonald, S., Jen, C., and Viens, M. (2000). “Investigation of grey cast iron water mains to develop a methodology for estimating service life.”, AWWA Research Foundation and American Water Works Association, Denver.
Rajani, B., and Tesfamariam, S. (2004). “Uncoupled axial, flexural, and circumferential pipe–soil interaction analyses of partially supported jointed water mains.” Can. Geotech. J., 41(6), 997–1010.
Rajani, B. B., Zhan, C., and Kuraoka, S. (1996). “Pipe-soil interaction analysis of jointed water mains.” Can. Geotech. J., 33(3), 393–404.
Trickey, S. A., Moore, I. D., and Balkaya, M. (2016). “Parametric study of frost-induced bending moments in buried cast iron water pipes.” Tunnelling Underground Space Technol., 51(2016), 291–300.
Webb, M. C. (2015). “Development of constrained soil modulus values for buried pipe design.” Proc., ASCE Pipelines 2015 Conf., Baltimore, 1695–1710.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Nov 30, 2016
Accepted: May 8, 2017
Published online: Aug 11, 2017
Published in print: Nov 1, 2017
Discussion open until: Jan 11, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.