Quantitative Analysis of Mechanical Strength of Three-Phase Rigid Polyurethane Foam Composites Immersed with Water
Publication: Journal of Materials in Civil Engineering
Volume 35, Issue 2
Abstract
The mechanical properties of rigid polyurethane foam (PUF) will be significantly affected because of the existence of water when applied in dam repair and road maintenance. The related studies generally consider the effects of water and matrix on the mechanical properties of rigid PUF. However, PUF is a three-phase composite consisting of water, air, and matrix in practical engineering. Its mechanical properties are subject to the combined effects of these three composites at the same time. In this case, an improved three-phase viscoelastic model was proposed to quantify the effects of water, air, and matrix on the compressive mechanical behavior of rigid polyurethane foam immersed in water (WRPF). Based on the improved viscoelastic model and piecewise method, a compressive strength prediction model of WRPF was developed to describe the change of WRPF’s compressive strength during the full-service life. Then uniaxial compression tests and electron microscope tests were conducted to verify the rationality of the model. Results show that water and air have reinforcing effects on the compressive property of WRPF in the short-term, unsaturated absorption stage. In contrast, water has weakening effects on its compressive property in the long-term, saturated stage. Finally, at different stages of water absorption, a semitheoretical and empirical formula was developed from the prediction model and the experimental data from compressive tests.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This work was supported by the National Natural Science Foundation of China (Grant Nos. 52078177 and 51408005), Fundamental Research Funds for the Central Universities (Grant No. PA2020GDKC0007).
References
Andersons, J., M. Kirpluks, L. Stiebra, and U. Cabulis. 2016. “Anisotropy of the stiffness and strength of rigid low-density closed-cell polyisocyanurate foams.” Mater. Des. 92 (Feb): 836–845. https://doi.org/10.1016/j.matdes.2015.12.122.
Asadpoure, A., M. Tootkaboni, and L. Valdevit. 2017. “Topology optimization of multiphase architected materials for energy dissipation.” Comput. Methods Appl. Mech. Eng. 325 (Oct): 314–329. https://doi.org/10.1016/j.cma.2017.07.007.
ASTM. 2005. Standard test method for water absorption of plastics. ASTM D570. West Conshohocken, PA: ASTM.
ASTM. 2010. Standard test method for compressive properties of rigid cellular plastics. ASTM D1621. West Conshohocken, PA: ASTM.
Baroutaji, A., M. Sajjia, and A. G. Olabi. 2017. “On the crashworthiness performance of thin-walled energy absorbers: Recent advances and future developments.” Thin-Walled Struct. 118 (Sep): 137–163. https://doi.org/10.1016/j.tws.2017.05.018.
Chen, Y. M., R. Das, and M. Battley. 2015. “Effects of cell size and cell wall thickness variations on the stiffness of closed-cell foams.” Int. J. Solids Struct. 52 (Jan): 150–164. https://doi.org/10.1016/j.ijsolstr.2014.09.022.
Darcy, H. 1856. Les fontaines publiques de la ville de Dijon. Paris: Dalmont.
Dawson, M. A., G. H. Mckinley, and L. J. Gibson. 2008. “The dynamic compressive response of open-cell foam impregnated with a Newtonian fluid.” J. Appl. Mech. 75 (4): 041015. https://doi.org/10.1115/1.2912940.
Dawson, M. A., G. H. Mckinley, and L. J. Gibson. 2009. “The dynamic compressive response of an open-cell foam impregnated with a non-Newtonian fluid.” J. Appl. Mech. 76 (6): 061011. https://doi.org/10.1115/1.3130825.
Gibson, L. J., and M. F. Ashby. 1999. Cellular solids: Structure and properties. New York: Cambridge University Press.
Grosjean, F., N. Bouchonneau, D. Choqueuse, and V. Sauvant-Moynot. 2009. “Comprehensive analyses of syntactic foam behaviour in deepwater environment.” J. Mater. Sci. 44 (6): 1462–1468. https://doi.org/10.1007/s10853-008-3166-0.
Hao, M. M., F. M. Wang, X. L. Li, B. Zhang, and Y. H. Zhong. 2018. “Numerical and experimental studies of diffusion law of grouting with expansible polymer.” J. Mater. Civ. Eng. 30 (2): 04017290. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002130.
He, W. H., and H. L. Chen. 2012. “Stress and energy absorption of open-celled foam under elastic compression.” Adv. Sci. Lett. 6 (1): 518–521. https://doi.org/10.1166/asl.2012.2211.
Hilyard, N. C. 1971. “Observations on the impact behaviour of polyurethane foams: II. The effect of fluid flow.” J. Cell. Plast. 7 (2): 84–90. https://doi.org/10.1177/0021955X7100700203.
Ishak, Z. A. M., B. N. Yow, B. L. Ng, H. A. Khalil, and H. D. Rozman. 2001. “Hygrothermal aging and tensile behavior of injection‐molded rice husk‐filled polypropylene composites.” J. Appl. Polym. Sci. 81 (3): 742–753. https://doi.org/10.1002/app.1491.
Jiao, W. X., A. M. Sha, Z. Z. Liu, W. Li, L. Zhang, and S. Z. Jiang. 2022. “Optimization design and prediction of the snow-melting pavement based on electrical-thermal system.” Cold Reg. Sci. Technol. 193 (Jan): 103406. https://doi.org/10.1016/j.coldregions.2021.103406.
Kaewunruen, S., C. Ngamkhanong, M. Papaelias, and C. Roberts. 2018. “Wet/dry influence on behaviors of closed-cell polymeric cross-linked foams under static, dynamic and impact loads.” Constr. Build. Mater. 187 (Oct): 1092–1102. https://doi.org/10.1016/j.conbuildmat.2018.08.052.
Koohbor, B., A. Kidane, and W. Lu. 2016a. “Characterizing the constitutive response and energy absorption of rigid polymeric foams subjected to intermediate-velocity impact.” Polym. Test. 54 (Sep): 48–58. https://doi.org/10.1016/j.polymertesting.2016.06.023.
Koohbor, B., A. Kidane, and W. Lu. 2016b. “Effect of specimen size, compressibility and inertia on the response of rigid polymer foams subjected to high velocity direct impact loading.” Int. J. Impact Eng. 98 (Dec): 62–74. https://doi.org/10.1016/j.ijimpeng.2016.08.006.
Linul, E., P. A. Linul, C. Valean, L. Marsavina, and D. Silaghi-Perju. 2018. “Manufacturing and compressive mechanical behavior of reinforced polyurethane flexible (PUF) foams.” Mater. Sci. Eng. 416 (1): 012053. https://doi.org/10.1088/1757-899X/416/1/012053.
Linul, E., L. Marsavina, C. Valean, and R. Banica. 2020. “Static and dynamic mode I fracture toughness of rigid PUR foams under room and cryogenic temperatures.” Eng. Fract. Mech. 225 (Feb): 106274. https://doi.org/10.1016/j.engfracmech.2018.12.007.
Liu, K., Y. Li, F. Wang, H. Xie, H. Pang, and H. Bai. 2019a. “Analytical and model studies on behavior of rigid polyurethane composite aggregate under compression.” J. Mater. Civ. Eng. 31 (3): 04019007. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002641.
Liu, K., W. Liang, F. M. Ren, J. G. Ren, F. Wang, and D. Heng. 2019b. “The study on compressive mechanical properties of rigid polyurethane grout materials with different densities.” Constr. Build. Mater. 206 (May): 270–278. https://doi.org/10.1016/j.conbuildmat.2019.02.012.
Liu, K., P. X. Xu, F. Wang, L. Y. You, X. C. Zhang, and C. L. Fu. 2022. “Assessment of automatic induction self-healing treatment applied to steel deck asphalt pavement.” Autom. Constr. 133 (Jan): 104011. https://doi.org/10.1016/j.autcon.2021.104011.
Lu, W. Y., M. Neidigk, and N. Wyatt. 2017. “Cyclic loading experiment for characterizing foam viscoelastic behavior.” Exp. Appl. Mech. (4): 135–144. https://doi.org/10.1007/978-3-319-42028-8_16.
Manujesh, B. J., V. Rao, and M. P. S. Aan. 2014. “Moisture absorption and mechanical degradation studies of polyurethane foam cored E-glass-reinforced vinyl-ester sandwich composites.” J. Reinf. Plast. Compos. 5 (33): 479–492. https://doi.org/10.1177/0731684413503720.
Marsavina, L., K. Jaroslav, and L. Emanoil. 2016. “Experimental validation of micromechanical models for brittle aluminum alloy foam.” J. Appl. Polym. Sci. 83 (Jun): 11–18. https://doi.org/10.1016/j.tafmec.2015.12.020.
Marsavina, L., and E. Linul. 2020. “Fracture toughness of rigid polymeric foams: A review.” Fatigue Fract. Eng. Mater. Struct. 43 (11): 2483–2514. https://doi.org/10.1111/ffe.13327.
May-Pat, A., and F. Avilés. 2014. “Long term water uptake of a low density polyvinyl chloride foam and its effect on the foam microstructure and mechanical properties.” Mater. Des. 57 (May): 728–735. https://doi.org/10.1016/j.matdes.2014.01.042.
Mills, N. J., and G. Lyn. 2002. “Modelling of air flow in impacted polyurethane foam.” Cell. Polym. 21 (5): 343–368. https://doi.org/10.1177/026248930202100502.
Misra, A., P. Kumar, J. R. Raney, A. Singhal, L. Lattanzi, and C. Daraio. 2014. “Effect of fluid medium on mechanical behavior of carbon nanotube foam.” Appl. Phys. Lett. 104 (22): 221910. https://doi.org/10.1063/1.4881843.
Motokucho, S., A. Yamaguchi, Y. Nakayama, H. Morikawa, and H. Nakatani. 2017. “Hydrolysis of aromatic polyurethane in water under high pressure of .” J. Polym. Sci., Part A: Polym. Chem. 55 (12): 2004–2010. https://doi.org/10.1002/pola.28576.
Park, K. B., H. T. Kim, N. Y. Her, and J. M. Lee. 2019. “Variation of mechanical characteristics of polyurethane foam: Effect of test method.” Materials 12 (17): 2672. https://doi.org/10.3390/ma12172672.
Poveda, R. L., G. Dorogokupets, and N. Gupta. 2013. “Carbon nanofiber reinforced syntactic foams: Degradation mechanism for long term moisture exposure and residual compressive properties.” Polym. Degrad. Stab. 98 (10): 2041–2053. https://doi.org/10.1016/j.polymdegradstab.2013.07.007.
Qu, J., D. W. Ju, S. R. Gao, and J. W. Chen. 2018. “Research on the dynamic mechanical properties of polymethacrylimide foam sandwich structure.” Compos. Struct. 204 (Nov): 22–30. https://doi.org/10.1016/j.compstruct.2018.07.078.
Rehkopf, J. D., G. W. Brodland, and G. M. Mcneice. 1996a. “Experimentally separating fluid and matrix contributions to polymeric foam behavior.” Exp. Mech. 36 (1): 1–6. https://doi.org/10.1007/BF02328691.
Rehkopf, J. D., G. W. Brodland, and G. M. Mcneice. 1996b. “Fluid and matrix components of polyurethane foam behavior under cyclic compression.” J. Eng. Mater. Technol. 118 (1): 58–62. https://doi.org/10.1115/1.2805934.
Romhild, S., G. Bergman, and M. S. Hedenqvist. 2010. “Short-term and long-term performance of thermosets exposed to water at elevated temperatures.” J. Appl. Polym. Sci. 116 (2): 1057–1067. https://doi.org/10.1002/app.31548.
Sadler, R. L., M. Sharpe, R. Panduranga, and K. Shivakumar. 2009. “Water immersion effect on swelling and compression properties of Eco-Core, PVC foam and balsa wood.” Compos. Struct. 90 (3): 330–336. https://doi.org/10.1016/j.compstruct.2009.03.016.
Sauvant-Moynot, N., N. Gimenez, and H. Sautereau. 2006. “Hydrolytic ageing of syntactic foams for thermal insulation in deep water: Degradation mechanisms and water uptake model.” J. Mater. Sci. 41 (13): 4047–4054. https://doi.org/10.1007/s10853-006-7618-0.
Savelyev, Y., L. Markovskaya, O. Savelyeva, E. Akhranovich, N. Parkhomenko, and T. Travinskaya. 2015. “Degradable polyurethane foams based on disaccharides.” J. Appl. Polym. Sci. 132 (25): 42131. https://doi.org/10.1002/app.42131.
Schraad, M. W., and F. H. Harlow. 2006. “A multi-field approach to modeling the dynamic response of cellular materials.” Int. J. Mech. Sci. 48 (1): 85–106. https://doi.org/10.1016/j.ijmecsci.2005.09.004.
Serban, D. A., R. Negru, H. Filipescu, and L. Marsavina. 2020. “Investigations on the influence of the triaxial state of stress on the failure of polyurethane rigid foams.” Continuum Mech. Thermodyn. 1–14. https://doi.org/10.1007/s00161-020-00924-x.
Shen, Y., F. Golnaraghi, and A. Plumtree. 2001. “Modeling compressive cyclic stress-strain behavior of structural foam.” Int. J. Fatigue 23 (6): 491–497. https://doi.org/10.1016/S0142-1123(01)00014-7.
Siivola, J. T., S. Minakuchi, and N. Takeda. 2015. “Effect of temperature and humidity conditions on polymethacrylimide (PMI) foam core material and indentation response of its sandwich structures.” J. Sandwich Struct. Mater. 17 (4): 335–358. https://doi.org/10.1177/1099636215570831.
Siriruk, A., D. Penumadu, and A. Sharma. 2012. “Effects of seawater and low temperatures on polymeric foam core material.” Exp. Mech. 52 (1): 25–36. https://doi.org/10.1007/s11340-011-9564-2.
Somarathna, H. M. C. C., S. N. Raman, D. Mohotti, A. A. Mutalib, and K. H. Badri. 2018. “The use of polyurethane for structural and infrastructural engineering applications: A state-of-the-art review.” Constr. Build. Mater. 190 (Nov): 995–1014. https://doi.org/10.1016/j.conbuildmat.2018.09.166.
Soutrenon, M., and V. Michaud. 2014. “Impact properties of shear thickening fluid impregnated foams.” Smart Mater. Struct. 23 (3): 035022. https://doi.org/10.1088/0964-1726/23/3/035022.
Törzs, T., G. Lu, A. O. Monteiro, D. Wang, J. Grabe, and M. Oeser. 2019. “Hydraulic properties of polyurethane-bound permeable pavement materials considering unsaturated flow.” Constr. Build. Mater. 212 (Jul): 422–430. https://doi.org/10.1016/j.conbuildmat.2019.03.201.
Wang, J., H. Wang, B. Chen, H. Huang, and S. Liu. 2017. “A failure mechanism based model for numerical modeling the compression-after-impact of foam-core sandwich panels.” Compos. Sci. Technol. 151 (Oct): 258–267. https://doi.org/10.1016/j.compscitech.2017.08.027.
Wang, Z. Y., M. R. Du, H. Y. Fang, C. Zhang, M. J. Li, and M. S. Shi. 2021. “Influence of different corrosion environments on mechanical properties of a roadbed rehabilitation polyurethane grouting material under uniaxial compression.” Constr. Build. Mater. 301 (Sep): 124092. https://doi.org/10.1016/j.conbuildmat.2021.124092.
Wei, Y., F. M. Wang, X. Gao, and Y. H. Zhong. 2017. “Microstructure and fatigue performance of polyurethane grout materials under compression.” J. Mater. Civ. Eng. 22 (9): 04017101. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001954.
You, L. Y., Z. You, Q. Dai, S. Guo, J. Wang, and M. Schultz. 2018. “Characteristics of water-foamed asphalt mixture under multiple freeze-thaw cycles: Laboratory evaluation.” J. Mater. Civ. Eng. 30 (11): 04019007. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002474.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Sep 16, 2021
Accepted: May 23, 2022
Published online: Nov 29, 2022
Published in print: Feb 1, 2023
Discussion open until: Apr 29, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.